| Document’s Content and Additional Information | Share Manual |
|---|---|
|
Zubler VARIO PRESS 300 Operation instructions manual
Pages Preview: Document Transcription:
See Details |
|
|
Zubler VARIO PRESS 300 Operation instructions manual
See Details |
(2) Zubler VARIO PRESS 300 Stove User Manuals and Instructions
Stove:
More Instructions:
- Z1-M
- V40PRO
- Condensing Oil-Fired Furnace
- VARIO 200
- VARIOstar Series
- SMARTtorque S609 C
- 080
- VARIO PRESS 300.e
- Z1 ECO
Related Manuals for Zubler VARIO PRESS 300:
Categories of Zubler Devices:
Medical Equipment
Dental equipment
Scales
Furnace
Stove
Vacuum Cleaner
 |
[Page 1] Zubler VARIO PRESS 300 innovative dental products www.zubler.de Operation Instructions 01 2014 / Rev. 1 USB VARIO PRESS ® 330000 VARIO PRESS ® 330000 . e en 230/240 |
 |
[Page 2] Zubler VARIO PRESS 300 Intentionaly blank |
 |
[Page 3] Zubler VARIO PRESS 300 3 Page Contents 0. Introduction Page 4 0.1 Statement of compliance 0.2 General 0.3 Setting up the furnace Page 6 0.4 Basic Settings 0.5 Use within specifications 0.6 Hints for your safety 1. Main menu Page 12 1.1 Run programs 1.2 Edit programs 1.2.1… |
 |
[Page 4] Zubler VARIO PRESS 300 4 Page 0.2 General The correct processing of modern dental ceramic materials is placing even higher demands on dental technicians. We believe that the VARIO 330000 furnaces meet these requirements by providing the latest technology for current and… |
 |
[Page 5] Zubler VARIO PRESS 300 To furnace “air” Compressed air supply 0.6MPa Pressure unit in out 5 Page Compressed air connection The smaller of the white boxes contains the accessories needed for the com- pressed air connection. Use the two screws provided to connect the pre… |
 |
[Page 6] Zubler VARIO PRESS 300 6 Page 0.5 Use within specifications Caution The VARIO PRESS ® 330000 / VARIO 330000 furnace series was exclusively designed for firing and/or pressing dental ceramics. The user is liable for all damages resulting from usage other than that spe… |
 |
[Page 7] Zubler VARIO PRESS 300 7 Page ✗ ✗ ! ■ During operation never place your hand between the lift table and the furnace chamber. There is a risk of pinching your hand and a burn hazard. ■ During operation never place your hand under the furnace table and do not put an … |
 |
[Page 8] Zubler VARIO PRESS 300 8 Page ATTENTION Safety warnings ! Never put any potentially flammable materials such as paper, brushes or similar things, as well as easily flammable substances like alcohol, insulation sprays or die spacers close to the furnace. 0.6 Notes for your … |
 |
[Page 9] Zubler VARIO PRESS 300 9 Page ■ Leave at least 8” – 12” of free space around and above the unit. Adjacent structures surrounding the unit should be non-flammable and the area should be well-ventilated. ■ Follow fire department guidelines, always store a multi-pur… |
 |
[Page 10] Zubler VARIO PRESS 300 10 Page ■ Hoses and connections should be checked periodically for fit, wear and damage and replaced or tightened, as needed. ■ All cords and hoses should be located away from walkways and aisles. ■ During certain operations, such as high-tempe… |
 |
[Page 11] Zubler VARIO PRESS 300 11 Page Muffle Dust Exposure This furnace contains respirable refrac- tory ceramic fibers (RCF) and crystalline silica in its thermal muffle insulation. These materials may be in the form of fiber blanket or felt, vacuum formed board or shapes… |
 |
[Page 12] Zubler VARIO PRESS 300 12 Page Main menu 1. — + Selection of menu parameters ❶ Once you have switched on the oven, the Main Menu will appear on the dis- play with the following five items: 1.1 Run programs 1.2 Edit programs 1.3 Setup oven 1.4 Run warm-up program 1.5 Sta… |
 |
[Page 13] Zubler VARIO PRESS 300 13 Page Enter Esc Up Down 2 — Pulse MC Ceramay 450°C Select program … 40- PULSE MC OPAQUE 1+2 41- PULSE MC MARGIN 1 42- PULSE MC MARGIN 2 43- PULSE MC DENTIN 1 44- PULSE MC DENTIN 2 45- PULSE MC SHADE/STAIN 46- PULSE MC GLAZEFIRING 47- PULS… |
 |
[Page 14] Zubler VARIO PRESS 300 14 Page Overwriting a program during operation Should you find that you have to tem- porarily change one or more parameters while a program is running, you can do this by pressing the yellow “Edit Prog.” key below the display. In general, you can… |
 |
[Page 15] Zubler VARIO PRESS 300 15 Page Enter Esc Enter Esc 2 — Pulse MC Ceramay 450°C Select program … 2 — Pulse MC Ceramay 450°C Select Brand … Next Up Down 40- PULSE MC OPAQUE1+2 41- PULSE MC MARGIN 1 42- PULSE MC MARGIN 2 43- PULSE MC DENTIN 1 44- PULSE MC DENT… |
 |
[Page 16] Zubler VARIO PRESS 300 16 Page 1.2 Edit Program Enter Esc Edit Programs 450°C New / Change program Copy / Change program Move program Erase program Look at program New / Change Brand Erase Brand CF transfer Enter Esc Left Right 2-Pulse MC Ceramay 450 C° … |
 |
[Page 17] Zubler VARIO PRESS 300 17 Page Enter Esc 2 — PULSE MC CERAMAY 400C EDIT 43-PULSE MC DENTIN 1 Program type Professional -Start temp 450C -Pre dry Yes -Pre dry time 3:00 -Closing time 3:00 -Soak temp 450C -Soak time 0:30 -Heat rate 55C -Final temp 820C -Hold t… |
 |
[Page 18] Zubler VARIO PRESS 300 18 Page ❶ The Professional Program Start temperature Temperature in the firing chamber at which the program starts. Pre-dry Selecting “YES” activates the special pre-drying program. Pre-dry time Enter a time. In this section, the lift identifie… |
 |
[Page 19] Zubler VARIO PRESS 300 19 Page ➋ The Standard Program Start temperature Temperature in the firing chamber at which the program starts. Pre-dry Selecting “YES” activates the special pre-drying program. Pre-dry time Enter a time. In this section, the lift identifies a … |
 |
[Page 20] Zubler VARIO PRESS 300 20 Page ➌ The Special Program (Firing Program with two heeting rates, e.g. crystallization for IPS e.max ® CAD) Start temperature Temperature in the firing chamber at which the program starts. Pre-dry Selecting “YES” activates the special pre-… |
 |
[Page 21] Zubler VARIO PRESS 300 21 Page Enter Esc Main menu1. 2 — PULSE MC CERAMAY 450C Edit 56-PULSE PTM 200/2 Program type I-Press -Start temp 700C -Heat rate 60C -Final temp 920C -Hold time 20:00 -Extra press time 0:00 -Max press time 10:00 -Pressure Low -Vacuum level 720… |
 |
[Page 22] Zubler VARIO PRESS 300 22 Page Enter Esc 8 — IN — CERAM VITA 400°C Edit 163-AL.SINTER BRIDGE Program type Sinter -Start temp 30C -Time rise 1 Hr:Mn 6:00 -Temp 1 120°C -Hold time 1 Hr:Mn 0:00 -Time rise 2 Hr:Mn 2:00 -Temp 2 1120°C -Hold time 2 Hr:Mn … |
 |
[Page 23] Zubler VARIO PRESS 300 23 Page Main menu 1. Esc Enter 1 0 °C 450 500 550 600 650 700 750 800 850 900 950 1000 1100 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 bar 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 19 20 min 1050 Time [min] Pressure [bar] Temperature [°C] Firing cham… |
 |
[Page 24] Zubler VARIO PRESS 300 24 Page 1.2.2 Copy/change program ■ Copy from: select the program to be copied using the dialer or the +/- keys. ■ By pressing the green “Enter” key, you can confirm the program selected for duplication. ■ You now return to the brand page. … |
 |
[Page 25] Zubler VARIO PRESS 300 25 Page Enter Esc Left Enter Esc Edit Programs 400C New / Change program Copy / Change program Move program Erase program Look at program New / Change Brand Erase Brand CF transfer Right New / Change Brand 400C Enter Name … 2 — PULSE MC CERAMAY 1.2… |
 |
[Page 26] Zubler VARIO PRESS 300 26 Page 1.2.8 USB — transfer For loading or storing programs on the USB, you need a USB flash drive with USB Microsoft protocol and a folder named, «VARIO». ■ In the “Edit Programs” Menu select USB-Transfer using the + / -keys or the… |
 |
[Page 27] Zubler VARIO PRESS 300 27 Page 1.3 Set-up oven User can enter their individual require- ments here. The following table depicts the individual settings, together with their impact on the function of the ceramic furnace. 1.3.1 Idle temperature This is a temperature reache… |
 |
[Page 28] Zubler VARIO PRESS 300 Abort Night mode 445C 445C Warning recommendation: The 1st. program initiated after “night mode” should be the warm-up program. 28 Page 1.5 Start “night mode” Instead of switching the furnace off, use night mode to prevent moisture and con… |
 |
[Page 29] Zubler VARIO PRESS 300 Filter Locking screw 29 Page Maintenance 2. F1 F2 F3 Filter for compressed air 501/0084 Filter for vacuum pump 556 / 072 Pressing tray 898 / 108 Insert for pressing tray 898 / 109 Firing tray 898 / 110 Long tweezers 898 / 106 Ring forceps 898 / 4136… |
 |
[Page 30] Zubler VARIO PRESS 300 30 Page Technical Data3. VARIO 330000 VARIO 330000 Width x depth Height Weight Voltage Current Performance Data: Idle temperature Temperature Color display Programs Pressing pressure low high Width x depth Height Weight Voltage Current Vacuum … |
 |
[Page 31] Zubler VARIO PRESS 300 31 Page 3.1 Scope of supply VARIO PRESS ® 330000 1x Power cord 1x Operating system CF — card (green) 1x Ring tong 1x Firing tray 1x Pressing tray incl. press insert 1x Compressed air hose 2m (blue) 1x Pressure reducer (water strainer) with fixing … |
 |
[Page 32] Zubler VARIO PRESS 300 32 Page Service4. Zubler Gerätebau GmbH Buchbrunnenweg 26 89081 Ulm-Jungingen Phone: +49(0)731-14520 Fax: +49(0)731-145213 Mail: [email protected] www.zubler.de If more help is needed We hope you will have many years of trouble-free service from your … |
 |
[Page 33] Zubler VARIO PRESS 300 33 5.1 Press Programs* I-Press Program Authentic 100g ring Authentic 200g ring Pulse press-to-metal ® 200g ring / 2g Pellet Pulse press-to-metal ® 200g ring / 5g Pellet Pulse press-to-metal ® 300g ring / 2g Pellet Pulse press-to-metal ® 300g rin… |
 |
[Page 34] Zubler VARIO PRESS 300 34 Program examples Professional Mode Page 5. 5.2 Firing Programs* Authentic ® 450 yes 3:00 3:00 450 0:30 55 845 1:00 — — 845 0:00 yes Heat-up 845 450 yes 3:00 3:00 450 0:30 55 950 1:00 — — 950 0:00 yes Heat-up 950 450 yes 3:00 3:00 450 0:30 … |
 |
[Page 35] Zubler VARIO PRESS 300 35 Program examples Professional Mode 5.2 Firing Programs* Pulse ® MC / Pulse ® MC 3-16 450 yes 3:00 3:00 450 0:30 80 950 1:00 — — 950 0:00 yes Heat-up 950 450 yes 3:00 3:00 450 0:30 55 880 1:00 — — 880 0:00 yes Heat-up 880 450 yes 3:00 3:0… |
 |
[Page 36] Zubler VARIO PRESS 300 36 5.2 Firing Programs* Pulse ® ZR / Pulse ® ZR 3-16 Professional Mode Page 450 yes 2:00 2:00 450 0:30 45 970 1:00 — — 970 0:00 yes Heat-up 970 450 yes 3:00 3:00 450 0:30 45 770 1:00 — — 770 0:00 yes Heat-up 770 450 yes 3:00 2:00 450 0:30 45… |
 |
[Page 37] Zubler VARIO PRESS 300 37 Professional Mode 5.2 Firing Programs* Ivoclar InLine 403 yes 3:00 3:00 450 0:30 100 930 2:00 — — 930 0:00 yes Heat-up 930 403 yes 2:00 2:00 450 0:30 60 930 1:00 — — 930 0:00 yes Heat-up 930 403 yes 2:00 2:00 450 0:30 60 910 1:00 — — 910… |
 |
[Page 38] Zubler VARIO PRESS 300 38 Professional Mode Page 5.2 Firing Programs* Ivoclar e.max ceram 403 yes 3:00 3:00 450 0:30 100 940 2:00 — — 940 0:00 yes Heat-up 940 403 yes 3:00 3:00 450 0:30 100 930 2:00 — — 930 0:00 yes Heat-up 930 403 yes 2:00 2:00 450 0:30 60 960 1:0… |
 |
[Page 39] Zubler VARIO PRESS 300 39 403 — 6:00 550 0:00 90 820 0:10 30 840 7:00 700 7:00 403 — 6:00 550 0:00 60 770 0:10 30 850 10:00 700 10:00 403 — 6:00 550 0:00 90 820 0:10 30 840 3:00 700 3:00 403 — 0:18 403 0:00 65 1050 15:00 — — — 750 — —no no Special Mode Special Mod… |
 |
[Page 40] Zubler VARIO PRESS 300 40 Professional Mode Page Professional Mode 5.2 Firing Programs* Vita VM 13 500 yes 1:00 1:00 500 0:30 75 890 2:00 — — 890 — yes Heat-up 890 500 yes 2:00 2:00 500 0:30 75 890 2:00 — — 890 — yes Heat-up 890 500 yes 1:00 1:00 500 0:30 75 890 … |
 |
[Page 41] Zubler VARIO PRESS 300 41 5.2 Firing Programs* Ceramco 3 500 no 0:00 1:00 500 0:00 55 ** ** — — ** ** ** ** ** 500 yes 4:00 2:00 500 0:30 100 975 0:00 — — 975 0:00 yes Heat-up 975 650 yes 3:00 2:00 650 0:30 70 970 0:00 — — 970 0:00 yes Heat-up 970 650 yes 5:00 4:00 … |
 |
[Page 42] Zubler VARIO PRESS 300 42 Professional Mode Page 5.2 Firing Programs Name: Oxide Powder opaque Paste opaque 1 Paste opaque 2 Margin 1 Margin 2 Dentin 1 Dentin 2 Glaze with vac. Glaze no vac. Stains Correction Start Pre Pre Closing Soak Soak Heat Final Hold Temper Temper Op… |
 |
[Page 43] Zubler VARIO PRESS 300 43 6. Important notes for the processing of Lithium Disilicate VARIO PRESS 300.e 6.1 Investment ■ Recommended investment with respective quantity of liquid: • Zubler HS-PC 25ml total liquid on 100g powder „Speed investing“: ■ The process… |
 |
[Page 44] Zubler VARIO PRESS 300 44 Page 44 6. Important notes for the processing of Lithium Disilicate VARIO PRESS 300.e 6.4 Investing Pay attention to the attached brochure re- garding the VARIO BALANCE dosing device. ■ The mixing bowl should be moist. ■ Choose the desired con… |
 |
[Page 45] Zubler VARIO PRESS 300 4545 6. Important notes for the processing of Lithium Disilicate VARIO PRESS 300.e Z PC — for Zubler HS-PC I PV… — for PressVest (Ivoclar) Single — for Single parts Bridge — for bridges or blocked parts 100 — for 100g ring 200 — for 200g rin… |
 |
[Page 46] Zubler VARIO PRESS 300 46 Page 46 6. Important notes for the processing of Lithium Disilicate VARIO PRESS 300.e 6.7 Divesting Always follow the manufacturer’s instructions. For e.max, follow Ivoclar’s recommendations. ■ Separate the ring with a cutoff wheel at… |
 |
[Page 47] Zubler VARIO PRESS 300 Intentionaly blank |
 |
[Page 48] Zubler VARIO PRESS 300 48 Page innovative dental products Zubler Gerätebau GmbH Buchbrunnenweg 26 D-89081 Ulm-Jungingen Phone +49(0)731-14 52 0 Fax +49(0)731-14 52 13 www.zubler.de C press-to-metal is a registered Trademark of Zubler Gerätebau GmbH VARIO BALANCE Dosage d… |
 |
[Page 49] Zubler VARIO PRESS 300 49 Page Note: Main menu1. |
Zubler Vario Press 300e — печь для обжига и прессования керамики в комплекте с вакуумной помпой | Zubler (Германия)
Производитель: Zubler
Код Товара: S-7953
Артикул: S-7953
Наличие: В наличии
526068.00руб.
Описание Zubler Vario Press 300e — печь для обжига и прессования керамики в комплекте с вакуумной помпой | Zubler (Германия)
Печь Vario Press 300e для обжига и прессования керамики c технологией прессования Е.МАХ Zubler ADVANCED PRESS
Статья по теме – Обзор печи для обжига и прессования керамики Zubler Vario Press 300e
Преимущества:
- Воспроизводимые результаты обжига
- Индивидуальный процесс обжига
- Долговечные результаты постоянного качества
- Сегодняшняя технология печи, которая будет важна в будущем
- Легкость в использовании
- Многофункциональность (обжиг, прессование, синтеризация)
- Возможность работать со всеми видами керамики, имеющейся на рынке
- Цена
Технические характеристики:
Vario Press
- Ширина х глубина: 360 мм x 430 мм
- Высота: 765 мм
- Вес: 26 кг
- Напряжение: 230 В/50 Гц
- Ток: 7A макс. вкл. насос
- Предварительный нагрев: 80°C — 660°C
- Интервал нагрева: 20°C- 1200°C
- Цветной дисплей 120 мм x90 мм, 320 x 240 точек на дюйм
- Программы: 500
- Давление прессования:
- Низкое: 3,2 бар
- Высокое: 5,0 бар
Вакуумный насос P3
- Ширина х глубина: 320 ммx186 мм
- Высота: 275 мм
- Вес: 12 кг
- Напряжение: 120 В/60 Гц
- Ток: 1.75A
- Вакуум макс: 985 мбар
Комплектация:
- 1x Шнур питания
- 1x Инструкция по эксплуатации
- 1x Карта флэш-памяти формата Compact Flash
- 1x Система гибких колец Flex ring 200 г
- 1x Столик для обжига
- 1x Прессовочный столик, включая пресс-подставку
- 1x Шланга для сжатого воздуха – длина 2 метра (синий)
- 1x Редуктор давления (водяной фильтр) с крепежным кронштейном.
- 1x Длинные щипцы
- 1x Пинцет
- 1x Вакуумный шланг
- 1x Шнур для подключения вакуумного насоса P3.
- 1x Вакуумный насос Р3
Брошюра VARIO PRESS 300e
Инструкция VARIO PRESS 300e
| Характеристики | |
| Вес упаковки | 26.00 кг |
| Габариты упаковки (Д x Ш x В) | 430.00 мм x 360.00 мм x |
| Код товара | S-7953 |
- Company
- Products
- Catalogs
- News & Trends
- Exhibitions
VARIO PRESS 300
46Pages
Catalog excerpts
0.1 Statement of compliance 0.2 General 0.3 Setting up the furnace Page 6 0.4 Basic Settings 0.5 Use within specifications 0.6 Hints for your safety 1.3.1 Change idle temperature 1.3.2 Change night temperature 1.3.4 Vacuum pump operation 1.3.6 Diagnostic tests O Run pre-heat/dry program © Run purge program © About version © Update software © Service tests 1.5. Start night mode Page 28 2.2 Filter element for compressed air supply 2.3 Filter element for vacuum pump processing of Lithium Disilicate VARIO PRESS 300.e 6.1 Investment It is critical that the user completely read the…
Open the catalog to page 3
Conformity Declaration Zubler Geraetebau GmbH Buchbrunnenweg 26 89081 Ulm-Jungingen, Germany www.zubler.de The correct processing of modern dental ceramic materials is placing even higher demands on dental technicians. We believe that the VARIO PRESS 3 00 furnaces meet these requirements by providing the latest technology for current and future ceramic processing. In the event that the packaging materials and/or the ceramic furnace appear to have been damaged contact your dealer (see Page 32) immediately and do not unpack the product. hereby declare, that the ceramic furnace product VARIO…
Open the catalog to page 4
Compressed air connection The smaller of the white boxes contains the accessories needed for the compressed air connection. Use the two screws provided to connect the pressure regulator vertically to the housing of the vacuum pump or secure it elsewhere in the laboratory in the immediate vicinity of the furnace. Measure the distances from the compressed air supply to the pressure regulator and from the pressure regulator to the ceramic furnace. Split the blue compressed air hose into two lengths of hose accordingly. Use one part of the blue compressed air hose to connect the output…
Open the catalog to page 5
0.4 Basic settings Once you have turned on the device, and the firing or pressing tray has been put in, you can enter the basic settings. The oven will prompt you to enter a few basic settings in preparation for use. Please enter the following: Main menu == additional settings == basic settings = Enter 2. Set the night mode temperature 6. Activate the parameter preview „yes» or„no» 7. After completing the basic settings the furnace automatically runs a drying program, to remove any possible residual moisture resulting from transportation or storage (duration approx. 20 min.) 8. Once the…
Open the catalog to page 6
I Use the special cooling grid to cool the investment ring after a pressing process. I Please unpack the oven with caution. The oven should always be carried by two persons. Always lift the device at the bottom, never at the furnace chamber or table slide bar. I The oven must always have a firing or pressing brick on the lift table. I A furnace with a pressing function must always be conneced to compressed air, even during normal vacuum firing, so the pressing plunger remains “up” in its starting position. I During operation never place your hand between the lift table and the furnace…
Open the catalog to page 7
0.6 Notes for your Safety ■ Side port cover on the side of the furnace should always remain closed. ■ The oven must be turned off before removing or inserting the USB stick. ■ The air vents must be kept free from obstruction and clean at all times to allow proper air circulation. If this is not done, there is a risk of overheating the furnace. Conflict ■ Make sure that no liquids or other foreign objects enter the furnace or the air vents, as this may result in an electrical shock. Conflict ■ The lift of the furnace has an electrical lift drive and has to be operated by the «Open» and…
Open the catalog to page 8
■ Use this furnace only for its intended purpose as described in this Owner’s Manual and carefully remove all packing materials and tape during installation. ■ The furnace may only be used indoors. ■ Materials developing harmful gases must not be processed in this furnace. ■ This furnace must be plugged into a properly grounded circuit. If you have questions regarding the proper circuit, contact a licensed electrician. ■ Any disruption of the protective conductor, either inside or outside the furnace, or any loosening of the protective conductor connection may lead to danger for the user in…
Open the catalog to page 9
■ Be sure that the furnace is properly installed per our instructions and that the selected electrical outlet is properly grounded. ■ The electrical service provided must be a dedicated line of the proper size according to local electrical codes. Consult a qualified electrician to ensure that your amperage is sufficient to prevent burdening of any existing circuit. ■ Do not use an extension cord with the furnace. Check with your utility provider for electrical codes, which apply in your area. ■ In case of undervoltage, the temperature increase may be delayed. ■ Compressed air systems must…
Open the catalog to page 10
■ In case of a service, use only original spare parts. ■ Unauthorized changes or modifications to hardware or software can create severe safety hazards, as well as terminate your warranty. ■ Children and untrained visitors should never be left alone or unattended in the area where a furnace is in use. They should never be allowed to climb or stand on any surface, where the furnace is situated and being operated from. Items of interest to children should not be stored in and around the furnace. Children climbing on and around the surface where furnace operates could be seriously injured. ■…
Open the catalog to page 11
Main menu Selection of menu parameters Display functions Once you have switched on the oven, the Main Menu will appear on the display with the following five items: 1.1 Edit programs Setup oven Start night mode Oven type Circle dialer Current temperature MAIN MENU 450°C Run Programs Edit Programs Setup Oven Run warm-up program Please select your desired menu parameters using the dialer or the +/- keys Start night mode Confirm your selection with the green “Enter” key Enter Section for selecting parameters Confirm / cancel key Lift movement Up/Down Section for changing values Rapid selection…
Open the catalog to page 12
