Fluke networks intellitone pro 200 инструкция

August 2014, Rev. 2 9/2017 2014, 2017 Fluke Corporation All product names are trademarks of their respective companies.

IntelliTone Pro 200 LAN Toner and 200 Probe

Users Manual

LIMITED WARRANTY AND LIMITATION OF LIABILITY Each Fluke Networks product is warranted to be free from defects in material and workmanship under normal use and service unless stated otherwise herein. The warranty period for the mainframe is one year and begins on the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories. The warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller, and does not apply to any product which, in Fluke Networks opinion, has been misused, abused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke Networks does not warrant that software will be error free or operate without interruption. Fluke Networks authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks. Warranty support is available only if product is purchased through a Fluke Networks authorized sales outlet or Buyer has paid the applicable international price. To the extent permitted by law, Fluke Networks reserves the right to invoice Buyer for repair/replacement when a product purchased in one country is submitted for repair in another country. For a list of authorized resellers, visit www.flukenetworks.com/wheretobuy. Fluke Networks warranty obligation is limited, at Fluke Networks option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke Networks authorized service center within the warranty period. To obtain warranty service, contact your nearest Fluke Networks authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB destination). Fluke Networks assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB destination). If Fluke Networks determines that failure was caused by neglect, misuse, contamination, alteration, accident or abnormal condition of operation or handling, or normal wear and tear of mechanical components, Fluke Networks will provide an estimate of repair costs and obtain authorization before commencing the work. Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges (FOB Shipping point). THIS WARRANTY IS BUYERS SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE NETWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY CAUSE OR THEORY. Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any other provision.

4/15

Fluke Networks PO Box 777 Everett, WA 98206-0777 USA

i

Contents

Title Page

Overview of Features ……………………………………………………………………………………… 1

Registration …………………………………………………………………………………………………… 1

Contacting Fluke Networks …………………………………………………………………………….. 2

Unpacking ……………………………………………………………………………………………………… 2

IT200 IntelliTone Pro LAN Kit ……………………………………………………………………… 2

IT200 IntelliTone Pro LAN Toner …………………………………………………………………. 2

IP200 IntelliTone Pro Probe ………………………………………………………………………… 2

Symbols …………………………………………………………………………………………………………. 2

WSafety Information ……………………………………………………………………………….. 4

Battery Status ………………………………………………………………………………………………… 4

Auto Power Down ………………………………………………………………………………………….. 4

Locating and Isolating Terminated UTP/STP Cables with the IntelliTone …………….. 5

IntelliTone Pro 200 LAN Users Manual

ii

Isolating Individual Wire Pairs with the SmartTone Analog Function …………………. 7

SmartTone Positive Identification ……………………………………………………………….. 7

Validating RJ11 and RJ45 Cable Maps ……………………………………………………………… 8

Validating the Cables Shield …………………………………………………………………………… 10

Validating Ethernet Service …………………………………………………………………………….. 11

Testing for Continuity …………………………………………………………………………………….. 12

Maintenance ………………………………………………………………………………………………….. 12

Battery Life and Replacement …………………………………………………………………….. 13

Accessories ………………………………………………………………………………………………… 14

Specifications …………………………………………………………………………………………………. 15

IT200 Toner Electrical Specifications ……………………………………………………………. 16

IP200 Probe Electrical Specifications ……………………………………………………………. 16

Feature Compatibility ………………………………………………………………………………… 17

Dimensions ………………………………………………………………………………………………… 17

Weight (with battery) ………………………………………………………………………………… 17

1

IntelliTone Pro 200 LAN Toner IntelliTone Pro 200 Probe

Overview of Features

The IntelliTonePro 200 LAN toner and Pro 200 probe let you locate, isolate, and validate twisted pair (UTP, Cat 5e, Cat 6), coax cables (RG6, RG59, and others for CATV/CCTV), bare wire (such as speaker wire and security network wire), and Cat 3 telephone cabling. The toner also lets you validate data services.

The toner and probe feature both digital and analog toning and detection. The digital IntelliTone tone is primarily used on data cables, and on active networks. In these environments, the digital signal eliminates cable misidentification due to signal bleed and radiated or ambient noise.

The analog tone is primarily used on voice cables, and on bare wire. The SmartTone analog technology will change cadence when a pair is shorted at the far end. This makes exact pair identification easy and precise.

The IntelliTone feature also lets you use the toner and probe to validate and troubleshoot wiring on RJ11 and RJ45 cables.

The toner detects Ethernet service and indicates active pair number on Ethernet circuits.

The toner and probe also provide standard functions such as visual and audible signal strength indication, digital toning/detection, SmartTone analog toning/detection, and continuity testing.

Registration

Registering your product with Fluke Networks gives you access to valuable information on product updates, troubleshooting tips, and other support services. To register, fill out the online registration form on the Fluke Networks website at www.flukenetworks.com/ registration.

IntelliTone Pro 200 LAN Users Manual

2

Contacting Fluke Networks

Fluke Networks operates in more than 50 countries worldwide. For more contact information, go to our website.

Unpacking

The IntelliTone products come with the accessories listed below. If an accessory is damaged or missing, contact the place of purchase immediately.

IT200 IntelliTone Pro LAN Kit

IT200 Toner with 9 V battery

IP200 Probe with 9 V battery

2 RJ11 to RJ11 patch cords

2 RJ45 to RJ45 patch cords

Test lead set, banana jacks to alligator clips

F connector adapter, female to female

Quick Reference Guide

IT200 IntelliTone Pro LAN Toner

IT200 Toner with 9 V battery

1 RJ11 to RJ11 patch cord

1 RJ45 to RJ45 patch cord

Test lead set, banana jacks to alligator clips

F connector adapter, female to female

Quick Reference Guide

IP200 IntelliTone Pro Probe

IP200 Probe with 9 V battery

Quick Reference Guide

Symbols

Table 1 describes the symbols used on the tester and in this manual.

www.flukenetworks.com/support

info@flukenetworks.com

1-800-283-5853, +1-425-446-5500

Fluke Networks 6920 Seaway Boulevard, MS 143F Everett WA 98203 USA

Symbols

3

Table 1. Symbols

Warning or Caution: Risk of damage or destruction to equipment or software. See explanations in the manuals.

Warning: Risk of fire, electric shock, or personal injury.

This equipment not for connection to public communications networks, such as active telephone systems.

Consult the user documentation.

This product complies with the WEEE Directive marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as category 9 «Monitoring and Control Instrumentation» product. Do not dispose of this product as unsorted municipal waste.

To return unwanted products, contact the manufacturers web site shown on the product or your local sales office or distributor.

40 year Environment Friendly Use Period (EFUP) under China Regulation — Administrative Measure on the Control of Pollution Caused by Electronic Information Products. This is the period of time before any of the identified hazardous substances are likely to leak out, causing possible harm to health and the environment.

Conformite Europeene. Conforms to the requirements of the European Union and the European Free Trade Association (EFTA).

Korea (KCC): Class A Equipment (Industrial Broadcasting and Communication Equipment). Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and is not to be used in homes.

Conforms to relevant Australian standards.

W

X

j

~

P

IntelliTone Pro 200 LAN Users Manual

4

WSafety Information

WWarningX To prevent possible fire, electric shock, or personal injury:

Never use the toner, probe, or test leads if they are damaged. Inspect the cases and test leads for damage before use.

Never open the case except to change the battery; no user-serviceable parts are inside.

Turn off the toner or probe and disconnect all test leads before replacing the battery.

Use only a 9V battery, properly installed in the case, to power the toner and probe.

If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

WCaution

Avoid touching the probe tip to patch panel connections and using the tip to dig into cable bundles. Doing so regularly may damage the probe tip over time.

To avoid unreliable test results, replace the battery as soon as the low battery indication appears.

Battery Status

LEDs on the toner and probe light for 1 second at power on to indicate the battery status:

Green: Battery is good.

Yellow: Battery is marginal.

Red: Battery is low.

See Battery Life and Replacement on page 16 for more information on the battery.

Auto Power Down

The toner turns off automatically after approximately 2 hours of inactivity. The probe turns off automatically after 1 hour of inactivity.

Toner battery status LED

Probe battery status LED

Locating and Isolating Terminated UTP/STP Cables with the IntelliTone

5

To reactivate the toner or probe, turn the rotary switch to any position except OFF.

Locating and Isolating Terminated UTP/STP Cables with the IntelliTone

The IntelliTone Pro toner provides two toning modes for locating and isolating cables: one digital tone and the SmartTone analog tones (500 Hz to 1200 Hz) .

With the toner set to digital tone mode, the probe can be set to either locate or isolate .

Both toning signals are available at all connectors on the toner.

The digital tone is optimized for 4 pair UTP data environments and the SmartTone analog tone is optimized for two wire locating.

To locate and isolate cables using the digital tone, do the following:

1 Connect the IT200 toner to a jack or punch-down block as shown in Figure 1.

2 Turn the toners rotary switch to .

3 Turn the IP200 probes rotary switch to (locate).

4 Use the probe to find the general location of the tone at a cable rack, patch panel, or behind a wall. The SYNC LED lights up green when the probe is receiving the IntelliTone signal.

In locating mode, the probes LEDs light up from 1 to 8 as the signal strength increases. The higher the number, the stronger the signal.

Note

If you cannot locate the IntelliTone signal on 2-conductor cables, the cable may be shorted. Use the cable map test (page to test for shorts on cables with RJ11 and RJ45 connectors. Use the continuity test (page 12) to check for shorts on coax and non-terminated cables.

5 Turn the probes rotary switch to (isolate).

6 Use the probe to isolate the tone source in the cable bundle or at the patch panel. The SYNC LED lights up green when the probe is receiving the IntelliTone signal.

In isolating mode, the probes LEDs light up from 1 to 8 as the signal strength increases.

IntelliTone Pro 200 LAN Users Manual

6

ASH04.EPS

Figure 1. Locating and Isolating Cables

Locating Cables Isolating Cables

Volume control

Digital toning

SmartToneTM, Analog 1kHz

toning

Connecting the Toner

Isolating Individual Wire Pairs with the SmartTone Analog Function

7

Isolating Individual Wire Pairs with the SmartTone Analog Function

The position on the IntelliTone probe and toner lets you use the probe to trace using an analog tone.

SmartTone is intended for use on dry pairs of wires that are un-terminated at both ends of the run. It is not intended to be used on live wires with a DC power source (e.g., live telephone lines), nor will it work on wire pairs that are carrying AC signals. SmartTone works on many types of wire pairs including twisted pair, house wiring, and coax (the shield is one wire and the center conductor is the other wire of the pair).

SmartTone Positive Identification

1 The toner red lead must be connected to one of the wires of the pair, and the black lead must be connected to the other wire of the pair.

2 Put the toner and probe in the position.

3 At the far end of the cable run, place the probe near the wires you are tracing. Pick the pair that gives the loudest signal in the toner speaker.

4 Short and release the two wires of the pair. If you hear a change in the pattern of the tone, then you have located the target pair of wires.

If you dont hear a change in the tone pattern, then pick a different pair and try again until you find the pair that causes the tone pattern to change.

IntelliTone Pro 200 LAN Users Manual

8

Validating RJ11 and RJ45 Cable Maps

You can use the IT200 toner and IP200 probe to validate the cable map on RJ11 and RJ45 connectors. The cable map function finds the most common wiring faults on twisted pair cabling: shorts, opens, and crossed pairs.

1 Connect an IT200 toner to a RJ11 or RJ45 jack, as shown in Figure 2.

2 Turn the toners rotary switch to .

3 If necessary, use the IP200 probe to locate the correct connector at the other end of the cabling, as described in the previous section.

4 Connect the IP200 probe to the RJ11 or RJ45 jack; then turn the probes rotary switch to CABLE MAP.

5 The probes LEDs and beeper indicate the cable map, as follows:

The number of each LED corresponds to a pin on the connector. You can enable the SYNC LED to validate the shield. See Validating the Cables Shield on page 10.

Each LED that corresponding to an active pin flashes briefly, then should light for about 1 second. The brief flash shows which LED is next in the sequence.

The probe also beeps in different tones to indicate good wiring, miswires, shorts, and opens.

Miswire: If one LED flashes briefly, then another LED lights for one second, the wire for the first LED is miswired to the pin for the second LED.

Short: If two LEDs turn on for 1 second at the same time, those two pins are shorted together. If more than 2 wires are shorted together, the LEDs for the shorted pins indicate opens.

Open: If an LED flashes briefly, then no LEDs turn on, that pin is open.

Validating RJ11 and RJ45 Cable Maps

9

ASH05.EPS

Figure 2. Validating Cable Maps

IN TELLIT

O N

E Pro

200 PRO BE

…

…

…

4 3 2 1

4 3 2 1

4 3 2 1

4 3 2 1

= Shield (If enabled. See text.)

4 3 2 1

4 3 2 1

…

…

… MAP

IntelliTone Pro 200 LAN Users Manual

10

Validating the Cables Shield

To use the probes SYNC LED for shield validation during cable map tests, do the following:

1 Remove the battery door and disconnect the battery from the probe, as described under Battery Life and Replacement on page 13.

2 Turn the probes rotary switch to CABLE MAP.

Note

The battery must be disconnected from the probe for at least 30 seconds.

3 Replace the battery and battery door.

The SYNC LED will now indicate a good, open, or shorted shield as described in the previous section.

To disable shield validation via the probes SYNC LED, do the following:

1 Remove the battery door and disconnect the battery from the probe.

2 Turn the probes rotary switch any position except CABLE MAP.

Note

The battery must be disconnected from the probe for at least 30 seconds.

3 Replace the battery and battery door.

Validating Ethernet Service

11

Validating Ethernet Service

The toner detects link pulses for 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet service on pins 1, 2 and 3, 6 of its RJ45 jack.

1 Turn off the toner.

2 Connect the toner to the circuit as shown in Figure 3.

3 Turn the toners rotary switch to SERVICE.

4 The Ethernet LED indicates service on pins 1, 2 or 3, 6 as shown in Figure 3.

The toner checks for continuity between pins 4, 5. Continuity indicates the toner is connected to a network device that is turned off.

The toner checks for continuity between the red and black test leads and across the middle pair of the RJ45/RJ11 jack (line 1).

Note

If the Ethernet LED alternates between red and green, the Ethernet service is Auto-MDIX.

ASH01.EPS

Figure 3. Validating Ethernet Service

Punch-down block

RJ45 RJ11

SERVICE

Red: service on 1, 2

Continuity or non-Ethernet voltage

No voltage No continuity

Green: service on 3, 6

IntelliTone Pro 200 LAN Users Manual

12

Testing for Continuity

You can use the toner to test circuits and components for continuity.

1 If you are testing a circuit, verify that it is not powered. Use the toners continuity function to check for continuity. Use a voltage meter to check other types of circuits for power.

2 Turn off the toner.

3 Connect the toner to the circuit or component as shown in Figure 4.

4 Turn the toners rotary switch to .

5 The LED indicates an open or closed circuit as shown in Figure 4.

ASH09.EPS

Figure 4. Continuity Test

Maintenance

Clean the case with a soft cloth dampened with water or a mild soap solution.

WCaution

To avoid damaging the case, do not use solvents or abrasive cleansers.

>10k=

=

Maintenance

13

Battery Life and Replacement

The toner and probe batteries last for about 20 hours of typical use.

Figure 5 shows how to replace the battery in the toner and probe.

Note

The position of the probes rotary switch when the battery is replaced enables or disables shield validation for cable map tests. See Validating the Cables Shield on page 10.

WWarningX To avoid possible electric shock or personal injury:

Turn off the toner or probe and disconnect all test leads before replacing the battery.

Use only a 9 V battery, properly installed in the case, to power the toner and probe.

WCaution

To avoid unreliable test results, replace the battery as soon as the low battery indication appears. See Battery Status on page 4. ASH10.EPS

Figure 5. Replacing the Battery

See text regarding probe’s switch position during battery replacement.

IntelliTone Pro 200 LAN Users Manual

14

Accessories

To order accessories (Table 2), contact Fluke Networks.

For the latest list of IntelliTone accessories and other cable testers visit the Fluke Networks website at www.flukenetworks.com.

Table 2. Accessories

Test lead set, banana jacks to alligator clips

MT-8203-22

Test lead set, banana jacks to alligator clips with bed of nails

MT-8203-20

Soft carrying case MT-8202-05

Accessory Fluke Networks Model

or Part Number

Specifications

15

Specifications

Specifications apply at 23 C (73 F), unless otherwise noted.

Environmental and Regulatory Specifications

Operating temperature 32 F to 104 F (0 C to 40 C)

Storage temperature -4 F to +140 F (-20 C to +60 C)

Operating relative humidity (% RH without condensation)

95 % (50 F to 95 F; 10 C to 35 C) 75 % (95 F to 104 F; 35 C to 40 C) Uncontrolled < 50 F (< 10 C)

Vibration Random, 2 g, 5 Hz-500 Hz

Shock 1 m drop test

Safety IEC 61010-1 , Category: None

Altitude 3000 m

EMC IEC 61326-1, FCC Part 15 B

IntelliTone Pro 200 LAN Users Manual

16

IT200 Toner Electrical Specifications

IP200 Probe Electrical Specifications

Output power 5 V p-p

Tone frequencies IntelliTone signal: encoded digital signal

Analog SmartTone signal: 500 Hz — 1200 Hz, 4 songs

Battery type and life 9V alkaline (NEDA 1604A or IEC 6LR61); 20 hours typical

Auto power down Turns off automatically after 2.5 hours of inactivity

Tone detection Detects IntelliTone digital signal for Locate, Isolate, and CableMap functions.

Detects analog SmartTone signal (500 Hz-1200 Hz) and other analog toners.

Battery type and life 9V alkaline (NEDA 1604A or IEC 6LR61); 20 hours typical

Auto power down Turns off automatically after 1 hour of inactivity

Specifications

17

Feature Compatibility

Dimensions

Toner: 5.54 in x 2.94 in x 1.25 in

(14.1 cm x 7.5 cm x 3.2 cm)

Probe: 8.73 in x 1.88 in x 1.26 in

(22.2 cm x 4.8 cm x 3.2 cm)

Weight (with battery)

Toner: 6.0 oz (170 g)

Probe: 4.7 oz (133 g)

Product Compatibility

IntelliTone Toner/Probe Feature IntelliTone Toner and Probe Works with Legacy Toner or Probe

IntelliTone locate mode

IntelliTone isolate mode