Gen part 6000 инструкция по эксплуатации

WOODWARD Genpart 6000 ( EGCP 1) and EasyGen 2500 Synchronization :-

I need to communicate WOODWARD Genpart 6000 ( EGCP 1) and WOODWARD EasyGen 2500 panels on RS 485 Network as both have this communication protocol on it .

Do anyone knows about it or has done it or seen it somewhere ?

Please give your valuable comments .

Thanks
Sarabjot Singh Manku
+234 9020323180

Maybe, your modbus is disable.

3185 or 3188 Modbus slave ID

Maybe, you must set to disable CAN bus and enable Modbus

Have you ever communicated both of the modules on RS 485 Network ?

I hope there is no need to introduce any module again in loop .

Thanks
Sarabjot Singh Manku

There is a Load share Gateway from Woodward called LSG talking same modbus like GCP-1
There is a LSG doing activ KW and another Version doing reactive kVAR sharing

LSG is between the RS485 EGCP-1/2 lines and the CANbus line of easYgen2000/3000

Oil & Industrial Services Ltd
8-10 Danjuma Drive
Trans Amadi Industrial Layout
Port Harcourt, Rivers State, Nigeria
phone– +234 (84) 461037 OR 461038
fax– +234 (84) 461036
e-mail– [email protected]
[email protected]
website– www.oisltd.com/woodward.html

EsyGen 2500 has RS485 communication protocol in it . Why can’t we use it and link it with Genpart 6000 . As Both shares the same protocol .

(08-13-2015, 05:45 PM) ssmanku1699 Wrote: Dear Clemi68 ,

EsyGen 2500 has RS485 communication protocol in it . Why can’t we use it and link it with Genpart 6000 . As Both shares the same protocol .

No, easYgen-2500 RS485 Modbus protocol is not programmed for sending/receiving kW and kVAR loadshare Messages. easYgen-2500 can do loadsharing only via CANopen, to talk to EGCP-1/2 a Woodward LSG load share Gateway (one for kW and another one for kVAR sharing required.

Источник

ПАНЕЛИ УПРАВЛЕНИЯ

Управление прежде всего! Оптимизируйте характеристики своей генераторной установки и возьмите управление в свои руки! Мы можем предоставить Вам систему управления, которая будет отвечать Вашим нуждам независимо от Ваших энергетических потребностей .

Безопасные и простые в использовании системы панелей управления:

• синхронизация нескольких установок;
• установки для параллельной работы с сетью;
• интеллектуальные системы переключения нагрузки;
• дисплеи интерфейса оператора;
• защита сетей;
• устройства удаленного мониторинга — от простейших сигнальных устройств до дисплеев SCADA;
• изготовляемые по заказу распределительные устройства в контейнерном исполнении;
• сложные и мощные средства управления зданием и нагрузками, построенные на базе программируемых логических контроллеров.

Цифровые панели управления FG Wilson — это продукт высоких технологий, безопасные и простые в использовании, обладающие всеми необходимыми средствами контроля и управления электрогенераторами, от запускаемых с помощью ключа до автоматических, цифровых и синхронизирующих систем, а также дополнительные системы дистанционного управления.

Электрогенераторы FG Wilson — как газовые, так и дизельные, — полностью автоматизированные устройства, оборудованные системами самоконтроля и диагностики, эксплуатация которых осуществляется по принципу «безлюдной технологии» — генераторы самостоятельно запускаются в работу, обеспечивая объект электричеством в требуемом объеме, регулируют свои рабочие характеристики, сигнализируют об опасностях и неисправностях.
Центром управления всей деятельностью электрогенератора и его «интерфейсом» — являются панели управления.

Цифровые многофункциональные панели управления PowerWizard — это ПОЛНОЕ УПРАВЛЕНИЕ ОДНИМ НАЖАТИЕМ КНОПКИ!

Системы управления PowerWizard представляют эффективные способы контроля и связи генераторной установки. При использовании новейших технологий панель управления PowerWizard сводит на одном дисплее показания измерителей и датчиков для обеспечения быстрого и удобного доступа к параметрам элементов управления, измерительных и защитных устройств и данным диагностического характера.

Разработанные компанией CAT Electronics — лидером промышленных электронных систем управления, системы управления подвергаются жесткому контролю при высоких и низких температурах, в условиях высокой влажности и солевого тумана, через погружение в химикаты, в условиях вибрации и подвергаясь ударным воздействиям, проходя более 10 000 часов испытаний в условиях эксплуатации. Передняя крышка панелей изготавливается из литого алюминия, рассчитана на тяжелые условия работы выполнена по стандарту герметичности — IP56. Панели имеют жидкокристаллический дисплей с подсветкой, клавиатуру управления и перемещения, 70-ти контактный соединитель с блокировкой с винтами.

Источник

Thanks. We have received your request and will respond promptly.

Come Join Us!

• Talk With Other Members
• Be Notified Of Responses
  To Your Posts
• Keyword Search
• One-Click Access To Your
  Favorite Forums
• Automated Signatures
  On Your Posts
• Best Of All, It’s Free!

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

FG wilson Generator gen part 6000 control panel

FG wilson Generator gen part 6000 control panel

FG wilson Generator gen part 6000 control panel

Hello my name is alastair and I am new to the forum so, Hello!

I am currently out on a job at a Standby power generator that hasnt been started in 6 years!
Its a containerised Fg Wilson generator.
Engine is a perkins 3000 series V style.
500KVA
Control module is a genpart 6000 (Never encountered this style of module)

I arrive on site to which the site contact explains the generator was disconected from the ac mains 6 years ago alongs with the batteries to start it.
They want to get it running again and mount it on an articulated lorry so they can have mobile backup power between sites, so there wont be any need for a means of ac mains for a battery charger or water jacket heater.

I connect the two batteries in series to give 24v to the starter motor and dc system.
Genpart 6000 lights up for 1 sec then dulls with loads of square boxes on screen?
There is a 4 way rotary switch. 1 being off, 2 being auto, 3 being test and 4 being run.
nothing happens when they are switched?
I did not try to jump the starter incase I had no control over the governance of the engine plus it probally wouldnt have started anyway with the fuel solenoid being closed.

So my questions are:
#1 what would you do in this situation ?
#2 Where to start?
#3 Ever done anything like this before during installations?

The gen part 6000 might be broken ect but Would that stop the engine from starting? as it is started by a rotary switch independant of the module.

RE: FG wilson Generator gen part 6000 control panel

Step 1: Get some heat on the generator end to ensure that the windings are dry. This may take a day or more.
Do not attempt to start the set until you get good megger readings on the windings.
Step 2: Remove the circuit boards from the control panel and clean and dry the boards.
Step 3: Reinstall the circuit boards.
Step 4: Inspect the control wiring for corroded or loose connections.
Step 5: Reconnect the batteries and check for proper voltage supplying the control panel.
Step 6: Try again to start the set with the control panel.
For an example of the possible consequence of starting a set that has been sitting for a few years see:

RE: FG wilson Generator gen part 6000 control panel

The generator end was dry as it has been sat in a container
However, Moisture may have accumulated inside the generator
and circuit boards in the control panel over the six years it sat inside the container.

I have found out that apparantley the gen part 6000 control module is obsolete, so if it is faulty I will have to replace with something along the lines of a (Deep Sea Electronics Control Module)

never replaced a module before so I take it I would be reprogramming the Inputs and outputs.

Il post some pics of inside the control panel and tell me what you make of it.
Im having trouble finding where the 24v enters the panel.

RE: FG wilson Generator gen part 6000 control panel

As Bill says, don’t try to start the unit until you make sure the generator end is ok.

As I remember the Genpart 6000 was a branded Woodward EGCP-1, does it look like this, http://www.dsf-technologies.com/upload/proddocspdf.

There were a lot of different control configurations on the FG Wilson packages, mostly depending on where the unit was originally destined to go, but most units did have the Manual start option that allowed for an engine start without the control panel active.

Maybe some pictures or more details on your unit would help.

RE: FG wilson Generator gen part 6000 control panel

Here is a picture of the front of the control panel.
I will certainly make sure the generator end is dry before start up.

Do I need the woodward genpart 6000 controller to work to actually start the generator ?
I assume all the controller does is monitor the mains input and gives me run time details?

Could I manually start by engaging the rotary switch ?

Thanks guys for helping out.

RE: FG wilson Generator gen part 6000 control panel

So your picture looks like the older 6200 control panel assembly. Usually the engine will start and run by turning the selector switch to the RUN position, however in some cases depending on which engine and governor you had the Fuel ON output from the controller was still needed. They put these panels on a lot of different engine and generator combinations, so the exact operation depends a lot on what is installed.

Your best bet is to contact FG Wilson thru your local dealer and get the correct documentation for your unit.

There are a couple of retrofit options I know of, I pretty sure DIEF or one of their bigger dealers was providing a retrofit kit, and there are a couple of China sources for panel assemblies.

Red Flag Submitted

Thank you for helping keep Eng-Tips Forums free from inappropriate posts.
The Eng-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Eng-Tips forums is a member-only feature.

Click Here to join Eng-Tips and talk with other members! Already a Member? Login

Источник

Genset Controllers

Genset controls for your power generation systems

Woodward offers a wide range of controllers for the generator set market. We strive to reduce total installed/operating cost and commissioning time while improving availability, efficiency, reliability and longevity.

We have the longest legacy of any controls supplier in the paralleling genset control market. We continuously invest in innovative solutions to real market problems and provide value to our original equipment manufacturers (OEMs), genset packagers, switchgear builders, system integrators and end user customers. Our knowledge of controls, auxiliaries and power generation systems lets us drive optimization through simplification and standardization.

Woodward provides fast response, local, knowledgeable support, and optimized, cost-effective solutions to our customers through our direct sales force as well as through our vast network of distributors. As an independent company, we are able to provide full service, support and upgrades for our current and legacy product lines.

Parallel Applications | easYgen-3000XT Series

The easYgen-3000XT Series controllers operate gensets of all sizes and applications. These controllers include specifically designed algorithms and logic to start, stop, control, and protect the genset, circuit breaker, and the utility where applicable. This technology allows standardizing on a single, affordable genset controller for distributed power generation applications. These applications can range from single stand-alone emergency backup power to parallel load sharing of multiple gensets in complex, segmented distribution systems with multiple utility feeds and tie breakers.

3100XT-P1 | 3200XT-P1 | 3200XT-P1-LT | 3400XT-P1 | 3500XT-P1 | 3500XT-P1-LT | 3400XT-P2 | 3500XT-P2 | 3500XT-P2-LT

Parallel Applications | easYgen | GC-3000XT

Woodward’s easYgen | GC-3400XT group controller is designed to manage virtually any large scale power generation system you can imagine. It enables you to command up to 248 gensets, with complete genset management, synchronization, dead bus prioritization, load share, and load dependent start/stop capabilities, in combination with Woodward’s easYgen-3400XT/3500XT equipped genset controllers. These controllers come with standardized software that is simple to configure, yet easily customizable for individual applications. Peer-to-peer communication between the controls and load share line redundancy at each level ensures single-fail-safe operation of your power generation control system.

Источник

Genset Controllers

Genset controls for your power generation systems

Woodward offers a wide range of controllers for the generator set market. We strive to reduce total installed/operating cost and commissioning time while improving availability, efficiency, reliability and longevity.

We have the longest legacy of any controls supplier in the paralleling genset control market. We continuously invest in innovative solutions to real market problems and provide value to our original equipment manufacturers (OEMs), genset packagers, switchgear builders, system integrators and end user customers. Our knowledge of controls, auxiliaries and power generation systems lets us drive optimization through simplification and standardization.

Woodward provides fast response, local, knowledgeable support, and optimized, cost-effective solutions to our customers through our direct sales force as well as through our vast network of distributors. As an independent company, we are able to provide full service, support and upgrades for our current and legacy product lines.

Parallel Applications | easYgen-3000XT Series

The easYgen-3000XT Series controllers operate gensets of all sizes and applications. These controllers include specifically designed algorithms and logic to start, stop, control, and protect the genset, circuit breaker, and the utility where applicable. This technology allows standardizing on a single, affordable genset controller for distributed power generation applications. These applications can range from single stand-alone emergency backup power to parallel load sharing of multiple gensets in complex, segmented distribution systems with multiple utility feeds and tie breakers.

3100XT-P1 | 3200XT-P1 | 3200XT-P1-LT | 3400XT-P1 | 3500XT-P1 | 3500XT-P1-LT | 3400XT-P2 | 3500XT-P2 | 3500XT-P2-LT

Parallel Applications | easYgen | GC-3000XT

Woodward’s easYgen | GC-3400XT group controller is designed to manage virtually any large scale power generation system you can imagine. It enables you to command up to 248 gensets, with complete genset management, synchronization, dead bus prioritization, load share, and load dependent start/stop capabilities, in combination with Woodward’s easYgen-3400XT/3500XT equipped genset controllers. These controllers come with standardized software that is simple to configure, yet easily customizable for individual applications. Peer-to-peer communication between the controls and load share line redundancy at each level ensures single-fail-safe operation of your power generation control system.

Источник

Adblock
detector

Цифровые панели Power Wizard

Read Online >> Read Online Fg wilson genpart 6000 manual

P300 — P880E. 6000мм. P850 — P2200E. 2500мм. 1200мм и системами могут испытать обратной передачи в положении «MANUAL», таймер обратной. Below you will find our Operator & Maintenance Instruction Manual available for download, the manual provides comprehensive instructions and guidance on Very good condition Perkins generator built by FG Wilson. Model P800 capable of 800 kVA Panel & Circuit Breaker. Genpart 6000 Autostart control system with battery isolator, battery charger and jacket water heater. Manual circuit breaker: Search in FG WILSON catalogs and technical brochures on DirectIndustry and find the information you need in 1 click. design and validate FG Wilson control systems to optimise your generator set performance and put .. 4 Manual switch operation possible via external handle.When the 6000 series panel is configured as Engine speed adjust — manual and automatic FG Wilson has manufacturing facilities in the following locations:. All FG Wilson control panels are compact, versatile and easy to use. .. recognised symbols, eliminating the need for complex instructions or language settings. 9 Jul 2015 FG Wilson Generator Set. Operator & Maintenance. Instruction Manual. This manual has been designed as a guide to operators to aid in Its a containerised Fg Wilson generator. Engine is a perkins 3000 series V style. 500KVA Control module is a genpart 6000 (Never encountered this style of module) Could I manually start by engaging the rotary switch ?

http://newyorkundergroundradio.ning.com/photo/albums/horstmann-room-thermostat-t50-manual http://bmwclubng.com/forums/topic/cpa-study-guide/ http://property.ning.com/photo/albums/ottlite-manual http://www.stlramscfl.com/photo/albums/1-99-thieving-guide-moto http://newyorkundergroundradio.ning.com/photo/albums/function-of-nozzle-guide-vanes http://www.stlramscfl.com/photo/albums/evenflo-symphony-65-e3-all-in-one-convertible-car-seat-manual http://www.stlramscfl.com/photo/albums/summer-rite-hexangular-gazebo-instructions http://www.stlramscfl.com/photo/albums/the-twilight-saga-breaking-dawn-part-2-parents-guide http://www.stlramscfl.com/photo/albums/writing-business-requirementssportsman-guide-online-catalog

http://www.st