Tylo печь для сауны инструкция

INSTRUCTIONS FOR USE 

CC 10 

Functions. 

1 = setting scale. 2 = time settings. 3 = temperature settings. 4 = on. 5 = off. 
6 = lighting. 

Dip-switch. 

See page 17.

Illumination. 

The illumination automatically switches on when the unit starts and switches off 
automatically when the unit shuts down. You can also switch the illumination on or off 
manually by pressing LIGHT. 

Temperature setting. 

(The heater must be switched on) 
Press TEMP – the previous temperature setting is displayed. 
The numbers indicate a rising temperature scale. Experiment to find the temperature 
that suits you best. Begin for example by turning the thermostat dial to position 4. If 
you later find that you would prefer a higher or lower temperature, adjust the dial up 
or down until you find the ideal bathing temperature for you (usually 70-90°C (158-
194°F) for traditional dry and wet sauna baths, 40-45°C (104-113°F) for steam 
saunas and herb saunas). 

Manual on/off. 

Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out). 
A memory function automatically sets the previous temperature. 
Press TEMP – to change the pre-set temperature. 
The built-in timer automatically switches the sauna heater/steam generator off after 
3 hours. If you want to switch it off earlier than that, press OFF. To extend the sauna 
time, press ON. 

Timer settings. 

(The heater must be switched off) 
The numbers in this case represent the timer times (= the number of hours until the 
heater automatically switches on). To set the timer: 
Press TIME – use the arrow keys to select the desired pre-set time, 1–10 hours. 
Press ON – the timer is activated and the time indicator blinks during the pre-set 
time period. Once the heater switches itself on, it remains on for 3 hours, after which 
it automatically switches itself off. If you want to switch it off earlier than that, just 
press OFF. To extend your sauna time, press ON. 

Main power switch. 

To be changed more than once: At the bottom of the relay box, the SE unit and the 
smaller types of steam generators is a main power switch that disconnects the 
heater entirely from the electrical supply. This main switch should only be used if the 
sauna will not be used for a longer period, such as several weeks. To be changed 
more than once: The memory function must be reset each time the power is 
interrupted. 

INSTRUCTIONS FOR USE 

CC 50 

00

1 

2 

3 

4 

6

Functions. 

1 = lighting. 2 = on/off. 3 = temperature setting. 4 = time setting. 5 = reduce temperature/time. 
6 = increase temperature/time. 7 = display. 

Lighting. 

Lights automatically when the facility starts and switches off automatically 
when the facility shuts down. You can also switch the lighting on or off 
manually by pressing LIGHT.Main power switch. 
To be changed more than once: At the bottom of the relay box, the SE unit and the 
smaller types of steam generators is a main power switch that disconnects the 
heater entirely from the electrical supply. This main switch should only be used if the 
sauna will not be used for a longer period, such as several weeks. The memory 
function is on even if the power is interrupted. 
The thermometer in the sauna/steam bath should be placed at such a height that the 
temperature corresponds exactly to the numbers in the panel of the CC 50. 

SETTINGS 

CC 50, all models 

Setting the bathing temperature. 

Press TEMP – the previous temperature is displayed. Use the up and down arrows 
(

 ) to change the temperature.

Manual on/off. 

Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out). If 
you forget to switch off the generator manually, it switches off automatically after 3 
or 12 hours — depending on the type of control panel. 

Timer settings. 

(The sauna must be switched off) 
Press TIME (the hour digits blink) – set the number of hours until you want to use 
the sauna using the up and down arrows (

 ). 

Press TIME (the minute digits blink) – set the number of minutes until you want to 
use the sauna using the up and down arrows (

 ). 

(Important: The hour or minute digits must be blinking before you press ON). 
Press ON – the on time is activated and a red LED blinks until the sauna 
automatically starts after the pre-set time. The heater switches off automatically 
after 3 or 12 hours – depending on the type of control panel. 
You can switch off the sauna manually at any time by pressing OFF. 
 

Changing the type of panel (

Factory settings = Test no. 50

), 

1.  Connect the voltage. 

2.  Press 

 and  at the same time for approx. 6 sek (max. 60 sek. after 

the voltage is connected). 

3.  Change the type of panel according to the scheme with 

 and , 

approve with TEMP. 

Panel type 

Test no. 

Description 

CC50-3B 

50 

Sauna 110°C, 3 h running time 

CC50-12B 

51 

Sauna 110°C, 12 h running time 

CC50-3S 

53 

Steam 55°C, 3 h running time 

CC50-12S 

54 

Steam 55°C, 12 h running time 

CC50-1S 

15 

Steam 55°C, 1 h running time 

CC50-1B 

18 

Sauna 110°C, 1 h running time 

CC50-24B 

58 

Sauna 110°C, 24 h running time 

CC50-0B 

59 

Sauna 110°C, ON/OFF 

CC50-24S 

68 

Steam 55°C, 24 h running time 

CC50-0S 

69 

Steam 55°C, ON/OFF 

At ev. use of extern switch the panel detects itself if it is with impulse or 
ON/OFF function. 

Code lock to prevent settings from being changed. 

First program as ”Settings”, press on the down arrow (

), hold it down and press 

TEMP and TIME at the same time. The code lock, which prevents changing of 
settings, is now activated. To return to unlocked mode, press the down arrow (

), 

hold it down and press OFF at the same time.

Code lock that prevents changing of the temperature setting. 

First program as ”Settings”, press TIME, hold it down and press TEMP and LIGHT at 
the same time. The code lock, which prevents changing of the temperature 
settings, is now activated. To return to unlocked mode, press the down arrow (

), 

hold it down and press OFF at the same time.

In the event of any problems, please contact the retailer 

where you purchased the equipment. 

© This publication may not be reproduced, in part or in whole, without the written permission of Tylö. Tylö 
reserves the right to make changes in materials, construction and design. 

3

INSTRUCTIONS FOR USE

10

9

8

7

6

5

4

3

2

1

1 2 3

Functions.

1 = setting scale. 2 = time settings. 3 = temperature settings. 4 = on. 5 = off.

Temperature setting.

(The heater must be switched on)

Press TEMP – the previous temperature setting is displayed.

The numbers indicate a rising temperature scale. Experiment to find the temperature

that suits you best. Begin for example by turning the thermostat dial to position 4. If you

later find that you would prefer a higher or lower temperature, adjust the dial up or down

until you find the ideal bathing temperature for you (usually 70-90° C (158-194° F) for

traditional dry and wet sauna baths, 40-45° C (104-113° F) for steam saunas and herb

saunas).

Manual on/off.

Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out).

A memory function automatically sets the previous temperature.

Press TEMP – to change the pre-set temperature.

The built-in timer automatically switches the sauna heater/steam generator off after

3 hours. If you want to switch it off earlier than that, press OFF. To extend the sauna

time, press ON.

Timer settings.

(The heater must be switched off)

The numbers in this case represent the timer times (= the number of hours until the

heater automatically switches on). To set the timer:

Press TIME – use the arrow keys to select the desired pre-set time, 1–10 hours.

Press ON – the timer is activated and the time indicator blinks during the pre-set time

period. Once the heater switches itself on, it remains on for 3 hours, after which it

automatically switches itself off. If you want to switch it off earlier than that, just press

OFF. To extend your sauna time, press ON.

Main power switch.

To be changed more than once: At the bottom of the relay box, the SE unit and the

smaller types of steam generators is a main power switch that disconnects the heater

entirely from the electrical supply. This main switch should only be used if the sauna will

not be used for a longer period, such as several weeks. To be changed more than once:

The memory function must be reset each time the power is interrupted.

INSTRUCTIONS FOR USE

2

1

Functions.

1 = lighting. 2 = on/off. 3 = temperature setting. 4 = time setting. 5 = reduce temperature/time.

6 = increase temperature/time. 7 = display.

Lighting.

Lights automatically when the facility starts and switches off automatically when the

facility shuts down. You can also switch the lighting on or off manually by pressing

LIGHT.

CC 10

C C 1 0

5

4

CC 50

00

6

4

3

Main power switch.

To be changed more than once: At the bottom of the relay box, the SE unit and the

smaller types of steam generators is a main power switch that disconnects the heater

entirely from the electrical supply. This main switch should only be used if the sauna will

not be used for a longer period, such as several weeks. To be changed more than once:

The memory function must be reset each time the power is interrupted.

The thermometer in the sauna/steam bath should be placed at such a height that the

temperature corresponds exactly to the numbers in the panel of the CC 50.

SETTINGS

CC 50, all models

Setting the bathing temperature.

Press TEMP – the previous temperature is displayed. Use the up and down arrows (

) to change the temperature.

Manual on/off.

Press ON to switch the facility on. Press OFF to switch it off. (the LED goes out). If

you forget to switch off the generator manually, it switches off automatically after 3 or 12

hours — depending on the type of control panel.

Timer settings.

(The sauna must be switched off)

Press TIME (the hour digits blink) – set the number of hours until you want to use the

sauna using the up and down arrows (

Press TIME (the minute digits blink) – set the number of minutes until you want to use

the sauna using the up and down arrows (

(Important: The hour or minute digits must be blinking before you press ON).

Press ON – the on time is activated and a red LED blinks until the sauna automatically

starts after the pre-set time. The heater switches off automatically after 3 or 12 hours –

depending on the type of control panel.

You can switch off the sauna manually at any time by pressing OFF.

Changing the type of panel (

1. Connect the voltage.

2. Press

and

at the same time for approx. 6 sek (max. 60 sek. after the

voltage is connected).

3. Change the type of panel according to the scheme with

with TEMP.

Test no.

Test no.

Panel type

*

CC50-3B

50

CC50-12B

51

CC50-3S

53

CC50-12S

54

CC50-1S

15

CC50-1B

18

CC50-24B

58

CC50-0B

59

CC50-24S

68

CC50-0S

69

* Settings at ev. use of extern switch with impulse function.

** Settings at ev. use of extern switch with ON/OFF function.

Code lock to prevent settings from being changed.

First program as «Settings», press on the down arrow ( ), hold it down and press TEMP

and TIME at the same time. The code lock, which prevents changing of settings, is now

activated. To return to unlocked mode, press the down arrow ( ), hold it down and

press OFF at the same time.

Code lock that prevents changing of the temperature setting.

First program as «Settings», press TIME, hold it down and press TEMP and LIGHT at

the same time. The code lock, which prevents changing of the temperature settings, is

now activated. To return to unlocked mode, press the down arrow ( ), hold it down and

press OFF at the same time.

).

).

Factory settings = Test no. 50

and , approve

Description

**

50.A

Sauna 110°C, 3 h running time

51.A

Sauna 110°C, 12 h running time

53.A

Steam 55°C, 3 h running time

54.A

Steam 55°C, 12 h running time

15.A

Steam 55°C, 1 h running time

18.A

Sauna 110°C, 1 h running time

58.A

Sauna 110°C, 24 h running time

59.A

Sauna 110°C, ON/OFF

68.A

Steam 55°C, 24 h running time

69.A

Steam 55°C, ON/OFF

),

5

Scroll To Top

Электронная панель Tylo CC50 предназначена для дистанционного управления сауной, работает совместно с релейной коробкой RB. Устанавливается на стене снаружи сауны, индикация времени и температуры. Подходит для разных электрических печей марки Tylo (серии: SE, SK, SD, SDK и Mega), а также парогенераторов Tylo Steam. Размеры панели: 130x190x27 мм. К печкам SDK/SD необходима релейная коробка RB.