5
SPECIAL SAFETY INSTRUCTIONS FOR CHAIN SAW
zKeep all parts of the body away from the saw chain when the chain saw is operating. Before you
start the chain saw, make sure the saw chain is not contacting anything. A moment of
inattention while operating chain saws may cause entanglement of your clothing or
body with the saw chain.
zAlways hold the chain saw with your right hand on the rear handle and your left hand on the front
handle. Holding the chain saw with a reversed hand configuration increases the risk of
personal injury and should never be done.
zWear safety glasses and hearing protection. Further protective equipment for head, hands, legs
and feet is recommended. Adequate protective clothing will reduce personal injury by
flying debris or accidental contact with the saw chain.
zDo not operate a chain saw in a tree. Operation of a chain saw while up in a tree may result
in personal injury.
zAlways keep proper footing and operate the chain saw only when standing on fixed, secure and
level surface. Slippery or unstable surfaces such as ladders may cause a loss of balance or
control of the chain saw.
zWhen cutting a limb that is under tension be alert for spring back. When the tension in the
wood fibres is released the spring loaded limb may strike the operator and/or throw the
chain saw out of control.
zUse extreme caution when cutting brush and saplings. The slender material may catch the
saw chain and be whipped toward you or pull you off balance.
Carry the chain saw by the front handle with the chain saw switched off and away from your body.
When transporting or storing the chain saw please always fit the guide bar cover. Proper handling
of the chain saw will reduce the likelihood of accidental contact with the moving saw chain
.
zFollow instructions for lubricating, chain tensioning and changing accessories. Improperly
tensioned or lubricated chain may either break or increase the chance for kickback.
zKeep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery
causing loss of control.
zCut wood only. Do not use chain saw for purposes not intended. For example: do not use chain
saw for cutting plastic, masonry or non-wood building materials. Use of the chain saw for
operations different than intended could result in a hazardous situation.
Causes and Operator Prevention of Kickback
Kickback may occur when the nose or tip of the guide bar touches an object, or when the
wood closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up
and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back
towards the operator.
Either of these reactions may cause you to lose control of the saw which could result in
serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As
a chain saw user, you should take several steps to keep your cutting jobs free from accident
View the manual for the Sovereign YT4334-01 here, for free. This manual comes under the category saws and has been rated by 1 people with an average of a 9.1. This manual is available in the following languages: English. Do you have a question about the Sovereign YT4334-01 or do you need help? Ask your question here
Can’t find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Sovereign YT4334-01 below.
What is the best way to clean my saw blade?
1. Wipe sawdust from the saw blade with a brush. 2. Spray the saw blade with oven cleaner and leave for 30 minutes. 3. Remove the oven cleaner and dirt with a dry cloth. 4. Grease saw blade with Vaseline.
My saw blade is blunt. What now?
If there is resin or other debris on the blade, it may look like the blade is blunt. If the saw blade has been thoroughly cleaned and is still blunt, it is recommended to have the saw blade sharpened.
How do I remove rust from my Sovereign saw?
1. Soak the rusty part in vinegar until completely soaked through. 2. Let the vinegar work on the rust for 24 hours. 3. Remove the rust with a wire brush or aluminium foil.
What does ’16V’ or ’20V’ mean?
The maximum achievable charge level is expressed with 16V or 20V. The V in this case stands for Volt.
Do I have to wear hearing protection when using a saw?
The amount of sound varies a lot per brand and type of saw, it is therefore wise to wear hearing protection to be sure.
Is the manual of the Sovereign YT4334-01 available in English?
Yes, the manual of the Sovereign YT4334-01 is available in English .
Is your question not listed? Ask your question here
3.0
Rated 3.0 out of 5
3.0 out of 5 stars (based on 1 review)
Your overall rating
SOVEREIGN YT4334-01 (01) PDF MANUAL
Click here to download SOVEREIGN YT4334-01 (01) PDF MANUAL
SOVEREIGN YT4334-01 (01) PDF MANUAL
FREE ENGLISH PDF
OPERATING INSTRUCTIONS
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL
Your overall rating
- YouTube
SOVEREIGN YT4334-01 (01) PDF MANUAL
SOVEREIGN YT4334-01 (01) PDF MANUAL
Цвет на изображении может отличаться от действительного рисунка.
4 411 ₽
Цена за 1 шт.
Самовывоз в пятницу 08 декабря после 15:00.
Доставка в Москве, отправка возможна в воскресенье 10 декабря после 18:00. Стоимость доставки до ТК 499 руб.
Как купить дешевле?
VK
FB
Telegram
Pin
OK
Другие варианты покупки
Технические характеристики Пила электрическая YT4334, 1800 Вт
| Вес, кг | 5.25 |
| Напряжение (В) | 220-240 |
| Функция | Нарубить поленья среднего сечения |
| Мощность (Вт) | 1800 |
| Диаметр реза (см) | 36 |
| Объем масляного бака (л) | 0.1 |
| Расстояние между зубцами (мм) | 4 |
| Длина сетевого кабеля (м) | 0.25 |
| Уровень звукового давления (дБ) | 108 |
| Антивибрационная система | Нет |
| Способ натяжения цепи | С помощью инструмента |
| Шаг цепи | 3/8″ |
| Наименование товара | Цепная пила |
| Гарантия (лет) | 0.5 |
| Цветовая палитра | Жёлтый / золотой| Черный |
| Основной материал | Сталь |
| Страна производства | Китай |
| Частота использования | Нерегулярный |
| Длина направляющей (см) | 36 |
| Тип упаковки | Коробка |
| Тип продукта | Цепная пила электрическая |
| Страна-производитель | Китай |
| Ценник | Обычная цена |
| Вес нетто (кг) | 5.09 |
| Тип двигателя | Уголь |
| Маслонасос | Да |
| Максимальная частота вращения двигателя (об/мин) | 8580 |
| Тип смазки | Автоматическая подача масла |
| Тип продукта | Электрический |
| Вес товара в индивидуальной упаковке (кг) | 5.25 |
| Ширина индивидуальной упаковки товара (см) | 20 |
| Высота индивидуальной упаковки товара (см) | 26 |
| Глубина индивидуальной упаковки товара (см) | 50 |
| Кол-во коробок в поставке | 1 |
| Телескопическая ручка | Нет |
| Тип направляющей | С колесиками |
| Индикатор уровня масла | Да |
| С термозащитой | Нет |
| Скорость цепи (м/с) | 14.5 |
| Индикатор питания | Нет |
| Количество звеньев | 52 |
| Датчик наполнения | 1.3 |
| Видимый при осмотре | Да |
| Сделано во Франции | Нет |
| Произведено в Европейском Союзе | Нет |
| Специфический режим прямой доставки | Нет |
| Название цвета | Жёлтый / золотой| Черный |
| Короткое наименование товара для клиента | Пила эл YT4334 1800Вт |
| Марка шины | KANGXIN |
| Диаметр отверствия под ось (мм) | 4.5 |
| Материал | Сталь |
| Метка сортировки | Нет |
| Содержит древесину | Нет |
| Топ 1000 ADEO | Да |
| Тип AEE | Нет |
| Язык инструкции | Английский| Французский |
| Язык упаковки | Английский| Французский| Греческий| Итальянский| Польский| Португальский| Румынский| Русский| Испанский| Украинский |
| Прирост высоты штабелируемых товаров (%) | 100 |
| Политика ценообразования (LMPL) | Другие товары |
| Толщина соединительной пластины (мм) | 1.27 |
| Марка цепи | KANGXIN |
Отзывы пользователей о Пила электрическая YT4334, 1800 Вт
Отзывов на данную модификацию пока нет.
Рекомендуем аналогичные товары