Stanley fatmax fmht77407 инструкция на русском

REV A 12STHT77407

S300

8

1

77407

Stanley Stud Sensor 300

The Stud Sensor 300 uses electronic signals to locate the center of studs, joists

or live AC wires through drywall or other common building materials. Once

the center of a stud has been detected in one pass across the surface, the

Stud Sensor 300 gives a visual display and sounds an audible tone. A marking

channel allows you to easily note the stud center and edges on the wall.

The Stud Sensor 300 will not detect objects in concrete, mortar, block or brick

work, carpeting, foil faced materials, metallic surfaces or ceramic tiles. The

Stud Sensor 300 is not designed to locate non-ferrous or plastic objects such

as pipes.

Note: Read all instructions prior to operating the Stud Sensor 300 and DO NOT

remove any labels from the tool.

WARNING:

Protect Your Eyes, Wear Safety Goggles.

Usage

Detecting Wood / Metal Studs

2

Hold the Stud Sensor 300 fl at

against the surface, making fi rm

contact.

3

Press in and hold the activation

button. A series of tones will sound.

Note: The unit cannot be moved before

calibration is complete.

6

/

7

When it detects the stud

center, the “Center” icon will appear on

the LCD and an audible tone will sound.

Use the marking channel located at the

top of the unit to mark the stud center.

OPERATING INSTRUCTIONS

Battery

1

Open door on back of unit and connect a 9 volt battery

(not included) to clip. Put battery back into case and close

back battery door.

Note: Recommend to replace a new 9 volt battery

when low battery — “Low Battery” will appear on the

LCD.

10

If all segments of the LCD fl ash on and off when

the activation button is pressed, move the Stud Sensor

300 to a different location and try again. Releasing the

activation button will turn off the sensor.

Note: While calibrating, the Stud Sensor 300 must not

be placed directly over a stud, dense material such as

metal, or over a wet or newly painted area, or it will not

properly calibrate.

8

Slide the Stud Sensor 300 slowly across the surface in a straight line.

As it detects a stud, the unit will display the relative position of the stud

on the screen.

• Marking Channel

• Live Wire Warning LED

• LCD Display

• Activation Button

• METAL SCAN Mode

• Stud Location Graphic

• Self-Calibration Complete

• Depth Detection Mode

4

When the unit is calibrated the

“Ready” icon will appear on the LCD.

5

Keep holding the activation button

during all of the following procedures.

Note: Once the Activation button is

released, the unit shuts off.

• STUD or METAL / AC Mode Selection

• Live Wire Detected

• STUD Mode

• Low Battery Indicator

• AC TRACKING Mode

Детектор неоднородностей FatMax S300 FMHT0-77407

Ообенности и преимущества

• Детектор неоднородностей FatMax S300.
• Калибровка с помощью одной кнопки делает ее очень быстрой и простой операцией
• Обнаружение деревянных деталей на глубине до 38 мм
• Обнаружение деталей из черных металлов на глубине до 75 мм
• Обнаружение деталей из цветных металлов на глубине до 38 мм
• Обнаружение проводов с переменным током на глубине до 51 мм
• Определение центра деталей с применением технологии обнаружения за один проход
• Эргономичный корпус из двух материалов для удобства в работе и надежного контроля устройства
• Предупреждающие звуковые сигналы при обнаружении дерева/металла или проводов с переменным током (опция)
• Предупреждающие звуковые сигналы + светодиодная индикация при обнаружении проводов с переменным током
• Инструкция для быстрого начала работы в комплекте