Шевроле траверс инструкция по эксплуатации

Introduction . . . . . . . . . . . . . . . . . . . . . . 2

Keys, Doors, and Windows . . . . . . 7

Seats and Restraints . . . . . . . . . . . 38

Storage . . . . . . . . . . . . . . . . . . . . . . . . . 99

Instruments and Controls . . . . . . 104

Lighting . . . . . . . . . . . . . . . . . . . . . . . 146

Infotainment System . . . . . . . . . . 155

Climate Controls . . . . . . . . . . . . . . 156

Driving and Operating . . . . . . . . . 164

Vehicle Care . . . . . . . . . . . . . . . . . . 246

Service and Maintenance . . . . . 326

Technical Data . . . . . . . . . . . . . . . . 340

Customer Information . . . . . . . . . 343

Reporting Safety Defects . . . . . . 353

OnStar . . . . . . . . . . . . . . . . . . . . . . . . 358

Connected Services . . . . . . . . . . . 366

Index . . . . . . . . . . . . . . . . . . . . 369

Introduction

The names, logos, emblems, slogans, vehicle model names, and vehicle body designs appearing in this manual including, but not limited to, GM, the GM logo, CHEVROLET, the CHEVROLET Emblem, and TRAVERSE are trademarks and/or service marks of General Motors LLC, its subsidiaries, affiliates,

or licensors.

For vehicles first sold in Canada, substitute the name “General Motors of Canada Company” for Chevrolet Motor Division wherever it appears in this manual.

This manual describes features that may or may not be on the vehicle because of optional equipment that

Litho in U.S.A.

Part No. 84337754 A First Printing

© 2019 General Motors LLC. All Rights Reserved.

{Danger

Danger indicates a hazard with a high level of risk which will result in serious injury or death.

{Warning

Warning indicates a hazard that could result in injury or death.

Caution

Caution indicates a hazard that could result in property or vehicle damage.

A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.”

Symbols

The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a specific component, control, message, gauge, or indicator.

M : Shown when the owner’s manual has additional instructions or information.

* : Shown when the service manual has additional instructions or information.

0 : Shown when there is more information on another page — “see page.”

Vehicle Symbol Chart

Here are some additional symbols that may be found on the vehicle and what they mean. See the features in this manual for information.

u : Air Conditioning System

G : Air Conditioning Refrigerant Oil

9 : Airbag Readiness Light

! : Antilock Brake System (ABS) $ : Brake System Warning Light

9: Dispose of Used Components Properly

P: Do Not Apply High Pressure Water

B : Engine Coolant Temperature

_ : Flame/Fire Prohibited

H : Flammable

[: Forward Collision Alert

R: Fuse Block Cover Lock Location

+ : Fuses

j : ISOFIX/LATCH System Child Restraints

1.Air Vents 0 162.

2.Turn Signal Lever. See Turn and Lane-Change Signals 0 150.

IntelliBeam® System Button (If Equipped). See Exterior Lamp Controls 0 146.

3.Instrument Cluster (Uplevel) 0 114 or

Instrument Cluster (Base Level) 0 117.

Driver Information Center (DIC) Display. See Driver Information Center (DIC) 0 133.

4.Windshield Wiper/Washer 0 106.

Rear Window Wiper/Washer 0 107.

5.ENGINE START/STOP Button. See Ignition Positions 0 181.

6.Hazard Warning Flashers 0 150.

7.Light Sensor. See Automatic Headlamp System 0 149.

8.Infotainment 0 155.

Transmission 0 190.

Manual Mode 0 192.

17.Steering Wheel Controls 0 105.

18.Horn 0 106.

Keys, Doors, and

Windows

Keys and Locks

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote Keyless Entry (RKE)

System . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Keyless Entry (RKE)

System Operation . . . . . . . . . . . . . 8

Remote Vehicle Start . . . . . . . . . . 15

Door Locks . . . . . . . . . . . . . . . . . . . . 16

Power Door Locks . . . . . . . . . . . . . 19

Delayed Locking . . . . . . . . . . . . . . . 19

Automatic Door Locks . . . . . . . . . 19

Lockout Protection . . . . . . . . . . . . . 20

Safety Locks . . . . . . . . . . . . . . . . . . . 20

Doors

Liftgate . . . . . . . . . . . . . . . . . . . . . . . . 21

Vehicle Security

Vehicle Security . . . . . . . . . . . . . . . . 28

Vehicle Alarm System . . . . . . . . . 28

Immobilizer . . . . . . . . . . . . . . . . . . . . 29

Immobilizer Operation . . . . . . . . . 29

Exterior Mirrors

Folding Mirrors . . . . . . . . . . . . . . . . . 30

Heated Mirrors . . . . . . . . . . . . . . . . . 31

Automatic Dimming Mirror . . . . . 31

Reverse Tilt Mirrors . . . . . . . . . . . . 31

Interior Mirrors

Interior Rearview Mirrors . . . . . . . 31

Manual Rearview Mirror . . . . . . . . 31

Automatic Dimming Rearview

Mirror . . . . . . . . . . . . . . . . . . . . . . . . . 31

Rear Camera Mirror . . . . . . . . . . . . 32

Windows

Windows . . . . . . . . . . . . . . . . . . . . . . . 33

Power Windows . . . . . . . . . . . . . . . 34

Sun Visors . . . . . . . . . . . . . . . . . . . . . 36

Roof

Sunroof . . . . . . . . . . . . . . . . . . . . . . . . 36

Keys and Locks

Keys

{Warning

Leaving children in a vehicle with a Remote Keyless Entry (RKE) transmitter is dangerous and children or others could be seriously injured or killed. They could operate the power windows or other controls or make the vehicle move. The windows will function with the RKE transmitter in the vehicle, and children or others could be caught in the path of a closing window. Do not leave children in a vehicle with an RKE transmitter.

Remove the key by pressing the button on the side of the RKE transmitter near the bottom and pull the key out. Never pull the key out without pressing the button.

If it becomes difficult to turn the key, inspect the key blade for debris.

See your dealer if a new transmitter is needed.

If locked out of the vehicle, see

Roadside Assistance Program 0 347.

With an active OnStar or connected service plan, an OnStar Advisor may remotely unlock the vehicle. See OnStar Overview 0 358.

Remote Keyless Entry

(RKE) System

See Radio Frequency Statement 0 353.

If there is a decrease in the Remote Keyless Entry (RKE) operating range:

.Check the distance. The transmitter may be too far from the vehicle.

.Check the location. Other vehicles or objects may be blocking the signal.

.Check the transmitter’s battery. See “Battery Replacement” later in this section.

.If the transmitter is still not working correctly, see your dealer or a qualified technician for service.

Remote Keyless Entry

(RKE) System Operation

The Keyless Access system allows for vehicle entry when the Remote Keyless Entry (RKE) transmitter is within 1 m (3 ft). See “Keyless Access Operation” later in this section.

The RKE transmitter may work up to 60 m (197 ft) away from the vehicle.

Other conditions can affect the performance of the transmitter. See

Remote Keyless Entry (RKE) System 0 8.

With Remote Start and Power

Liftgate Shown

Q : Press to lock all doors. The turn signal indicators may flash and/or the horn may sound on the second press to indicate locking. See

Vehicle Personalization 0 137. If the driver door is open when Q is pressed, and Open Door Anti-Lockout is enabled through vehicle personalization, all doors will lock and then the driver door will

immediately unlock. See Vehicle Personalization 0 137. If a passenger door is open when Q is pressed, all doors lock.

Pressing Q may also arm the theft-deterrent system. See Vehicle Alarm System 0 28.

K : Press to unlock the driver door. Press unlock again within

five seconds to unlock all doors. The RKE transmitter can be programmed to unlock all doors on the first button press. See Vehicle Personalization 0 137. The turn signal indicators may flash to indicate unlocking has occurred. See Vehicle Personalization 0 137.

Pressing K may also disarm the theft-deterrent system. See Vehicle Alarm System 0 28.

For vehicles with the manual liftgate, unlocking all doors will also unlock the liftgate.

b : If equipped, press twice quickly to open or close the liftgate. Press again to stop the power liftgate.

7 : Press and release one time to initiate vehicle locator. The exterior lamps flash and the horn chirps

three times. Press and hold 7 for at least three seconds to sound the panic alarm. The horn sounds and the turn signals flash for

30 seconds, or until 7 is pressed again or the vehicle is started.

/ : If equipped, first press and release Q then immediately press

and hold / for at least

four seconds to start the engine from outside the vehicle using the RKE transmitter. See Remote Vehicle Start 0 15.

Keyless Access Operation

The Keyless Access system allows the doors to be locked and unlocked and the liftgate to be accessed

without removing the RKE transmitter from a pocket, purse, briefcase, etc. The RKE transmitter should be within 1 m (3 ft) of the liftgate or door being opened.

Keyless Access can be programmed to unlock all doors on the first lock/unlock press from the driver door. Keyless Unlocking can also be turned off. See Vehicle Personalization 0 137.

If equipped with memory seats, RKE transmitters 1 and 2 are linked to seating positions of memory 1 or 2. See Memory Seats 0 44.

Keyless Unlocking/Locking from the Driver Door

When the doors are locked and the RKE transmitter is within 1 m (3 ft) of the driver door handle, pressing the lock/unlock button on the driver door handle will unlock the driver door.

If the lock/unlock button is pressed again within five seconds, all passenger doors will unlock.

Driver Shown, Passenger Similar

Pressing the lock/unlock button will cause all doors to lock if any of the following occur:

.It has been no more than

five seconds since the first lock/ unlock button press.

.Two lock/unlock button presses were used to unlock all doors.

.Any vehicle door has opened and all doors are now closed.

Keyless Unlocking/Locking from Passenger Doors

When the doors are locked and the RKE transmitter is within 1 m (3 ft) of the door handle, pressing the lock/ unlock button on that door handle will unlock all doors. Pressing the lock/unlock button will cause all doors to lock if any of the following occur:

.The lock/unlock button was used to unlock all doors.

.Any vehicle door has opened and all doors are now closed.

Disable/Enable Keyless Unlocking

of Exterior Door Handles and

Liftgate

If equipped, keyless unlocking of the exterior door handles and liftgate can be disabled and enabled.

Disabling Keyless Unlocking:

With the vehicle off, press and hold Q and K on the RKE transmitter at the same time for approximately three seconds. The turn signal lamps will flash four times quickly to indicate access is disabled. Using

any exterior handle to unlock the doors or open the liftgate will cause the turn signal lamps to flash four times quickly, indicating access is disabled. If disabled, disarm the alarm system before starting the vehicle.

Enabling Keyless Unlocking:

With the vehicle off, press and hold Q and K on the RKE transmitter at the same time for approximately three seconds. The turn signal lamps will flash twice quickly to indicate access is enabled.

Passive Locking

This vehicle will lock several seconds after all doors are closed if the vehicle is off and at least one RKE transmitter has been removed or none remain in the interior.

If other electronic devices interfere with the RKE transmitter signal, the vehicle may not detect the RKE transmitter inside the vehicle.

If passive locking is enabled, the doors may lock with the RKE

transmitter inside the vehicle. Do not leave the RKE transmitter in an unattended vehicle.

To customize the doors to automatically lock when exiting the vehicle, see “Remote Lock, Unlock, Start” under Vehicle Personalization 0 137.

Temporary Disable of Passive

Locking

Temporarily disable passive locking by pressing and holding K on the interior door switch with a door open for at least four seconds, or until three chimes are heard. Passive locking will then remain disabled until Q on the interior door is pressed, or until the vehicle is turned on.

Remote Left in Vehicle Alert

When the vehicle is turned off and an RKE transmitter is left in the vehicle, the horn will chirp three times after all doors are closed. To turn on or off, see Vehicle Personalization 0 137.

Remote No Longer in Vehicle Alert

If the vehicle is on with a door open, and then all doors are closed, the vehicle will check for RKE transmitter(s) inside. If an RKE transmitter is not detected, the Driver Information Center (DIC) will display NO REMOTE DETECTED and the horn will chirp three times. This occurs only once each time the vehicle is driven. See Vehicle Personalization 0 137.

Keyless Liftgate Opening

Press the touch pad on the liftgate handle to open the liftgate if the RKE transmitter is within 1 m (3 ft).

Key Access

To access a vehicle with a weak transmitter battery, see Door Locks

0 16.

Programming Transmitters to the Vehicle

Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and

programmed through your dealer. The vehicle can be reprogrammed so that lost or stolen transmitters no longer work. Each vehicle can have up to eight transmitters matched

to it.

Programming with Recognized Transmitters

A new transmitter can be programmed to the vehicle when there are two recognized transmitters.

To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you.

1.Remove the key by pressing the button on the side of the RKE transmitter near the bottom and pull the key out. Never pull the key out without pressing the button.

2.Remove the key lock cylinder cap on the driver door handle. See Door Locks 0 16. Place the two recognized transmitters in the transmitter pocket.

3.Insert the vehicle key of the transmitter into the key lock cylinder on the driver door handle and turn the key, counterclockwise, to the unlock position five times within

10 seconds.

The DIC displays READY FOR REMOTE #3, 4, 5, ETC.

4.Place the new transmitter into the transmitter pocket. The transmitter pocket is inside the center console storage area between the driver and front passenger seats, underneath the liner.

5.Press ENGINE START/STOP. When the transmitter is learned the DIC display will show that it is ready to program the next transmitter.

6.Remove the transmitter from the transmitter pocket and press the transmitter K or Q button.

To program additional transmitters, repeat Steps 3–5.

When all additional transmitters are programmed, press and hold ENGINE START/STOP for 12 seconds to exit programming mode.

7.Put the key back into the transmitter.

8.Replace the key lock cylinder cap. See Door Locks 0 16.

Programming without Recognized Transmitters

If two currently recognized transmitters are not available, follow this procedure to program up to eight transmitters. This feature is not available in Canada. This

procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you.

1.Remove the key by pressing the button on the side of the RKE transmitter near the bottom and pull the key out. Never pull the key out without pressing the button.

2.Remove the key lock cylinder cap on the driver door handle. See Door Locks 0 16. Insert the vehicle key of the transmitter into the key lock cylinder on the driver door handle and turn the key, counterclockwise, to the unlock position five times within

10 seconds.

The DIC displays REMOTE LEARN PENDING, PLEASE WAIT.

3.Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN and then press ENGINE START/STOP.

The DIC will again display REMOTE LEARN PENDING, PLEASE WAIT.

4.Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. Remaining transmitters can be relearned during the next steps.

The DIC display should now show READY FOR REMOTE

# 1.

5.Place the new transmitter into the transmitter pocket. The transmitter pocket is inside the center console storage area between the driver and front passenger seats, underneath the liner.

6.Press ENGINE START/STOP. When the transmitter is learned the DIC display will show that it is ready to program the next transmitter.

7.Remove the transmitter from the transmitter pocket and press the transmitter K or Q button.

To program additional transmitters, repeat Steps 4–6.

When all additional transmitters are programmed, press and hold ENGINE START/STOP for 12 seconds to exit programming mode.

8.Put the key back into the transmitter.

9.Replace the key lock cylinder cap. See Door Locks 0 16.

Starting the Vehicle with a Low Transmitter Battery

When the vehicle is started, if the transmitter battery is weak, the DIC may display NO REMOTE DETECTED or NO REMOTE KEY WAS DETECTED PLACE KEY IN TRANSMITTER POCKET THEN START YOUR VEHICLE. The DIC may also display REPLACE BATTERY IN REMOTE KEY.

To start the vehicle:

1.Open the center console storage area by opening the armrest.

2.Place the transmitter in the transmitter pocket.

3.With the vehicle in P (Park) or N (Neutral), press the brake pedal and ENGINE START/STOP.

Replace the transmitter battery as soon as possible.

Battery Replacement

Replace the battery if the DIC displays REPLACE BATTERY IN REMOTE KEY.

Caution

When replacing the battery, do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter.

The battery is not rechargeable. To replace the battery:

1.Press the button on the side of the RKE transmitter and pull the key out. Never pull the key out without pressing the button.

2.Separate the two halves of the transmitter using a flat tool inserted into the area near the key slot.

3.Remove the battery by pushing on the battery and sliding it toward the bottom of the transmitter.

4.Insert the new battery, positive side facing the back cover. Push the battery down until it is held in place. Replace with a CR2032 or equivalent battery.

5.Snap the battery cover back on to the transmitter.

6. Reinsert the key.

Remote Vehicle Start

If equipped, this feature allows the engine to be started from outside of the vehicle.

/ : This button will be on the RKE transmitter if the vehicle has remote start.

The climate control system will use the previous settings during a remote start. The rear defog may come on during a remote start based on cold ambient conditions. The rear fog indicator light does not come on during a remote start.

If the vehicle has auto heated or ventilated seats, they may come on during a remote start. See Heated and Ventilated Front Seats 0 47.

If equipped with a remote start heated steering wheel, it may come on during a remote start when it is cold outside, if enabled. See Heated Steering Wheel 0 105 and

Vehicle Personalization 0 137.

Laws in some local communities may restrict the use of remote starters. For example, some laws may require a person using remote start to have the vehicle in view. Check local regulations for any requirements.

Do not use the remote start feature if the vehicle is low on fuel. The vehicle could run out of fuel.

Other conditions can affect the performance of the transmitter. See

Remote Keyless Entry (RKE) System 0 8.

Starting the Engine Using Remote

Start

1.Press and release Q on the RKE transmitter.

2.Immediately press and hold / for at least four seconds or until the turn signal lamps flash. The turn signal lamps flashing confirms the request to remote start the vehicle has been received.

During the remote start the doors will be locked and the parking lamps will remain on as long as the engine is running.

The engine will shut off after 15 minutes unless a time extension is done or the vehicle is started.

3.With the RKE transmitter in the vehicle, press the brake pedal and start the vehicle to drive.

Extending Engine Run Time

The engine run time can also be extended by another 15 minutes, if during the first 15 minutes Steps 1 and 2 are repeated while the engine is still running. An extension can be requested

30 seconds after starting. This provides a total of 30 minutes.

The remote start can only be extended once.

When the remote start is extended, the second 15-minute period is added on to the first 15 minutes for a total of 30 minutes.

A maximum of two remote starts, or a remote start with an extension, are allowed between ignition cycles.

The ignition must be turned on and then off before the remote start procedure can be used again.

Canceling a Remote Start

To cancel a remote start, do any of the following:

.Press and hold / until the parking lamps turn off.

.Turn on the hazard warning flashers.

.Turn the vehicle on and then off.

Conditions in Which Remote Start

Will Not Work

The remote start will not operate if any of the following occur:

.An RKE transmitter is in the vehicle.

.The hood is not closed.

.The ignition is in any mode other than off.

.The hazard warning flashers are on.

.There is an emission control system malfunction.

.The engine coolant temperature is too high.

.The oil pressure is low.

.Two remote vehicle starts or a start with an extension have already been used.

.The vehicle is not in P (Park).

Door Locks

{Warning

Unlocked doors can be dangerous.

.Passengers, especially children, can easily open the doors and fall out of a moving vehicle. The doors can be unlocked and opened while the vehicle is moving. The chance of

(Continued)

Warning (Continued)

being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear seat belts properly and the doors should be locked whenever the vehicle is driven.

.Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever leaving it.

.Outsiders can easily enter through an unlocked door when you slow down or stop the vehicle. Locking the doors can help prevent this from happening.

To lock or unlock the doors from the outside:

.Press Q or K on the Remote Keyless Entry (RKE) transmitter. See Remote Keyless Entry (RKE) System Operation 0 8.

.Use the key in the driver door. The key lock cylinder is covered with a cap.

To lock or unlock the doors from the inside:

.Press Q or K on the power door lock switch.

.Push down on a door lock knob to lock a door.

.Pull the door handle once to unlock the door. Pull the handle again to unlatch it.

Keyless Access

If equipped, the RKE transmitter must be within 1 m (3 ft) of the liftgate or door being opened. Press the button on the door handle to open. See “Keyless Access Operation” in Remote Keyless Entry (RKE) System Operation 0 8.

Driver Door Key Lock Cylinder

Access (In Case of Dead

Battery)

To access the driver door key lock cylinder:

1.Pull the door handle (1) to the open position and hold it open until cap removal is complete.

2.Insert the key into the slot (3) on the bottom of the cap (2) and lift the key upward.

3.Move the cap (2) rearward and remove.

4.Use the key in the cylinder.

To replace the cap:

1.Pull the door handle (1) to the open position and hold it open until cap installation is complete.

2.Insert the two tabs (6) at the back of the cap between the seal (5) and the metal base (4).

3.Slide the cap forward and press the forward edge to install the cap in place.

4.Release the door handle.

5. Check that the cap is secure.

Free-Turning Locks

The door key lock cylinder turns freely when either the wrong key is used, or the correct key is not fully inserted. The free-turning door lock feature prevents the lock from being forced open. To reset the lock, turn it to the vertical position with the correct key fully inserted. Remove the key and insert it again. If this does not reset the lock, turn the key halfway around in the cylinder and repeat the reset procedure.

Power Door Locks

Q : Press to lock the doors.

K : Press to unlock the doors.

Delayed Locking

This feature delays the locking of the doors until five seconds after all doors are closed.

Delayed locking can only be turned on when the Open Door Anti-Lockout feature has been turned off.

When Q is pressed on the power door lock switch while the door is open, a chime will sound three times indicating delayed locking is active.

The doors will lock automatically five seconds after all doors are closed. If a door is reopened before that time, the five-second timer will reset when all doors are closed again.

Press Q on the door lock switch

again or press Q on the RKE transmitter to lock the doors immediately.

This feature can also be programmed. See Vehicle Personalization 0 137.

Automatic Door Locks

The doors will lock automatically when all doors are closed, the ignition is on, and the vehicle is shifted out of P (Park).

If a vehicle door is unlocked and then opened and closed, the doors will lock either when your foot is

removed from the brake or the vehicle speed becomes faster than 13 km/h (8 mph).

To unlock the doors:

.Press K on a door.

.Shift the transmission into P (Park).

Automatic door locking cannot be disabled. Automatic door unlocking can be programmed. See Vehicle Personalization 0 137.

Lockout Protection

If the vehicle is started or in ACC/ ACCESSORY and the power door lock switch is pressed with the driver door open, all the doors will lock and only the driver door will unlock.

If the vehicle is off and locking is requested while a door is open, when all doors are closed the vehicle will check for RKE transmitters inside. If an RKE transmitter is detected and the number of RKE transmitters inside

has not reduced, the driver door will unlock and the horn will chirp three times.

Lockout Protection can be manually overridden with the driver door open

by pressing and holding Q on the power door lock switch.

Open Door Anti-Lockout

If Open Door Anti-Lockout is turned on and the vehicle is off, the driver door is open, and locking is requested, all the doors will lock and the driver door will unlock. The Open Door Anti-Lockout feature can be turned on or off. See Vehicle Personalization 0 137.

Safety Locks

The rear door safety locks prevent passengers from opening the rear doors from inside the vehicle.

Manual Safety Locks

If equipped, the safety lock is on the inside edge of the rear doors. To use the safety lock:

1.Move the lever down to the lock position.

2.Close the door.

3.Do the same for the other rear door.

To open a rear door when the safety lock is on:

1.Unlock the door by activating the inside handle, by pressing the power door lock switch,

or by using the Remote Keyless Entry (RKE) transmitter.

2.Open the door from the outside.

When the safety lock is enabled, adults and older children will not be able to open the rear door from the inside. Cancel the safety locks to enable the doors to open from the inside.

To cancel the safety lock:

1.Unlock the door and open it from the outside.

2.Move the lever up to unlock. Do the same for the other door.

Doors

Liftgate

{Warning

Exhaust gases can enter the vehicle if it is driven with the liftgate or trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or

liftgate. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.

If the vehicle must be driven with the liftgate or trunk/hatch open:

.Close all of the windows.

.Fully open the air outlets on or under the instrument panel.

Warning (Continued)

.Adjust the climate control system to a setting that brings in only outside air and set the fan speed to the highest setting. See “Climate Control Systems” in the Index.

.If the vehicle is equipped with a power liftgate, disable the power liftgate function.

See Engine Exhaust 0 189.

Caution

To avoid damage to the liftgate or liftgate glass, make sure the area above and behind the liftgate is clear before opening it.

Manual Liftgate

(RKE) transmitter twice within

five seconds. See Remote Keyless Entry (RKE) System Operation 0 8.

To open the liftgate, press the touch pad in the liftgate handle and lift up.

If equipped with Keyless Access, the liftgate can be opened when locked if the RKE transmitter is within 1 m (3 ft) of the liftgate. See

Remote Keyless Entry (RKE) System Operation 0 8.

Use the pull cup to lower and close the liftgate. Do not press the touch pad while closing the liftgate. This will cause the liftgate to be unlatched.

The liftgate has an electric latch.

If the battery is disconnected or has low voltage, the liftgate will not open. The liftgate will resume operation when the battery is reconnected and charged.

Always close the liftgate before driving.

Power Liftgate Operation

{Warning

You or others could be injured if caught in the path of the power liftgate. Make sure there is no one in the way of the liftgate as it is opening and closing.

Caution

Driving with an open and unsecured liftgate may result in damage to the power liftgate components.

If equipped with a power liftgate, the power liftgate switch is on the driver door. The vehicle must be in

P (Park).

The modes are:

.MAX: Opens to maximum height.

.3/4: Opens to a reduced height that can be set from 3/4 to fully open. Use to prevent the liftgate from opening into overhead obstructions such as a garage door or roof-mounted cargo. The liftgate can be manually opened all the way.

.OFF: Opens manually only.

To power open or close the liftgate, select MAX or 3/4 mode.

.Press b twice quickly on the RKE transmitter until the liftgate moves.

.Press 8on the driver door. The driver door must be unlocked.

.Press the touch pad in the liftgate handle after unlocking all doors. A locked vehicle can be opened if the RKE transmitter is within 1 m (3 ft) of the liftgate.

.Press l on the bottom of the liftgate to close.

Press any liftgate button, the touch pad, or b on the RKE transmitter while the liftgate is moving to stop it. Pressing any liftgate button or pressing b twice quickly on the RKE transmitter restarts the operation in the reverse direction. Pressing the touch pad on the liftgate handle will restart the motion, but only in the opening direction

Caution

Manually forcing the liftgate to open or close during a power cycle can damage the vehicle. Allow the power cycle to complete.

The power liftgate may be temporarily disabled under extreme low temperatures, or after repeated power cycling over a short period of time. If this occurs, the liftgate can still be operated manually.

If the vehicle is shifted out of

P (Park) while the power function is in progress, the liftgate will continue to completion. If the vehicle is accelerated before the liftgate has completed moving, the liftgate may stop or reverse direction. Check for DIC messages and make sure the liftgate is closed and latched before driving.

Falling Liftgate Detection

If the power liftgate automatically closes after a power opening cycle, it indicates that the system is reacting to excess weight on the liftgate or a possible support strut failure. A repetitive chime will sound while the falling liftgate detection feature is operating. Remove any excess weight. If the liftgate continues to automatically close after opening, see your dealer for service before using the power liftgate.

Interfering with the power liftgate motion or manually closing the liftgate too quickly after power opening may resemble a support strut failure. This could also activate

the falling liftgate detection feature. Allow the liftgate to complete its operation and wait a few seconds before manually closing the liftgate.

Obstacle Detection Features

If the liftgate encounters an obstacle during a power open or close cycle, the liftgate will automatically reverse direction and move a short distance away from the obstacle. After removing the obstruction, the power liftgate operation can be used again. If the liftgate encounters multiple obstacles on the same power cycle, the power function will deactivate. After removing the obstructions, manually close the liftgate which will allow normal power operation functions to resume.

If the vehicle is locked while the liftgate is closing, and an obstacle is encountered that prevents the liftgate from completely closing, the horn will sound as an alert that the liftgate did not close.

Pinch sensors are on the side edges of the liftgate. If an object is caught between the liftgate and the

vehicle and presses against a sensor, the liftgate will reverse direction and open fully. The liftgate will remain open until it is activated again or closed manually.

Setting the 3/4 Mode

To change the position the liftgate stops at when opening:

1.Select MAX or 3/4 mode and power open the liftgate.

2.Stop the liftgate movement at the desired height by pressing any liftgate button. Manually adjust the liftgate position if needed.

3.Press and hold lat the bottom of the liftgate until the turn signals flash and a beep sounds. This indicates the setting has been recorded.

The liftgate cannot be set below a minimum programmable height. If there is no light flash or sound,

then the height adjustment may be too low.

Manual Operation

Select OFF to manually operate the liftgate. See “Manual Liftgate” at the beginning of this section.

Caution

Attempting to move the liftgate too quickly and with excessive force may result in damage to the vehicle.

Operate the liftgate manually with a smooth motion and moderate speed. The system includes a feature which limits the manual closing speed to protect the components.

Hands-Free Operation

If equipped, the liftgate may be operated with a kicking motion under the left side of the rear bumper at the location of the projected logo. The RKE transmitter must be within 1 m (3 ft) of the rear bumper to operate the power liftgate hands-free.

The hands-free feature will not work while the liftgate is moving. To stop the liftgate while in motion use one of the liftgate switches.

The hands-free feature can be customized. See Vehicle Personalization 0 137. Choose from the following:

On-Open and Close : The kicking motion is activated to both open and close the liftgate.

On-Open Only : The kicking motion is activated to only open the liftgate.

Off : The feature is disabled.

Kick Zone

To operate, move your foot in a forward kicking motion under the left side of the rear bumper at the location of the projected logo, then pull it back. The kick must come within 14 cm (6 in) of the rear bumper to activate.

Caution

Splashing water may cause the liftgate to open. Keep the RKE transmitter away from the rear bumper detection area or turn the

(Continued)

Caution (Continued)

liftgate mode to OFF when cleaning or working near the rear bumper to avoid accidental opening.

.Do not sweep your foot side to side.

.Do not keep your foot under the bumper; the liftgate will not activate.

.Do not touch the liftgate until it has stopped moving.

This feature may be temporarily disabled under some conditions. If the liftgate does not respond to the kick, open or close the liftgate by another method or start the vehicle. The feature will be re-enabled.

When closing the liftgate using this feature, there will be a short delay. The taillamps will flash and a chime will sound.

Step away from the liftgate before it starts moving.

Projected Logo

If equipped with this feature, a vehicle logo will be projected for one minute onto the ground near the rear bumper when an RKE transmitter is detected within approximately 2 m (6 ft). The projected logo may not be visible under brighter daytime conditions.

1.1 m (3 ft) Hands-Free Operation Detection Zone

2.2 m (6 ft) Projected Logo Detection Zone

The projected logo shows where the kicking motion is to take place.

The projected logo will only be available for this RKE transmitter after it has been out of range for at least 20 seconds.

If an RKE transmitter is again detected within approximately 2 m (6 ft) of the liftgate, or another hands-free operation has been detected, the one-minute timer will be reset.

The projected logo will not work under these conditions:

.The vehicle battery is low.

.The transmission is not in P (Park).

.Hands Free Liftgate Control is set to off in vehicle personalization. See Vehicle Personalization 0 137.

.Power liftgate is turned off.

.The vehicle remains parked for 72 hours or more, with no RKE transmitter use or Keyless Access operation. To re-enable, press any button on the RKE transmitter or open and close a vehicle door.

The projected logo will not work for a single RKE transmitter when a transmitter:

.Has been left within approximately 5 m (15 ft) of the liftgate for several minutes.

.Has been left inside the vehicle and all vehicle doors are closed.

.Has approached the area outside of the liftgate five times within 10 minutes.

Lens Cleaning

Clean the recessed lens with a soft, dampened cloth.

Vehicle Security

This vehicle has theft-deterrent features; however, they do not make the vehicle impossible to steal.

Vehicle Alarm System

This vehicle has an anti-theft alarm system.

The indicator light, on the instrument panel near the windshield, indicates the status of the system.

Off : Alarm system is disarmed.

On Solid : Vehicle is secured during the delay to arm the system.

Fast Flash : Vehicle is unsecured. A door, the hood, or the liftgate

is open.

Slow Flash : Alarm system is armed.

Arming the Alarm System

1.Close the liftgate and the hood. Turn off the vehicle.

2.Lock the vehicle in one of three ways:

. Use the RKE transmitter.

. Use the Keyless Access system.

.With a door open, press the inside Q.

3.After 30 seconds the alarm system will arm, and the indicator light will begin to slowly flash indicating the alarm system is operating. Pressing Q on the RKE transmitter a second time will

bypass the 30-second delay and immediately arm the alarm system.

The vehicle alarm system will not arm if the doors are locked with the key.

If the driver door is opened without first unlocking with the RKE transmitter, the horn will chirp and the lights will flash to indicate pre-alarm. If the vehicle is not started, or the door is not unlocked

by pressing K on the RKE transmitter during the 10-second pre-alarm, the alarm will be activated.

The alarm will also be activated if a passenger door, the liftgate, or the hood is opened without first disarming the system. When the alarm is activated, the turn signals flash and the horn sounds for about 30 seconds. The alarm system will then re-arm to monitor for the next unauthorized event.

Disarming the Alarm System

To disarm the alarm system or turn off the alarm if it has been activated:

.Press K on the RKE transmitter.

.Unlock the vehicle using the Keyless Access system.

.Start the vehicle.

To avoid setting off the alarm by accident:

.Lock the vehicle after all occupants have left the vehicle and all doors are closed.

.Always unlock a door with the RKE transmitter or use the Keyless Access system.

Unlocking the driver door with the key will not disarm the system or turn off the alarm.

How to Detect a Tamper Condition

If K is pressed and the horn chirps and the lights flash three times, the alarm was activated while the alarm system was armed.

If the alarm system has been activated, a message will appear on the Driver Information Center (DIC).

Immobilizer

See Radio Frequency Statement 0 353.

Immobilizer Operation

This vehicle has a passive theft-deterrent system.

The system does not have to be manually armed or disarmed.

The vehicle is automatically immobilized when the transmitter leaves the vehicle.

The immobilization system is disarmed when the ignition is turned on or in ACC/ACCESSORY and a valid Remote Keyless Entry (RKE) transmitter is in the vehicle.

The security light, in the instrument cluster, comes on if there is a problem with arming or disarming the theft-deterrent system.

The system has one or more RKE transmitters matched to an immobilizer control unit in your vehicle. Only a correctly matched RKE transmitter will start the vehicle. If the transmitter is ever damaged, you may not be able to start your vehicle.

When trying to start the vehicle, the security light may come on briefly when the ignition is turned on.

If the engine does not start and the security light stays on, there is a problem with the system. Turn the ignition off and try again.

If the vehicle will not change ignition modes (ACC/ACCESSORY, on, off), and the RKE transmitter appears to

be undamaged, try another transmitter. Or, you may try placing the transmitter in the transmitter pocket in the center console. See

Remote Keyless Entry (RKE) System Operation 0 8.

If the ignition mode will not change with the other transmitter, or with the transmitter in the transmitter pocket, your vehicle needs service. If the ignition does change modes, the first transmitter may be faulty. See your dealer who can service the theft-deterrent system and have a new RKE transmitter programmed to the vehicle.

It is possible for the immobilizer system to learn new or replacement RKE transmitters. Up to eight transmitters can be programmed to the vehicle. To program additional transmitters, see “Programming Transmitters to the Vehicle” under

Remote Keyless Entry (RKE) System Operation 0 8.

Exterior Mirrors

Convex Mirrors

{Warning

A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.

The passenger side mirror is convex shaped. A convex mirror’s surface is curved so more can be seen from the driver seat.

Power Mirrors

To adjust the mirrors:

1.Press jor | to choose the driver or passenger mirror.

2.Press the arrows on the control pad to move each mirror in the desired direction.

Folding Mirrors

Manual Folding Mirrors

automatic car wash. Push the mirror outward to return it to the original position.

Memory Mirrors

The vehicle may have memory mirrors. See Memory Seats 0 44.

Lane Change Alert (LCA)

The vehicle may have LCA. See

Lane Change Alert (LCA) 0 224.

Side Blind Zone Alert

The vehicle may have Side Blind Zone Alert. See Side Blind Zone Alert (SBZA) 0 224.

Heated Mirrors

If equipped, the heated outside mirrors turn on when the rear window defogger is on and help to clear fog or frost from the surface of the mirrors.

K : This button is on the climate control panel.

See “Rear Window Defogger” under

Dual Automatic Climate Control System 0 156.

Automatic Dimming

Mirror

The vehicle has an automatic dimming outside mirror on the driver side. The mirror will adjust for the glare of headlamps behind you.

Reverse Tilt Mirrors

If equipped with memory seats, the passenger and/or driver mirror tilts to a preselected position when the vehicle is in R (Reverse). This allows the curb to be seen when parallel parking.

The mirror(s) return to the original position when:

.The vehicle is shifted out of R (Reverse), or remains in R (Reverse) for about

30 seconds.

.The ignition is turned off.

.The vehicle is driven in

R (Reverse) above a set speed.

To turn this feature on or off, see

Vehicle Personalization 0 137.

Interior Mirrors

Interior Rearview Mirrors

Adjust the rearview mirror for a clear view of the area behind your vehicle.

Do not spray glass cleaner directly on the mirror. Use a soft towel dampened with water.

Manual Rearview Mirror

If equipped, push the tab forward for daytime use and pull it rearward for nighttime use to avoid glare of the headlamps from behind.

Automatic Dimming

Rearview Mirror

If equipped, automatic dimming reduces the glare of headlamps from behind. The dimming feature comes on when the vehicle is started.

Rear Camera Mirror

If equipped, this automatic dimming mirror provides a wide angle camera view of the area behind the vehicle.

Pull the tab rearward to turn on the display. Push the tab forward to turn it off. When off, the mirror is automatic dimming. Adjust the mirror for a clear view of the area behind the vehicle while the display is off.

To adjust the brightness, press the button (1) on the back of the rearview mirror without covering the light sensor (2).

Each button press cycles the brightness between five settings.

{Warning

The Rear Camera Mirror (RCM) has a limited view. Portions of the road, vehicles, and other objects may not be seen. Do not drive or park the vehicle using only this camera. Objects may appear closer than they are. Check the outside mirrors or glance over your shoulder when making lane changes or merging. Failure to use proper care may result in injury, death, or vehicle damage.

The camera that provides the Rear Camera Mirror (RCM) image is above the license plate, next to the Rear Vision Camera (RVC).

Troubleshooting

If the tab is in the rearward position and a blue screen and d are displayed in the mirror and the display shuts off, see your dealer for service.

The RCM may not work properly or display a clear image if:

.There is glare from the sun or headlamps. This may obstruct objects from view.

.Dirt, snow, or other debris blocks the camera lens. Clean the lens with a soft damp cloth.

.The back of the vehicle has been damaged and the position and mounting angle of the camera has changed.

Windows

{Warning

Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke.

The vehicle aerodynamics are designed to improve fuel economy performance. This may result in a pulsing sound when either rear window is down and the front windows are up. To reduce the sound, open either a front window or the sunroof, if equipped.

Power Windows

{Warning

Leaving children in a vehicle with a Remote Keyless Entry (RKE) transmitter is dangerous and children or others could be seriously injured or killed. They could operate the power windows or other controls or make the vehicle move. The windows will function with the RKE transmitter in the vehicle, and children or others could be caught in the path of a closing window. Do not leave children in a vehicle with an RKE transmitter.

The power windows work when the ignition is on, in ACC/ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) 0 186.

Using the window switch, press to open or pull to close the window.

The windows may be temporarily disabled if they are used repeatedly within a short time.

Window Lockout

This feature stops the rear passenger window switches from working:

.Press 2 to engage the rear window lockout feature. The indicator light is on when engaged.

.Press 2 again to disengage.

Window Express Movement

All windows can be opened without holding the window switch. Press the switch down fully and quickly release to express open the window.

If equipped, pull the window switch up fully and quickly release to express close the window.

Briefly press or pull the window switch in the same direction to stop that window’s express movement.

Window Automatic Reversal

System

The express-close feature will reverse window movement if it comes in contact with an object. Extreme cold or ice could cause the window to auto-reverse. The window will operate normally after the object or condition is removed.

Automatic Reversal System

Override

{Warning

If automatic reversal system override is active, the window will not reverse automatically. You or others could be injured and the window could be damaged. Before using automatic reversal system override, make sure that all people and obstructions are clear of the window path.

When the engine is on, override the automatic reversal system by pulling and holding the window switch if conditions prevent it from closing.

Programming the Power

Windows

Programming may be necessary if the vehicle battery has been disconnected or discharged. If the window is unable to express-up, program each express-close window:

1.Close all doors.

2.Turn the ignition on or to ACC/ ACCESSORY.

3.Partially open the window to be programmed. Then close it and continue to pull the switch briefly after the window has fully closed.

4.Open the window and continue to press the switch briefly after the window has fully opened.

Remote Window Operation

If equipped, this feature allows all the windows to be opened remotely. If enabled in vehicle personalization,

press and hold K on the RKE transmitter. See Vehicle Personalization 0 137.

Sun Visors

Pull the sun visor down to block glare. Detach the sun visor from the center mount to pivot to the side window and, if equipped, extend along the rod.

Roof

Sunroof

If equipped, the ignition must be on or in ACC/ACCESSORY,

or Retained Accessory Power (RAP) must be active to operate the sunroof. See Ignition Positions

0 181 and

Retained Accessory Power (RAP) 0 186.

1.Sunroof Switch (SLIDE)

2.Vent Switch (TILT)

Slide Switch

Express-Open/Express-Close :

Press and release D (1) to express-open the sunroof. The sunshade will not open automatically. Press and release g(1) to express-close the sunroof.

Open/Close (Manual Mode) : Fully press D (1) to open the sunroof. The sunshade will not automatically open with the sunroof. Release to stop at the desired position. Fully press g(1) to close the sunroof. Release to stop at the desired position.

Tilt Switch

Vent Feature : Press E (2) to vent the sunroof. Press again and hold to open the sunroof. Release to stop at the desired position. The sunshade will not open automatically. Press

g(2) to express-close the sunroof. Press again to stop the movement.

The front sunshade can only be opened and closed manually. The sunshade can be opened by pushing up on the handle, and closed by pulling forward on the handle until it latches. Do not try to close the sunshade while the sunroof is fully opened or in the vent position.

If equipped, the rear sunshade can only be opened or closed manually. To open, press the latch button (if equipped) on the handle while pushing up to unlatch it. The sunshade will retract to the open position. To close the sunshade, pull the handle forward until it latches.

The sunroof cannot be opened or closed if the vehicle has an electrical failure.

Automatic Reversal System

The sunroof has an automatic reversal system that is only active when the sunroof is operated in express-close mode.

If an object is in the path while express closing, the reversal system will detect an object, stop, and open the sunroof again.

If frost or other conditions prevent closing, override the feature by closing the sunroof in manual mode. To stop movement, release the switch.

Dirt and debris may collect on the sunroof seal or in the track. This could cause an issue with sunroof operation or noise. It could also plug the water drainage system.

Periodically open the sunroof and remove any obstacles or loose debris. Wipe the sunroof seal and roof sealing area using a clean cloth, mild soap, and water. Do not remove grease from the sunroof.

If water is seen dripping into the water drainage system, this is normal.

Seats and

Restraints

Head Restraints

Head Restraints . . . . . . . . . . . . . . . 39

Front Seats

Seat Adjustment . . . . . . . . . . . . . . . 41

Power Seat Adjustment . . . . . . . . 41

Lumbar Adjustment . . . . . . . . . . . . 42

Reclining Seatbacks . . . . . . . . . . . 42

Memory Seats . . . . . . . . . . . . . . . . . 44

Heated and Ventilated Front

Seats . . . . . . . . . . . . . . . . . . . . . . . . . 47

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . . 48

Heated Rear Seats . . . . . . . . . . . . 51

Third Row Seats . . . . . . . . . . . . . . . 52

Seat Belts

Seat Belts . . . . . . . . . . . . . . . . . . . . . 54 How to Wear Seat Belts

Properly . . . . . . . . . . . . . . . . . . . . . . 56 Lap-Shoulder Belt . . . . . . . . . . . . . 58 Seat Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . . . 61 Seat Belt Extender . . . . . . . . . . . . . 62 Safety System Check . . . . . . . . . . 62

Seat Belt Care . . . . . . . . . . . . . . . . . 62

Replacing Seat Belt System

Parts after a Crash . . . . . . . . . . . 63

Airbag System

Airbag System . . . . . . . . . . . . . . . . . 64 Where Are the Airbags? . . . . . . . 66 When Should an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . . . 67 What Makes an Airbag

Inflate? . . . . . . . . . . . . . . . . . . . . . . . 68 How Does an Airbag

Restrain? . . . . . . . . . . . . . . . . . . . . . 68 What Will You See after an

Airbag Inflates? . . . . . . . . . . . . . . 69 Passenger Sensing System . . . 70 Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . . . 74 Adding Equipment to the

Airbag-Equipped Vehicle . . . . . 75 Airbag System Check . . . . . . . . . . 76 Replacing Airbag System Parts

after a Crash . . . . . . . . . . . . . . . . . 76

Child Restraints

Older Children . . . . . . . . . . . . . . . . . 76 Infants and Young Children . . . . 78 Child Restraint Systems . . . . . . . 80 Where to Put the Restraint . . . . . 82 Lower Anchors and Tethers for

Children (LATCH System) . . . . 83

Replacing LATCH System Parts

After a Crash . . . . . . . . . . . . . . . . . 93

Securing Child Restraints (With

the Seat Belt in the

Rear Seat) . . . . . . . . . . . . . . . . . . . 93

Securing Child Restraints (With

the Seat Belt in the

Front Seat) . . . . . . . . . . . . . . . . . . . 95

Head Restraints

Front Seats

{Warning

With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/ spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly.

The vehicle’s front seats have adjustable head restraints in the outboard seating positions.

Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash.

The height of the head restraint can be adjusted.

To raise or lower the head restraint, press the button located on the side of the head restraint, and pull up or push the head restraint down, and release the button. Pull and push on the head restraint after the button is released to make sure that it is locked in place.

The front seat outboard head restraints are not removable.

Rear Seats

Second Row Seats

The vehicle’s second row seats have adjustable head restraints in the outboard seating positions.

The height of the head restraint can be adjusted. Pull the head restraint up to raise it. Try to move the head restraint to make sure that it is locked in place.

To lower the head restraint, press the button, located on the top of the seatback, and push the head restraint down. Try to move the head restraint after the button is released to make sure that it is locked in place.

Always adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head.

If you are installing a child restraint in the rear seat, see “Securing a Child Restraint Designed for the LATCH System” under Lower Anchors and Tethers for Children (LATCH System) 0 83.

Third Row Seats

The vehicle’s third row seats have head restraints in the outboard seating positions that cannot be adjusted up or down.

The third row outboard head restraints are not removable.

The third row outboard head restraints are designed to be folded.

The head restraint can be folded to allow for better visibility when the rear seat is unoccupied.

When folding the seatback down, the head restraint will automatically fold out of the way as the seat is folded down.

Return the lowered head restraint to the upright position until it locks into place. Push and pull on the head restraint to make sure it is locked.

Front Seats

Seat Adjustment

{Warning

You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. Adjust the driver seat only when the vehicle is not moving.

To adjust a manual seat:

1.Lift the handle under the seat to unlock it.

2.Move the seat forward or rearward to adjust the seat position.

3.Release the handle to stop the seat from moving.

4.Try to move the seat back and forth to be sure it is locked in place.

Seat Height Adjuster

If equipped, move the lever up or down to manually raise or lower the seat.

Power Seat Adjustment

{Warning

You can lose control of the vehicle if you try to adjust a driver seat while the vehicle is moving. Adjust the driver seat only when the vehicle is not moving.

{Warning

The power seats will work with the ignition off. Children could operate the power seats and be injured. Never leave children alone in the vehicle.

To adjust the seat:

.Move the seat forward or rearward by sliding the control forward or rearward.

.Raise or lower the front part of the seat cushion by moving the front of the control up or down.

.Raise or lower the entire seat by moving the rear of the control up or down.

To adjust the seatback, see

Reclining Seatbacks 0 42.

To adjust the lumbar support, see

Lumbar Adjustment 0 42.

Lumbar Adjustment

Press and hold the control forward to increase or rearward to decrease support.

Reclining Seatbacks

{Warning

Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the seat belts cannot do

their job.

(Continued)

Warning (Continued)

The shoulder belt will not be against your body. Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries.

The lap belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries.

For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the seat belt properly.

Do not have a seatback reclined if the vehicle is moving.

Manual Reclining Seatbacks

{Warning

If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.

To recline the seatback:

1.Lift the lever.

2.Move the seatback to the desired position, and then release the lever to lock the seatback in place.

3.Push and pull on the seatback to make sure it is locked.

To return the seatback to the upright position:

1.Lift the lever fully without applying pressure to the seatback, and the seatback will return to the upright position.

2.Push and pull on the seatback to make sure it is locked.

Power Reclining Seatbacks

.Tilt the top of the control rearward to recline.

.Tilt the top of the control forward to raise.

Memory Seats

If equipped, memory seats allow two drivers to save and recall their unique seat positions for driving the vehicle, and a shared exit position for getting out of the vehicle. Other feature positions may also be saved, such as power mirrors and power steering wheel, if equipped. Memory positions are linked to RKE transmitter 1 or 2 for automatic memory recalls.

Before saving, adjust all available memory feature positions. Turn the vehicle on and then press and release SET; a beep will sound.

Then immediately press and hold 1, 2, or B (Exit) until two beeps sound. To manually recall these positions, press and hold 1, 2, or B until the saved position is reached. Follow the instructions under “Saving Memory Positions.”

The vehicle identifies the current driver’s RKE transmitter number (1– 8). See Remote Keyless Entry (RKE) System Operation 0 8. Only RKE transmitters 1 and 2 can be used for automatic memory recalls. A Driver Information Center (DIC) welcome message indicating the transmitter number may display for the first few ignition cycles following a transmitter change. For Seat Entry Memory to work properly, save the positions to the memory button (1 or 2) matching the RKE transmitter number displayed in the DIC welcome message. Carry the linked RKE transmitter when entering the vehicle.

Vehicle Personalization Settings

.To have the Seat Entry Memory movement begin when the vehicle is started, select the Settings menu, then Vehicle, then Seating Position, and then Seat Entry Memory. Select On or Off. See “Seat Entry Memory” later in this section.

.To begin Seat Exit Memory movement when the vehicle is turned off and the driver door is opened, or when the vehicle is turned off with the driver door already opened, select the Settings menu, then Vehicle, then Seating Position, and then Seat Exit Memory. Select On or Off. See “Seat Exit Memory” later in this section.

.See Vehicle Personalization

0 137 for additional setting information.

Identifying Driver Number

To identify the driver number:

1.Move your RKE transmitter away from the vehicle.

2.Start the vehicle with another key or RKE transmitter. The DIC should display the driver number for the other RKE transmitter. Turn the vehicle off and remove the key or RKE transmitter from the vehicle.

3.Start the vehicle with the initial key or RKE transmitter. The DIC should display the driver number of your RKE transmitter.

Saving Memory Positions

Read these instructions completely before saving memory positions.

To save preferred driving positions 1 and 2:

1.Turn the vehicle on or to ACC/ ACCESSORY.

A DIC welcome message may indicate driver number 1 or 2.

2.Adjust all available memory features to the desired driving position.

3.Press and release SET; a beep will sound.

4.Immediately press and hold the 1 or 2 memory button matching the above DIC welcome message until two beeps sound.

If too much time passes between releasing SET and pressing 1, the memory position will not be saved and two beeps will not sound. Repeat Steps 3 and 4.

1 or 2 corresponds to the driver number. See “Identifying Driver Number” previously in this section.

5.Repeat Steps 1–4 for a second driver using 1 or 2.

To save the position for B and Seat Exit Memory features, repeat Steps 1–4 using B. This saves the position for getting out of the vehicle.

Save preferred memory feature positions to both 1 and 2 if you are the only driver.

Manually Recalling Memory

Positions

Press and hold 1, 2, or B to recall the previously saved memory positions if you are driver 1 or 2 identified in the DIC welcome message. RKE transmitters 3–8 will not recall memory positions.

To stop Manual Memory recall movement, release 1, 2, or B or press any of the following controls:

.Power seat

.Memory SET

.Power mirror, with the driver or passenger side mirror selected

.Power steering wheel, if equipped

Seat Entry Memory

The vehicle identifies the number of the current driver’s RKE transmitter (1–8). See Remote Keyless Entry (RKE) System Operation 0 8. If the RKE transmitter is 1 or 2, and Seat Entry Memory is enabled in vehicle personalization, the positions saved to the same memory button number

1 or 2 are automatically recalled when the vehicle is turned on, or turned from off to ACC/

ACCESSORY. RKE transmitters 3–8 will not provide automatic memory recalls.

To turn Seat Entry Memory on or off, see “Vehicle Personalization Settings” previously in this section and Vehicle Personalization 0 137.

The shift lever must be in P (Park) to start Seat Entry Memory. Seat Entry Memory recall will complete if the vehicle is shifted out of P (Park) prior to reaching the saved memory position.

To stop Seat Entry Memory recall movement, turn the vehicle off or press any of the following controls:

.Power seat

.Memory SET, 1, 2, or B

.Power mirror, with the driver or passenger side mirror selected

.Power steering wheel, if equipped

If the saved memory seat position does not automatically recall or recalls to the wrong positions, the driver’s RKE transmitter number (1 or 2) may not match the memory button number that positions were saved to. Try storing the position to the other memory button or try the other RKE transmitter.

Seat Exit Memory

Seat Exit Memory is not linked to an RKE transmitter. The position saved

to B is used for all drivers. To turn Seat Exit Memory on or off, see «Vehicle Personalization Settings» previously in this section and

Vehicle Personalization 0 137.

If turned on, the position saved to B is automatically recalled when one of the following occurs:

.The vehicle is turned off and the driver door is opened within a short time.

.The vehicle is turned off with the driver door open.

To stop Seat Exit Memory movement, press any of the following memory controls:

.Power seat

.Memory SET, 1, 2, or B

.Power mirror, with the driver or passenger side mirror selected

.Power steering wheel, if equipped

Obstructions

If something has blocked the driver seat and/or power steering wheel while recalling a memory position, the recall may stop. Remove the obstruction and try the recall again. If the memory position still does not recall, see your dealer.

Heated and Ventilated

Front Seats

{Warning

If temperature change or pain to the skin cannot be felt, the seat heater may cause burns. To reduce the risk of burns, use care when using the seat heater, especially for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket, cushion, cover, or similar item. This may cause the seat heater to overheat. An overheated seat heater may cause a burn or may damage the seat.

Heated and Ventilated Seat

Buttons Shown, Heated Seat

Buttons Similar

If equipped, the buttons are near the climate controls on the center stack. To operate, the engine must be running.

Press L or M to heat the driver or passenger seat.

Press { or C, if available, to ventilate the driver or passenger seat. A ventilated seat has a fan that pulls or pushes air through the seat. The air is not cooled.

Press the button once for the highest setting. With each press of the button, the seat will change to the next lower setting, and then to the off setting. The indicator lights next to the buttons indicate three for the highest setting and one for the lowest. If the heated seats are on high, the level may automatically be lowered after approximately

30 minutes.

The passenger seat may take longer to heat up.

Auto Heated and Ventilated Seats

When the vehicle is on, this feature will automatically activate the heated or ventilated seats at the level required by the vehicle’s interior temperature.

The active high, medium, low, or off heated or ventilated seat level will be indicated by the manual heated or ventilated seat buttons on the center stack. Use the manual heated or ventilated seat buttons on the center stack to turn auto heated or ventilated seats off. If the passenger seat is unoccupied, the

auto heated or ventilated seats feature will not activate that seat. The auto heated or ventilated seats feature can be programmed to always be enabled when the vehicle is on.

See Vehicle Personalization 0 137.

Remote Start Heated and

Ventilated Seats

During a remote start, the heated or ventilated seats, if equipped, can be turned on automatically. When it is cold outside, the heated seats will turn on followed by the heated steering wheel, if equipped. When it is hot outside, the ventilated seats turn on. The remote start heated or ventilated seats may be canceled when the ignition is turned on. Press the heated or ventilated seat button to use the heated or ventilated seats after the vehicle is started.

The heated or ventilated seat indicator lights may not turn on during a remote start.

The temperature performance of an unoccupied seat may be reduced. This is normal.

The remote start heated or ventilated seats may be enabled or disabled in the vehicle personalization menu. See Remote Vehicle Start 0 15 and

Vehicle Personalization 0 137.

Rear Seats

Rear Seat Reminder

If equipped, the message REAR SEAT REMINDER LOOK IN REAR SEAT displays under certain conditions indicating there may be an item or passenger in the rear seat. Check before exiting the vehicle.

This feature will activate when a second row door is opened while the vehicle is on or up to 10 minutes before the vehicle is turned on. There will be an alert when the vehicle is turned off. The alert does not directly detect objects in the rear seat; instead, under certain conditions, it detects when a rear door is opened and closed, indicating that there may be something in the rear seat.

The feature is active only once each time the vehicle is turned on and off, and will require reactivation by opening and closing the second row doors. There may be an alert even when there is nothing in the rear seat; for example, if a child entered

the vehicle through the rear door and left the vehicle without the vehicle being shut off.

The feature can be turned on or off. See Vehicle Personalization 0 137.

Rear Seat Adjustment

The second row seats slide forward for more room.

To adjust the seat position:

1.Remove objects on the floor in front of or on the second row seat, or in the seat tracks on the floor.

2.Lift the lever below the seat cushion and slide the seat forward or backward.

Entering and Exiting the

Third Row

{Warning

Using the third row seating position while the second row is folded could cause injury in a sudden stop or crash. Be sure to return the seat to the passenger seating position. Push and pull on the seat to make sure it is locked into place.

{Warning

If the seatback and seat base are not locked, the seat could move forward in a sudden stop or crash and injure the occupant. Always push and pull on the seatbacks to be sure the seatback and seat base are locked.

Caution

Folding a rear seat with the seat belts still fastened may cause damage to the seat or the seat belts. Always unbuckle the seat belts and return them to their normal stowed position before folding a rear seat.

To access the third row from the driver side (bench seat only):

2009

2010

2011

2012

2013

2014

2015

2016

2017

2018

2020

2021

2022