Киа соренто 2020 инструкция по эксплуатации

Thank you for choosing a Kia vehicle.

When you require service, remember that your Kia dealer knows your vehicle best. Your dealer has factory-trained technicians, recommended special tools and genuine Kia replacement parts. It is dedicated to your complete customer satisfaction.

Because subsequent owners require this important information as well, this publication should remain with the vehicle if it is sold.

This manual will familiarize you with operational, maintenance and safety information about your new vehicle. It is supplemented by a Warranty and Consumer Information manual that provides important information on all warranties regarding your vehicle.

We urge you to read these publications carefully and follow the recommendations to help assure enjoyable and safe operation of your new vehicle.

Kia offers a great variety of options, components and features for its various models. Therefore, some of the equipment described in this manual, along with the various illustrations, may not be applicable to your particular vehicle.

The information and specifications provided in this manual were accurate at the time of printing. Kia reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation. If you have questions, always check with your Kia dealer.

We assure you of our continuing interest in your motoring pleasure and satisfaction in your Kia vehicle.

© 2019 Kia MOTORS AMERICA, Inc.

All rights reserved. May not be reproduced or translated in whole or in part without the written consent of Kia Motors America, Inc.

Printed in U.S.A.

Introduction

HOW TO USE THIS MANUAL

We want to help you get the greatest possible driving pleasure from your vehicle. Your Owner’s Manual can assist you in many ways. We strongly recommend that you read the entire manual. In order to minimize the chance of death or injury, you must read the WARNING and CAUTION sections in the manual.

Illustrations complement the words in this manual to best explain how to enjoy your vehicle. By reading your manual, you will learn about features, important safety information, and driving tips under various road conditions.

The general layout of the manual is provided in the Table of Contents. Use the index when looking for a specific area or subject; it has an alphabetical listing of all information in your manual.

Sections: This manual has eight sections plus an index. Each section begins with a brief list of contents so you can tell at a glance if that section has the information you want.

You will find various WARNINGs, CAUTIONs, and NOTICEs in this manual. All procedures and recommendations provided in these WARNINGs, CAUTIONs, and NOTICEs were prepared to enhance your personal safety and should be carefully read and followed.

WARNING

A WARNING indicates a situation in which harm, serious bodily injury or death could result if the warning is ignored.

CAUTION

A CAUTION indicates a situation in which damage to your vehicle could result if the caution is ignored.

NOTICE

A NOTICE indicates interesting or helpful information is being provided.

FUEL REQUIREMENTS

Your new vehicle is designed to use only unleaded fuel having a pump octane number ((R+M)/2) of 87 (Research Octane Number 91) or higher. (Do not use methanol blended fuels.)

Your new vehicle is designed to obtain maximum performance with UNLEADED FUEL, as well as minimize exhaust emissions and spark plug fouling.

Never add any fuel system cleaning agents to the fuel tank other than what has been specified. (Consult an authorized Kia dealer for details.)

•Tighten the cap until it clicks one time, otherwise the Check Engine light will illuminate.

WARNING — Refueling

•Do not «top off» after the nozzle automatically shuts off. Attempts to force more fuel into the tank can cause fuel overflow onto you and the ground causing a risk of fire.

•Always check that the fuel cap is installed securely to prevent fuel spillage, especially in the event of an accident.

Gasoline containing alcohol and methanol

Gasohol, a mixture of gasoline and ethanol (also known as grain alcohol), and gasoline or gasohol containing methanol (also known as wood alcohol) are being marketed along with or instead of leaded or unleaded gasoline.

Pursuant to EPA regulations, ethanol may be used in your vehicle.

Do not use gasohol containing more than 15% ethanol, and do not use gasoline or gasohol containing any methanol. Ethanol provides less energy than gasoline and it attracts water, and it is thus likely to reduce your fuel efficiency and could lower your MPG results.

Methanol may cause drivability problems and damage to the fuel system, engine control system and emission control system.

Discontinue using gasohol of any kind if drivability problems occur.

Vehicle damage or drivability problems may not be covered by the manufacturer’s warranty if they result from the use of:

1.Gasoline or gasohol containing methanol.

2.Leaded fuel or leaded gasohol.

3.Gasohol containing more than 15 percent ethanol

«E85» fuel is an alternative fuel comprised of 85 percent ethanol and 15 percent gasoline, and is manufactured exclusively for use in Flexible Fuel Vehicles. “E85” is not compatible with your vehicle. Use of “E85” may result in poor engine performance and damage to your vehicle’s engine and fuel system. Kia recommends that customers do not use fuel with an ethanol content exceeding 15 percent.

NOTICE

Your New Vehicle Limited Warranty does not cover damage to the fuel system or any performance problems caused by the use of “E85” fuel.

NOTICE

Never use any fuel containing methanol. Discontinue use of any methanol containing product which may inhibit proper drivability.

Other fuels

Using fuels that contain Silicone (Si), MMT (Manganese, Mn), Ferrocene (Fe), and Other metalic additives, may cause vehicle and engine damage or cause misfiring, poor acceleration, engine stalling, catalyst melting, clogging, abnormal corrosion, life cycle reduction, etc.

Also, the Malfunction Indicator Lamp (MIL) may illuminate.

NOTICE

Damage to the fuel system or performance problem caused by the use of these fuels may not be covered by your New Vehicle Limited Warranty.

Gasoline containing MMT

Some gasoline contains harmful man- ganese-based fuel additives Such as M M T ( M e t hy l c y c l o p e n t a d i e ny l Manganese Tricarbonyl). Kia does not recommend the use of gasoline containing MMT. This type of fuel can reduce vehicle performance and affect your emission control system. The Malfunction Indicator Lamp on the cluster may come on.

Do not use methanol

Fuels containing methanol (wood alcohol) should not be used in your vehicle. This type of fuel can reduce vehicle performance and damage components of the fuel system, engine control system and emission control system.

Fuel Additives

Kia recommends that you use good quality gasolines treated with detergent additives such as TOP TIER Detergent Gasoline, which help prevent deposit formation in the engine. These gasolines will help the engine run cleaner and enhance performance of the Emission Control System. For more information on TOP TIER Detergent Gasoline, please go to the website (www.toptiergas.com)

For customers who do not use TOP TIER Detergent Gasoline regularly, and have problems starting or the engine does not run smoothly, additives that you can buy separately may be added to the gasoline.

If TOP TIER Detergent Gasoline is not available, one bottle of additive should be added to the fuel tank at every 7,500miles or every engine oil change is recommended. Additives are available from your authorized Kia dealer along with information on how to use them. Do not mix other additives.

Operation in foreign countries

If you are going to drive your vehicle in another country, be sure to:

•Observe all regulations regarding registration and insurance.

•Determine that acceptable fuel is available.

VEHICLE HANDLING INSTRUCTIONS

As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control, an accident or vehicle rollover.

Specific design characteristics (higher ground clearance, track, etc.) give this vehicle a higher center of gravity than other types of vehicles. In other words they are not designed for cornering at the same speeds as conventional 2-wheel drive vehicles. Avoid sharp turns or abrupt maneuvers. Again, failure to operate this vehicle correctly may result in loss of control, an accident or vehicle rollover. Be sure to read the

“Reducing the risk of a rollover” driving guidelines, in section 5 of this manual.

Introduction

VEHICLE MODIFICATIONS

This vehicle should not be modified. Modification of your vehicle could affect its performance, safety or durability and may even violate governmental safety and emissions regulations.

In addition, damage or performance problems resulting from any modification may not be covered under warranty.

•If you use unauthorized electronic devices, it may cause the vehicle to operate abnormally, wire damage, battery discharge and fire. For your safety, do not use unauthorized electronic devices.

This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as:

•How various systems in your vehicle were operating;

•Whether or not the driver and passenger safety belts were buckled/ fastened;

•How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,

•How fast the vehicle was traveling.

INSTRUMENT PANEL OVERVIEW

The actual shape may differ from the illustration.

Your vehicle at a glance

OUMA018004

Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

• Front seat adjustment — manual. . . . . . . . . . . . . . . . . . 3-5

• Front seat adjustment — power. . . . . . . . . . . . . . . . . . . 3-7

• Driver position memory system (for power seat). . . 3-10

• Headrest (for front seat) . . . . . . . . . . . . . . . . . . . . . . . 3-12

• Seatback pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

• Rear seat adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

• Headrest (for rear seat). . . . . . . . . . . . . . . . . . . . . . . . 3-22

Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

• Seat belt restraint system . . . . . . . . . . . . . . . . . . . . . . 3-26

• Pre-tensioner seat belt. . . . . . . . . . . . . . . . . . . . . . . . . 3-33

• Seat belt precautions. . . . . . . . . . . . . . . . . . . . . . . . . . 3-35

• Care of seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37

Child restraint system . . . . . . . . . . . . . . . . . . . . . . 3-38

• Using a child restraint system . . . . . . . . . . . . . . . . . . 3-39

Air bag — Advanced supplemental

restraint system . . . . . . . . . . . . . . . . . . . . . . . . . . 3-46

• How does the air bag system operate . . . . . . . . . . . . 3-47

• Air bag warning light . . . . . . . . . . . . . . . . . . . . . . . . . 3-49

• SRS components and functions . . . . . . . . . . . . . . . . . 3-50

• Occupant Detection System (ODS) . . . . . . . . . . . . . . 3-53

• Driver’s and passenger’s front air bag . . . . . . . . . . . 3-59 3

• Side air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61

• Curtain air bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63

• SRS Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-70

• Adding equipment to or modifying your

air bag-equipped vehicle. . . . . . . . . . . . . . . . . . . . . . 3-71

• Air bag warning label . . . . . . . . . . . . . . . . . . . . . . . . . 3-71

Safety features of your vehicle

SEATS

■ Manual seat

■ Power seat

Front seat

(1)Forward and backward

(2)Seatback angle

(3)Seat cushion height*

(4)Lumbar support (Driver’s seat)*

(5)Cushion extension (Driver’s seat)*

(6)Driver position memory system*

(7)Headrest

(8)Walk-in switch (passenger’s seat)*

2nd row seat

(9)Forward and backward

(10)Seatback angle and folding

(11)Walk-in switch*

(12)Headrest

(13)Armrest

(14)Remote folding*

(15)Walk-in strap for emergency*

3rd row seat*

(16)Seatback folding

(17)Headrest

OUMA039001 * : if equipped

WARNING — Loose objects

Do not place anything in the driver’s foot well or under the front seats. Loose objects in the driver’s foot area could interfere with the operation of the foot pedals.

WARNING — Uprighting seat

Do not press the release lever on a manual seatback without holding and controlling the seatback. The seatback will spring upright possibly impacting you or other passengers.

WARNING — Driver responsibility for passengers

1KMN3662

The driver must advise the passenger to keep the seatback in an upright position whenever the vehicle is in motion. If a seat is reclined during an accident, the occupant’s hips may slide under the lap portion of the seat belt, applying great force to the unprotected abdomen.

Safety features of your vehicle

WARNING — Seat cushion

Occupants should never sit on aftermarket seat cushions or sitting cushions. The passenger’s hips may slide under the lap portion of the seat belt during an accident or a sudden stop.

WARNING — Driver’s seat

•Never attempt to adjust the seat while the vehicle is moving. This could result in loss of control of your vehicle.

•Do not allow anything to interfere with the normal position of the seatback and seatback adjustment.

•Sit as far back as possible from the steering wheel while still maintaining comfortable control of the your vehicle. A distance of at least 10″ from your chest to the steering wheel is recommended. Failure to do so can result in air bag inflation injuries to the driver.

3 3

Safety features of your vehicle

WARNING — Rear seatbacks

Always lock the rear seatback before driving. Failure to do so could result in passengers or objects being thrown forward injuring vehicle occupants.

WARNING — Luggage and Cargo

Do not stack pile or stack luggage or cargo higher than the seatback in the cargo area. In an accident the cargo could strike and injury a passenger. If objects are large, heavy or must be piled, they must be secured in the cargo area.

WARNING — Cargo Area

Do not allow passengers to ride in the cargo area under any circumstance. The cargo area is solely for the purpose of transporting luggage or cargo.

WARNING — Unexpected Seat Movement

After adjusting a manual seat, always check that it is locked by shifting your weight to the front and back. Sudden or unexpected movement of the driver’s seat could cause you to lose control of the vehicle.

WARNING — Seat

adjustment

•Do not adjust the seat while wearing seat belts. Moving the seat forward will cause strong pressure on the abdomen.

•Do not place your hand near the seat bottom or seat track while adjusting the seat. Your hand could get caught in the seat mechanism.

WARNING — Small Objects

Use extreme caution when picking small objects trapped under the seats or between the seat and the center console. Your hands might be cut or injured by the sharp edges of the seats mechanism.

Feature of Seat Leather

•Leather is made from the outer skin of an animal, which goes through a special process to be available for use. Since it is a natural substance, each part differs in thickness or density.

Wrinkles may appear as a natural result of stretching and shrinking depending on the temperature and humidity.

•The seat cover is made of stretchable material to improve comfort of passengers.

•The parts contacting the body are curved and the side supporting area is high which provides driving comfort and stability.

•Wrinkles may appear naturally from usage and is normal.

CAUTION

•Belts with metallic accessories, zippers or keys inside the back pocket may damage the seat fabric.

•Make sure not to wet the seat. It may change the nature of natural leather.

•Jeans or clothes which could bleach may contaminate the surface of the seat covering fabric.

NOTICE

Wrinkles or abrasions which appear naturally from usage are not covered by warranty.

Front seat adjustment — manual

Forward and backward

OUM038002

To move the seat forward or backward:

1.Pull the seat slide adjustment lever up and hold it.

2.Slide the seat to the position you desire.

3.Release the lever and make sure the seat is locked in place.

Adjust the seat before driving, and make sure the seat is locked securely by trying to move forward and backward without using the lever. If the seat moves, it is not locked properly.

OUM038004

To recline the seatback:

1.Lean forward slightly and lift up the seatback recline lever.

2.Carefully lean back on the seat and adjust the seatback of the seat to the position you desire.

3.Release the lever and make sure the seatback is locked in place. (The lever MUST return to its original position for the seatback to lock.)

OUM038003

To change the height of the seat, push the lever upwards or downwards.

•To lower the seat cushion, push the lever down several times.

•To raise the seat cushion, pull the lever up several times.

OUM038068

The lumbar support can be adjusted by pressing the lumbar support switch on the side of the seat.

1.Press the front portion of the switch to increase support, or the rear portion of the switch, to decrease support.

2.Release the switch once it reaches the desired position.

Front seat adjustment — power (if equipped)

The front seat can be adjusted by using the control switches located on the outside of the seat cushion. Before driving, adjust the seat to the proper position so you can easily control the steering wheel, pedals and switches on the instrument panel.

WARNING — Unattended children

Do not leave children unattended in the vehicle. Children might operate features of the vehicle that could injure them.

CAUTION — Power seat adjustments

The power seating controls function by electronic motor.

Excessive operation may cause damage to the electrical equipment.

OUM038072

Press the front portion of the switch to raise the cushion extension, or the rear portion of the switch to lower it. Release the switch once the cushion extension reaches the desired position.

OUMA038115

Push the control switch forward or backward to move the seatback to the desired angle. Release the switch once the seat reaches the desired position.

OUM038008

Pull the front portion of the control switch up to raise or press down to lower the front part of the seat cushion. Pull the rear portion of the control switch up to raise or press down to lower the rear part of the seat cushion. Release the switch once the seat reaches the desired position.

Walk-in Seat (for front passenger seat, if equipped)

OUM036096L

The switch is located on the left side of the front passenger’s seatback.

To adjust the position of front passenger’s seat ;

Press the control switch forward (1) or rearward (2)to move the seat to the desired position.

Press the control switch forward (3) or rearward (4) to move the seatback to the desired angle.

Do not use these switches while the front passenger seat is occupied.

Lumbar support (if equipped)

■ Driver seat

OUM038009

■ Passenger seat

OUM038113

The lumbar support can be adjusted by pressing the lumbar support switch on the side of the seat.

Type A (for Driver and Passenger seat)

1.Press the front portion of the switch to increase support, or the rear portion of the switch, to decrease support.

2.Release the switch once it reaches the desired position.

Safety features of your vehicle

WARNING

Never attempt to operate the driver position memory system while the vehicle is moving.

This could result in loss of control, and an accident causing death, serious injury.

Storing positions into memory using the buttons on the door

Storing driver’s seat positions

1.Shift the shift lever into P while the engine start/stop button is ON or ignition switch ON.

2.Adjust the driver’s seat and outside rearview mirror comfortable for the driver.

3.Press SET button on the control panel. The system will beep once.

4.Press one of the memory buttons (1 or 2) within 5 seconds after pressing the SET button. The system will beep twice when memory has been successfully stored.

When recalling an adjustment memory button while sitting in the vehicle, you can be surprised by the setting chosen if the memory has been adjusted by someone else. If that occurs, immediately push the seat position control knob in the direction of the desired position to stop further undesired movement.

Recalling positions from memory

1.Shift the shift lever into P while the engine start/stop button is ON or ignition switch ON.

2.To recall the position in the memory, press the desired memory button (1 or 2). The system will beep once, then the driver’s seat will automatically adjust to the stored position.

Adjusting the control switch for the driver’s seat while the system is recalling the stored position will cause the movement to stop and move in the direction that the control switch is moved.

Easy access function (if equipped)

The system will move the driver’s seat automatically as follows:

•Without smart key system

—It will move the driver’s seat rearward when the ignition key is removed.

—It will move the driver’s seat forward when the ignition key is inserted.

•With smart key system

—It will move the driver’s seat rearward when the engine start/stop button is changed to the OFF position.

—It will move the driver’s seat forward when the engine start/stop button is changed to the ACC or START position.

You can activate or deactivate this feature. Refer to «User settings» in chapter 4.

Headrest (for front seat)

OHM038048N

The driver’s and front passenger’s seats are equipped with a headrest for the occupant’s safety and comfort.

The headrest not only provides comfort for the driver and front passenger, but also helps protect the head and neck in the event of a rear collision.

For maximum effectiveness in case of an accident, the headrest should be adjusted so the middle of the headrest is at the same height of the center of gravity of an occupant’s head. Generally, the center of gravity of most people’s head is similar with the height of the top of their eyes. Also, adjust the headrest as close to your head as possible. For this reason, the use of a cushion that holds the body away from the seatback is not recommended.

WARNING — Headrest

removal/adjustment

•Do not operate the vehicle with the headrests removed. Headrests can provide critical neck and head support in a crash.

•Do not adjust the headrest height while the vehicle is in motion. Driver may lose control of the vehicle.

Adjusting the height up and down

■ Type A

OUM038011

■ Type B

OUMA038200

To raise the headrest, pull it up to the desired position (1). To lower the headrest, push and hold the release button (2) on the headrest support and lower the headrest to the desired position (3).

OYFH034205

NOTICE

If you recline the seatback towards the front with the headrest and seat cushion raised, the headrest may come in contact with the sunvisor or other parts of the vehicle.

Removal and reinstallation

■ Type A

OUM038012

■ Type B

OUM038013

To remove the headrest:

1.Recline the seatback (2) with the recline lever or switch (1).

2.Raise headrest as far as it can go.

3.Press the headrest release button

(3) or press the release button with slim tool (3) (for Type C and Type D) while pulling the headrest up.

WARNING

NEVER allow anyone to ride in a seat with the headrest removed or reversed.

OUMA038012

OUMA038201

■ Type A

OUM038014

■ Type B

OUM038015

To reinstall the headrest :

1.Put the headrest poles (2) into the holes while pressing the release button (1) or pressing the release button with slim tool (1,for Type C and D).

Forward and backward (2nd row seat)

OUM034017

To move the seat forward or backward:

1.Pull the seat slide adjustment lever up and hold it.

2.Slide the seat to the position you desire.

3.Release the lever and make sure the seat is locked in place.

Adjust the seat before driving, and make sure the seat is locked securely by trying to move forward and backward without using the lever. If the seat moves, it is not locked properly.

OUM034018

To recline the seatback:

1.Pull up the seatback recline lever (for 2nd row outboard seat).

2.Hold the lever and adjust the seatback of the seat to the position you desire.

3.Release the lever and make sure the seatback is locked in place. (The lever MUST return to its original position for the seatback to lock.)

OUM034022/H

OUMA039023

OUMA039209

To get in or out of the 3rd row seat,

1.Routing the seat belt webbing through the rear seat belt guide clip.

After inserting the seat belt, tighten the belt webbing by pulling it up.

2.Push the walk-in switch located in upper part (1) of 2nd row seat or side part (2) of 2nd row seat.

3.The 2nd row seatback will be folded and push the seat to the farthest forward position.

After getting in or out, slide the 2nd row seat to the farthest rearward position and pull the seatback firmly backward until it clicks into place. Make sure that the seat is locked in place.

WARNING

Never attempt to adjust using the 2nd row seat walk-in switch or strap while the vehicle is moving or seat is occupied as the seat may suddenly move and cause the passenger on the seat to be injured.

WARNING

OUMA039210

•If the walk-in switch does not work, pull the strap (3) located on the lower left side of the seat. Then you can move the 2nd row seat forward. (7 passenger vehicle — Right seat : lower left side,)

•Never attempt to pull the strap

(3)while the 2nd row seat is occupied as the seat may suddenly move and cause the passenger on the seat to be injured. Use only the strap when the walk-in switch does not work.

Safety features of your vehicle

Folding the rear seat

The rear seatbacks can be folded to facilitate carrying long items or to increase the luggage capacity of the vehicle.

WARNING — Objects

Objects carried on the folded down seatback should not extend higher than the top of the front seatbacks. This could allow cargo to slide forward and cause injury or damage during sudden stops.

WARNING

Never allow passengers to sit on top of the folded down seatback while the vehicle is moving. This is not a proper seating position since the seat has important crash protection features and seat belts are not available in this seat configuration. This could result in serious injury or death in case of an accident or sudden stop.

Safety features of your vehicle

To fold down the rear seatback

1.Insert the rear seat belt buckle in the pocket between the rear seatback and cushion, and insert the rear seat belt webbing in the guide to prevent the seat belt from being damaged.

2.Set the front seatback to the upright position and if necessary, slide the front seat forward.

3.Lower the rear headrests to the lowest position.

Turn off the rear seat warmer (if equipped) when you fold the 2nd row seatback.

Safety features of your vehicle

4.Pull on the seatback folding lever for 2nd row seat or strap for 3rd row seat, then fold the seat toward the front of the vehicle. When you return the seatback to its upright position, always be sure it has locked into position by pushing on the top of the seatback.

5.To use the rear seat, lift and pull the seatback backward by pulling on the folding lever or strap.

Pull the seatback firmly until it clicks into place.

Make sure the seatback is locked in place.

6.Return the rear seat belt to the proper position.

Safety features of your vehicle

2nd row seat folding (from outside, if equipped)

OUMA034030

Pull the 2nd row seat back folding lever out.

The 2nd row seat back will be folded.

If you pull the left side lever (1) out, left side seat back and center seat back will be folded.

If you pull the right side lever (2) out, right side seat back will be folded.

WARNING — Rear seat folding

Do not fold the rear seats (2nd & 3rd row seats), if passengers, pets or luggage are in the rear seats.

It may cause injury or damage to passengers, pets or luggage.

To fold down the rear center seatback (for 2nd row seat)

OUM034031L

1.Lower the rear headrests to the lowest position.

2.Push the center seatback folding lever up, then fold the seat toward the front of the vehicle.

When you return the seatback to its upright position, always be sure it has locked into position by pushing on the top of the seatback.

Remember to return the rear shoulder belts to their proper position. Routing the seat belt webbing through the rear seat belt guides will help keep the belts from being trapped behind or under the seats.

WARNING — 2nd row center seat folding

•Do not fold the 2nd row center seat, if there are occupants in the 3rd row seats, as this may result in injury to occupants if the seat moves during a collision. If occupants are seated in the 3rd row seats, fix the 2nd row center seat in its upright and locked position.

•The 2nd row center seat back does not lock into position when it is folded toward the front of the vehicle. If you use the 2nd row center seat back folding function to carry long objects, you should fix the long object to prevent it from being thrown about the vehicle in a collision and causing injury to vehicle occupants.

Safety features of your vehicle

CAUTION — Damaging rear seat belt buckles

When you fold the rear (2nd and/or 3rd row) seatback, insert the buckle in the pocket between the rear seatback and cushion. Doing so can prevent the buckle from being damaged by the rear seatback.

WARNING — Cargo

Do not place objects in the rear (2nd and/or 3rd row) seats, since they cannot be properly secured and may hit the front seat occupants in a collision. Cargo should always be secured to prevent it from being thrown around in the vehicle in a collision causing injuries to vehicle occupants.

OUN026140

WARNING — 3rd row seat

3rd row occupants should always remain in the center of the seat cushion so the occupants head is protected by the headrest.

Failure to heed this warning could allow an occupants head to be injured by a closing tailgate, which could result in severe personal injury.

Generally, the center of gravity of most people’s head is similar with the height of the top of their eyes.

Also adjust the headrest as close to your head as possible. For this reason, the use of a cushion that holds the body away from the seatback is not recommended.

Adjusting the height up and down (for 2nd row seats)

■ Outside

OUM034019L

■ Center

OUMA034092

To raise the headrest :

1. Pull it up to the desired position (1).

To lower the headrest :

1.Push and hold the release button

(2) on the headrest support

2.Lower the headrest to the desired position (3).

Safety features of your vehicle

WARNING

•Make sure the headrest locks in position after adjusting it to properly protect the occupants.

•After installing the headrest, make sure that it is installed in the right direction.

A headrest installed reversely could increase whiplash injury during rear impact.

3rd row headrest (if equipped)

OUMA034091

OXM039061N

The headrest will fold down automatically when folding the seatback.

To fold the headrest manually : Pull the strap.

To unfold the headrest :

Raise the headrest manually.

Always be sure the headrest has locked into position after you return the seatback.

Safety features of your vehicle

SEAT BELTS

Seat belt restraint system

•For maximum restraint system protection, the seat belts must always be used whenever the vehicle is moving. A properly positioned shoulder belt should be positioned midway over your shoulder across your collarbone.

•Never allow children to ride in the front passenger seat. See child restraint system section for further discussion.

WARNING — Twisted seat belt

Make sure your seat belt is not twisted when worn. A twisted seat belt may not properly protect you in an accident and could lead to severe personal injuries, lacerations, and even death.

WARNING — Shoulder Belt

•Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt cannot protect the occupant in a crash.

•Always wear both the shoulder portion and lap portion of the lap/shoulder belt.

WARNING — Damaged seat belt

Replace the entire seat belt assembly if any part of the webbing or hardware is damage as you can no longer be sure that a damage seat belt will provide protection in a crash.

Seat belts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided.

Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed.

A slack belt will greatly reduce the protection afforded to the wearer.

Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged.

•No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack.

•When you fasten the seat belt, be careful not to latch the seat belt in buckles of other seat. It’s very dangerous and you may not be protected by the seat belt properly.

•Do not unfasten the seat belt and do not fasten and unfasten the seat belt repeatedly while driving. This could result in loss of control, and an accident causing death, serious injury, or property damage.

•When fastening the seat belt, make sure that the seat belt does not pass over objects that are hard or can break easily.

WARNING — Seat belt buckle

Do not allow foreign material (gum, crumbs, coins, etc.) to obstruct the seat belt buckle. This may prevent the seat belt from fastening securely.

Safety features of your vehicle

Seat belt warning (for driver’s seat)

1GQA2083

The driver’s seat belt warning light and chime will activate according to the following table when the ignition switch is in “ON” position.

Safety features of your vehicle

*1 Warning pattern repeats 11 times with an interval of 24 seconds. If the driver’s seat belt is buckled, the light will stop within 6 seconds and chime will stop immediately.

*2 The light will stop within 6 seconds and chime will stop immediately.

Seat belt — Driver’s 3-point system with emergency locking retractor

B180A01NF-1

To fasten your seat belt:

To fasten your seat belt, pull it out of the retractor and insert the metal tab

(1) into the buckle (2). There will be an audible «click» when the tab locks into the buckle.

WARNING

You should place the lap belt portion as low as possible and snugly across your hips, not on your waist. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration.

Never wear the seat belt under the arm near the door.

B200A02NF

The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly.

NOTICE

If you are not able to pull out the seat belt from the retractor, firmly pull the belt out and release it. Then you will be able to pull the belt out smoothly.

Front seat

OLM039026

Height adjustment

You can adjust the height of the shoulder belt anchor to one of the 3 positions for maximum comfort and safety.

The height of the adjusting seat belt should not be too close to your neck. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder near the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appropriate position.

To raise the height adjuster, pull it up

(1). To lower it, push it down (3) while pressing the height adjuster button

(2).

Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into position.

Improperly positioned seat belts can cause serious injuries in an accident.

WARNING — Shoulder belt positioning

Never position the shoulder belt across your neck or face.

WARNING — Seat belt replacement

Replace your seat belts after being in an accident. Failure to replace seat belts after an accident could leave you with damaged seat belts that will not provide protection in the event of another collision.

Safety features of your vehicle

CAUTION

Do NOT fold down the left portion of the rear seat back when the rear center seat belt is buckled. ALWAYS UNBUCKLE the rear center seat belt before folding down the left portion of the rear seat back. If the rear center seat belt is buckled when the left portion of the rear seat back is folded down, distortion and damage to the top portion of the seat back and seat belt garnish may result, causing the seat back to lock into the folded down position.

B210A01NF-1

To release the seat belt:

The seat belt is released by pressing the release button (1) on the locking buckle. When it is released, the belt should automatically draw back into the retractor.

If this does not happen, check the belt to be sure it is not twisted, then try again.

OUM038110L

The seat belt should be locked into the buckle on each seat cushion to be properly fastened.

: Rear right seat belt fastening buckle

: Rear center seat belt fastening buckle

: Rear left seat belt fastening buckle

OUM038111L

When using the rear center seat belt, the buckle with the “CENTER” mark must be used.

WARNING

Prior to fastening the rear seat belts, ensure the latch matches the seat belt buckle. Forcefully fastening the left or right seat belt to the center buckle can result in an improper fastening scenario that will not protect you in an accident.

• Уже зарегистрированы? Войти  

  Войти

  • 
    

    Запомнить меня

    
    Не рекомендуется на общедоступных компьютерах
    

  • 
    

    Войти анонимно

  • Забыли пароль?

• Регистрация