Инструкция nikon speedlight sb 800

En

SB-800 Autofocus Speedlight

Instruction Manual

i

For your safety

Before using your product, please read the following safety precautions carefully and thoroughly to ensure correct and safe use and to help prevent damage to your Nikon product or injury to yourself or others. For quick reference by those who use the product, please keep these safety instructions near the product.

In this manual, safety instructions are indicated with these symbols:

Disregarding instructions marked with this symbol could result in personal injury, or death and property damage.

Disregarding instructions marked with this symbol could result in property damage.

WARNING

CAUTION

Symbol for separate collection applicable in European countries

This symbol indicates that this product is to be collected separately. The following apply only to users in European countries.

This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste

For more information, contact the retailer or the local authorities in charge of waste management.

ii

WARNINGS for Speedlights

1 If corrosive liquids seep from the batteries and get in your eyes, immediately wash your eyes with running water and consult with a doctor. Your eyes could be seriously damaged if they are not treated quickly.

2 If corrosive liquids seep from the batteries and come in contact with your skin or clothes, wash immediately with running water. Prolonged contact could injure your skin.

3 Never attempt to disassemble or repair the flash unit by yourself, as this could result in you receiving an electric shock and could also cause the unit to malfunction; such malfunction could lead to personal injury.

4 If the flash unit is dropped and damaged, do not touch any exposed interior metal parts. Such parts, especially the speedlights capacitor and associated parts, could be in a high-charge state and if touched could cause an electric shock. Disconnect the power or remove the batteries and be sure that you do not touch any of the products electrical components, and then bring the flash unit to your local Nikon dealer or authorized service center for repair.

5 If you detect heat, smoke or notice a burning smell, immediately stop operation and remove the batteries to prevent the unit from catching on fire or melting. Allow the flash unit to cool down so that you can safely touch it and remove the batteries. Then bring the unit to your local Nikon dealer or authorized service center for repair.

6 The flash unit should never be submerged in liquid or exposed to rain, saltwater or moisture unless it is properly protected from the liquids and moisture. Underwater use requires a certified underwater housing. If water or moisture gets inside the unit, this could cause the unit to catch on fire or cause an electric shock. In such instances you should immediately remove the batteries from the speedlight and then bring the unit to your local Nikon dealer or authorized service center for repair. Note: electronic devices that are penetrated by water or moisture are often

not economically repairable. 7 Do not use the unit in the presence of flammable or explosive gas.

If the flash unit is operated in areas where there is a flammable gas, including propane, gasoline and dust, it could cause an explosion or fire.

8 Do not fire the flash unit directly at the driver of a moving car, as this could temporarily impair the drivers vision and cause an accident.

9 Do not fire the flash unit directly into the eyes of someone that is at close range, as it could damage their eyes retinas. Never fire the flash unit closer than 1 meter from infants.

P re

pa ra

tio n

iii

For your safety

10 Do not fire the unit while the flash head is touching a person or object. Such use can result in the person being burned, and/or their clothes igniting from the heat of the flashs firing.

11 Keep small accessories out of the reach of children to avoid the possibility of the accessory being swallowed. If an accessory is accidentally swallowed, immediately consult with a doctor.

12 Use only the batteries specified in this instruction manual. Batteries other than those specified could leak corrosive liquids, explode or catch on fire or otherwise not perform satisfactorily.

13 Do not mix battery types, brands or old and new batteries, as the batteries could leak corrosive liquids, explode or catch on fire. When using more than one battery in a product, always use identical batteries that were purchased at the same time.

14 Non-rechargeable batteries such as manganese, alkaline-manganese and lithium batteries should never be charged in a battery charger because they could leak corrosive liquids, explode or catch on fire.

15 When using standard size (AA, AAA, C, D) or other common rechargeable batteries such as NiCd and Ni-MH battery types, or when recharging them, be sure to use only the battery charger specified by the battery maker and read the instructions thoroughly. Do not recharge these batteries with their terminals reversed in the charger or before the batteries have cooled off sufficiently because they could leak corrosive liquids, explode or catch on fire. The same caution also applies to using the rechargeable batteries that may be supplied by the photo products manufacturer.

CAUTIONS for Speedlights

1 Do not touch the flash unit with wet hands, as this could cause an electric shock.

2 Keep the flash unit away from children to prevent them from putting the unit in or near their mouth, or otherwise touching a dangerous part of the product; as such contact could cause an electric shock.

3 Do not apply strong physical shocks to the unit, as this could cause a malfunction that could cause the unit to explode or catch on fire.

4 Never use active agents that contain flammable substances such as paint thinner, benzene or paint remover to clean the unit, and never store the unit in locations containing chemicals such as camphor and naphthalene, as this could damage the plastic case, cause a fire or cause an electric shock.

iv

5 Remove any batteries from the unit before storing the unit for a long time to prevent the unit from catching on fire or leaking corrosive liquids.

WARNINGS for Batteries

1 Never heat or throw batteries into a fire, as this could cause the batteries to leak corrosive liquids, generate heat or explode.

2 Do not short-circuit or disassemble the batteries because this could cause the batteries to leak corrosive liquids, generate heat or explode.

3 Do not mix battery types, brands or old and new batteries, as this could cause the batteries to leak corrosive liquids, generate heat or explode.

4 Do not install batteries in the reverse direction as this could cause the batteries to leak corrosive liquids, generate heat or explode. Even if only one battery is installed in reverse it will cause the speedlight to malfunction.

5 Be sure to use the battery charger specified by the battery maker to avoid the possibility of batteries leaking corrosive liquids, generating heat or exploding.

6 Do not carry or store batteries along with metallic materials such as necklaces and hair pins because such materials could cause the batteries to short-circuit, leading to battery leakage, heat generation or an explosion. In addition, specially when carrying a quantity of batteries, place them carefully in a storage case that prevents the battery terminals from touching another batterys terminals because if they touch in reverse order it could also cause the batteries to short-circuit, leading to battery leakage, heat generation or an explosion.

7 If corrosive liquids seep from the batteries and get in your eyes, immediately wash your eyes with running water and consult with a doctor. Your eyes could be seriously damaged if they are not treated quickly.

8 If corrosive liquids seep from the batteries and come in contact with your skin or clothes, wash immediately with running water. Prolonged contact could injure your skin.

9 Always follow the warnings and instructions printed on the batteries to avoid activities that could cause the batteries to leak corrosive liquids, generate heat or catch on fire.

10 Be sure to use only batteries specified in this instruction manual, to avoid the possibility of batteries leaking corrosive liquids, generating heat or exploding.

P re

pa ra

tio n

v

For your safety

11 Never open the casing surrounding batteries or use batteries whose casing has been breached as such batteries could leak corrosive liquids, generate heat or explode.

12 Keep batteries out of the reach of children to help avoid the possibility of them being swallowed. If a battery is accidentally swallowed, immediately consult with a doctor.

13 Batteries should not be submerged in water, exposed to rain, moisture or saltwater unless they are properly protected from the wet environment. If water or moisture gets inside the batteries, this could cause them to leak corrosive liquids or generate heat.

14 Do not use any battery that appears abnormal in any way, including a change in color or shape. Such batteries could leak corrosive liquids or generate heat.

15 Stop recharging rechargeable batteries if you notice that recharging is not completed within the specified time to help prevent the possibility of the battery leaking corrosive liquids or generating heat.

16 When recycling or disposing of batteries, be sure to insulate their terminals with tape. If the batterys positive and negative terminals short- circuit after coming into contact with metallic objects, it could cause fire, heat generation or an explosion. Dispose of used batteries in accordance with local government regulations.

17 Non-rechargeable batteries should never be charged in a battery charger because they could leak corrosive liquids or generate heat.

18 Remove dead batteries from your equipment immediately, as they could leak corrosive liquids, generate heat or explode.

CAUTION for Batteries

Do not throw or apply strong physical shocks to the batteries as this could cause batteries to leak corrosive liquids, generate heat or explode.

1

Contents

Preparation For your safety……………………………………………………………i-v Foreword ………………………………………………………………….4-6 Tips on using the Speedlight …………………………………………7 Camera groups and available flash modes ………………….8-9 Speedlight parts and their functions ………………………..10-11 Control buttons…………………………………………………………..12 Icons on the LCD panel………………………………………….13-15 Lenses………………………………………………………………………16

Basic operation ………………………………………………………..17 1 Installing the batteries …………………………………………..18-19 2 Test firing (Confirming the exposure) ………………………20-21 3 Attach the SB-800 to the camera and adjust

the flash head ……………………………………………………22-23 4 Setting the ISO sensitivity………………………………………24-25 5 Adjust the zoom-head position……………………………….26-27 6 Setting the cameras exposure mode and

metering system…………………………………………………28-29 7 Setting the SB-800s flash mode …………………………….30-31 8 Compose the picture and shoot with flash……………….32-33 Using the SB-800 with the COOLPIX………………………………34

Detailed operation…………………………………………………….35 SB-800s available flash modes ……………………………………36 TTL auto flash mode …………………………………………………..37 Non-TTL auto flash mode ……………………………………….38-41 Manual mode ………………………………………………………..42-50 Notes on continuous flash shooting………………………………51 Checking the correct exposure before shooting …………….52

Other functions ………………………………………………………..53 Exposure compensation and flash output level

compensation……………………………………………………..54-56 Flash-shooting distance range with zoom lenses

having a variable aperture ………………………………………..57 Slow-sync flash mode, Red-eye reduction control,

and Rear-curtain sync ………………………………………….58-59

2

Contents

Auto FP High-Speed Sync mode………………………………….60 Flash Value Lock (FV Lock) …………………………………………61 Autofocus flash operation in dim light ………………………62-63 Using the Quick Recycling Battery Pack SD-800 ………64-65 Checking the illumination before actually

taking the picture (Modeling illuminator)……………………..66 Custom functions ……………………………………………………….67 Custom settings …………………………………………………….68-70

Advanced operations………………………………………………..71 Overview of multiple flash operation ………………………..72-73 Wireless multiple flash shooting ………………………………74-75 Flash shooting in Advanced Wireless Lighting ………….76-83 SU-4 type wireless multiple flash shooting………………..84-88 Confirming wireless multiple flash operation

using the ready-light or the beeping sound…………………89 Multiple flash shooting using cords………………………….90-93 System chart for TTL multiple flash shooting

using cords…………………………………………………………94-95 Flash shooting with digital SLRs cameras

using colored gel filters………………………………………..96-97 Bounce flash operation…………………………………………98-101 Close-up flash operation……………………………………..102-105 Flash shooting in the 1/300 TTL High-Speed

Flash sync mode (F5 only) ………………………………………106

Reference information …………………………………………….107 TTL auto flash modes available

with the SB-800 ……………………………………………….108-110 Optional accessories ………………………………………….111-113 Tips on Speedlight care…………………………………………….114 Notes on batteries…………………………………………………….115 Troubleshooting………………………………………………….116-118 About the LCD panel ………………………………………………..119 Specifications…………………………………………………….120-123 Index ………………………………………………………………..124-125

3

Preparation

This section provides preliminary information on using the SB-800.

Basic operation

Basic procedures to take simple, properly exposed flash photographs in the TTL auto flash mode.

Detailed operation

A variety of flash modes available with the SB-800 are explained.

Other functions

Detailed information on each function of the SB-800 is provided.

Advanced operations

Information on advanced flash shooting techniques using the SB-800 is described.

Reference information

Optional accessories, Troubleshooting, Speedlight care, Specifications, etc. are presented in this section.

4

Foreword

Thank you for purchasing the Nikon Speedlight SB-800. To get the most out of your Speedlight, please read this instruction manual thoroughly before use. Also, read the separate booklet, A collection of example photos, which provides an overview of the SB-800s flash- shooting capabilities with example photos. In addition, keep your camera instruction manual handy for quick reference.

Main features and functions of the SB-800 The SB-800 is a high-performance Speedlight with a guide number of 38/125

(ISO 100, m/ft.) or 53/174 (ISO 200, m/ft.) (at the 35mm zoom-head position, 20C/68F.) According to the camera and lens combination used with the SB-800, you can perform various types of TTL auto flash (p. 37), Non-TTL auto flash (p. 38), and Manual flash (p. 42).

A power zoom function automatically adjusts the zoom-head position to match the lens focal length (with the exception of some camera/lens combinations) (p. 26). When the built-in wide-flash adapter is used or the Nikon Diffusion Dome is attached (p. 27), the zoom-head position is automatically set to match a 14mm or 17mm lens.

The flash head tilts up to 90 or down to 7 and rotates horizontally 180 to the left and 90 to the right, enabling bounce flash (p. 98) or close-up flash photography (p. 102).

The Nikon Creative Lighting System provides a variety of advanced wireless multiple flash operations when the SB-800 is used with compatible cameras (p. 5).

When doing bounce flash or taking close-ups with flash, you can use the built-in wide-flash adapter in conjunction with Nikon Diffusion Dome to create extremely soft, diffused lighting with virtually no shadows, while maintaining balanced lighting for the main subject and the background (pp. 101, 104).

Custom functions are provided to set values, or activate or cancel functions that are unnecessary to set each time (p. 67).

u Life-long learning As part of Nikons Life-long learning commitment to ongoing product support and education, continually-updated information is available on-line at the following sites: For users in the U.S.A.: http://www.nikonusa.com/ For users in Europe: http://www.europe-nikon.com/support For users in Asia, Oceania, the Middle East, and Africa: http://www.nikon-asia.com/ Visit these sites to keep up-to-date with the latest product information, tips, answers to frequently-asked questions (FAQs), and general advice on digital imaging and photography. Additional information may be available from the Nikon representative in your area. See the URL below for contact information:

http://nikonimaging.com/

5

The SB-800 features the Nikon Creative Lighting System (CLS). This system offers additional flash shooting possibilities with digital cameras by taking advantage of cameras digital communication capabilities. CLS is available only when the SB-800 is used with compatible Nikon cameras. The SB-800 offers these major features:

i-TTL mode This is a TTL auto flash mode in the Nikon Creative Lighting System. Monitor Preflashes are fired at all times. The subject is correctly exposed by the light from the flash lighting and the exposure is less affected by the ambient light (p. 37).

Advanced Wireless Lighting With the Advanced Wireless Lighting, wireless multiple flash operation in the TTL (i-TTL) mode can now be accomplished with digital SLRs. In this mode, you can divide the remote flash units into three groups and control the flash output independently for each group, expanding your range of creative multiple-flash shooting techniques (p. 76).

Flash Value Lock Flash Value, or FV, is the amount of flash exposure for the subject. Using FV Lock with compatible cameras, you can lock in the appropriate flash exposure for the main subject. This flash exposure is locked in, even if you change the aperture or composition, or zoom the lens in and out (p. 61).

Flash Color Information Communication When the SB-800 is used with compatible digital SLRs, color temperature information is automatically transmitted to the camera. In this way, the cameras white balance is automatically adjusted to give you the correct color temperature when taking photographs with the SB-800.

Auto FP High-Speed Sync High-Speed flash synchronization at your cameras highest shutter speed is now possible. This is useful when you want to use a wider aperture to achieve shallow depth of field to blur the background (p. 60).

Wide-Area AF-Assist Illuminator In autofocus operation, the SB-800 emits AF-Assist illumination over a wider area. This enables you to perform autofocus photography in dim light even when you change the cameras focus area with cameras supporting this function (p. 62).

See your equivalent cameras instruction manual for details on the Nikon Creative Lighting System.

P re

pa ra

tio n

Nikon Creative Lighting System

6

Foreword

Notes Default: Functions and flash modes preset when shipped from the factory

are referred to as Default settings in this manual. CLS: Hereafter, Nikons new Speedlight system Nikon Creative Lighting

System is abbreviated CLS.

Marks used in this manual

v: Denotes important points to prevent malfunction or shooting failure.

t: Useful points that should be remembered for better usage of the SB-800.

u: Provides convenient reference information when using the SB-800

Supplied accessories

Quick Recycling Battery Pack Speedlight Stand Nikon Diffusion Dome SD-800 AS-19 SW-10H

Colored Gel Filter Set SJ-800: Soft Case SS-800 FL-G1, TN-A1

7

Tips on using the Speedlight

Take trial shots Make trial shots before photographing important occasions like weddings or graduations.

Have Nikon spot-check your Speedlight regularly Nikon recommends that you have your Speedlight serviced by an authorized dealer or service center at least once every two years.

Using your Speedlight correctly The Nikon Speedlight SB-800s performance has been optimized for use with Nikon brand cameras/accessories including lenses. Camera/accessories made by other manufacturers may not meet Nikons criteria for specifications, and nonconforming cameras/accessories could damage the SB-800s components. Nikon cannot guarantee the SB-800s performance when used with non-Nikon products.

Notes: The Nikon N90s, N90, N75-Series, N70, N60, N55-Series, N50, N8008, N8008s,

PRONEA 6i, N6006, N6000, N5005, N4004s and N4004 are sold exclusively in the U.S.A.

The Nikon N80-Series, N65-Series are sold exclusively in the U.S.A. and Central and South America.

The Nikon N2020 and N2000 are sold exclusively in the U.S.A and Canada.

P re

pa ra

tio n

In this manual, Nikon cameras are divided into 10 groups, including cameras compatible with CLS*, digital SLRs not compatible with CLS* and cameras in Groups I to VII, unless otherwise noted. First, consult the camera group table to see which group your camera belongs to. Then as you read the manual, you will find specific information on how to use the SB-800 with your particular camera. *CLS: Nikon Creative Lighting System (p. 5)

8

Camera groups and available flash modes

*1 o: Balanced Fill-Flash. This always appears together with D (p. 37). *2 Wireless multiple flash in the i-TTL mode is possible. *3 TTL mode is not possible with digital SLR cameras.

TTL auto flash mode (p. 37)

Group Camera name D D D o i-TTL D-TTL TTL *1

Cameras D3, D2-Series, D300, D200, D80, compatible D70-Series, D60, D50, D40-Series, F6

with CLS*

Digital SLRs not D1-Series, D100

compatible with CLS*

F5, F100, F90X/N90s, F90-Series/N90, I F80-Series/N80-Series, F75-Series/

N75-Series, F70-Series/N70

F4-Series, F65-Series/N65-Series, II F-801s/N8008s, F-801/N8008,

Pronea 600i/6i

III F-601/N6006, F-601M/N6000 *5

IV F60-Series/N60, F50-Series/N50, *5

F-401x/N5005

V F-501/N2020, F-401s/N4004s, F-401/N4004, F-301/N2000

VI FM3A, FA, FE2, FG, Nikonos V, F3-Series (with the AS-17)

VII New FM2, FM10, FE10, F3-Series, F55-Series/N55-Series

COOLPIX cameras COOLPIX 8400, COOLPIX 8800, compatible COOLPIX P5000, COOLPIX P5100

with i-TTL

9

*4 Distance-priority manual flash p is not possible with D1X and D1H digital cameras. *5 While performing Balanced Fill-Flash, no o icon appears. *6 Repeating flash is not possible with the F3-Series (using the AS-17).

Non-TTL auto flash mode (p. 38) Manual mode ( p. 42) Wireless multiple flash

p Advanced B A Distance- G q Wireless SU-4 type Auto Non-TTL priority Manual Repeating Lighting (master flash)

Aperture flash auto flash manual flash flash (p. 76) (p. 84) flash

*2 *3

*4

*3

*6

The SB-800s available flash modes vary, depending on the cameras and lenses in use or the cameras exposure mode and metering system. For more details, refer to Detailed operation (p. 35), TTL auto flash modes available with the SB-800 (p.108) and your cameras instruction manual.

P re

pa ra

tio n

: Available : Not available

10

Speedlight parts and their functions

1 Control button quick reference (p. 12)

2 Flash head (p. 100) Can be tilted up to 90 or down to 7, and rotated horizontally 180 to the left and 90 to the right.

3 Flash head tilting/rotating lock release button (p. 22)

4 Light sensor window for wireless remote flash (p. 74) Setting the SB-800 as a remote flash unit (P. 76)

5 Battery chamber lid attachment indexes (p. 18)

6 Battery chamber lid (p. 18) 7 Built-in bounce card (p. 101)

Creates a highlight in the subjects eyes in bounce flash photography.

8 Built-in wide-flash adapter (p. 104) Increases the angle of coverage to match a 14mm or 17mm lens.

9 Wide-area AF-assist illuminator (p. 62) Automatically turns on for autofocus operation when the light is dim.

10 External power source terminal (supplied with cover) (p. 113)

11 Light sensor window for Non-TTL auto flash (p. 38) Senses reflected light from the subject in Auto Aperture B or Non-TTL auto A flash mode.

12 External AF-assist illuminator contacts (for SC-29) Accepts optional TTL Remote Cord SC-29

13 Mount pin 14 Hot-shoe contacts 15 Mounting foot

5 6

3 4

1

2

9

8

7

11

10

12 13

15

14

11

16 Flash head tilting angle scale (p. 100)

17 Modeling illuminator button (p. 66) Press to fire flash repeatedly to check the illumination and the shadows cast on the subject before taking pictures. Wireless remote flash cancel button (p. 75) The SB-800 will not fire, while this button is pressed.

18 Flash head rotating angle scale (p. 100)

19 Terminal cover

20 TTL multiple flash terminal (p. 92) Connects the SB-800 to the remote flash unit(s) in TTL multiple flash operation using cords.

21 Sync terminal (p. 93) Connects the SB-800 to the sync terminal of the remote flash unit(s) in other than TTL multiple flash operation using cords.

22 LCD panel (p. 119)

23 Control buttons (p. 12)

24 Ready-light Lights up when the SB-800 is fully recycled and ready to fire. Blinks after the SB-800 fires at its maximum output in various auto flash modes, indicating that the light may be insufficient.

25 Mounting foot lock lever (p. 22)

FLASH

READY

22

21

17

20

18

19

25

24

23

16

P re

pa ra

tio n

12

Control buttons

Recalling the underexposure value in the TTL auto flash mode Press the a and g buttons simultaneously to recall the underexposure value (p. 33). Resetting the settings Press the a and b buttons simultaneously for approx. 2 sec. to reset all settings, including the custom settings (except the distance unit selected in m/ft) to their default values. Button lock Press the b and g buttons simultaneously to lock the functions of the control buttons (except the b, Modeling illuminator, and FLASH buttons) to avoid accidental malfunction. Press the buttons again to release the lock.

e button/f button Press to increase or decrease the values of the highlighted items. b button Press for approx. 0.3 sec. to turn the power on and off. Multi Selector g button Press to select the items to be set. The selected

item is highlighted and can be changed using the e and f buttons.

Press for approx. 2 sec. to display the Custom settings mode (p. 68).

c button (wide)/d button (tele) Press to change the zoom-head position (p. 26).

FLASH button Press to test fire the flash (p. 20).

a button Press to set the flash mode (p. 30).

Control button quick reference Procedures for Custom settings, recalling the underexposure value in the TTL auto flash mode, resetting all settings to their default values, and the button lock are shown in the Control button quick reference chart on the back of the built-in bounce card.

13

Icons on the LCD panel

Auto Aperture flash In addition to Non-TTL auto A flash (see below), the SB-800s built-in sensor correctly controls the flash output in combination with data automatically transmitted from the camera and lens to the SB-800, including the ISO sensitivity, aperture, focal length, and exposure compensation value (p. 38).

Non-TTL auto flash The SB-800s built-in sensor measures the flash illumination reflected back from the subject, controlling the SB-800s light output automatically to give the correct exposure (p. 40).

Distance-priority manual flash Based on the ISO sensitivity value and aperture, the SB-800 controls the light output according to the distance value entered (p. 44).

Manual flash The flash always fires at a specified output in combination with the aperture and light output level (p. 46).

Repeating flash The SB-800 fires repeatedly during a single exposure, creating stroboscopic multiple- exposure effects (p. 48).

Icons on the LCD panel show the status of the operations set. These icons vary depending on the settings, the combination of camera/lens, and the exposure mode.

Icons with a single flash unit

Icons when a camera compatible with CLS* is used.

Monitor Preflashes Just before the flash fires, the SB-800 fires a series of imperceptible preflashes that are detected by the cameras TTL Multi-Sensor and analyzed for brightness and contrast (p. 36).

TTL mode Based on the exposure control information, the camera automatically controls the flash output level to give the correct exposure (p. 37).

Balanced Fill-Flash This always appears together with D. Based on the exposure control information, the flash output level is automatically controlled for a well-balanced exposure of the main subject and background (p.37).

Auto FP High-Speed Sync (CLS*) The SB-800 automatically fires at faster shutter speeds exceeding the cameras sync shutter speed (p. 60).

P re

pa ra

tio n

*CLS: Nikon Creative Lighting System (p. 5)

14

Icons on the LCD panel

Standby duration Represents the time before the standby function is activated (p. 67).

The wide-area AF-assist illuminator is activated

The wide-area AF-assist illuminator comes on (p. 62).

The wide-area AF-assist illuminator is canceled

The wide-area AF-assist illuminator does not come on (p. 62).

Flash firing canceled The SB-800 does not fire but the wide-area AF-assist illuminator still comes on (p. 62).

Control buttons being locked Control buttons (except the ON/OFF, Modeling illuminator and FLASH buttons) are locked (p. 12).

Red-eye reduction Red-eye reduction control is activated (p. 58).

LCD panel illuminator Pressing any control button turns on the LCD panel illuminator (p. 119).

Beyond the flash-shooting distance range The subject is beyond the flash shooting distance range. : the closest available distance, : the farthest available distance (p. 30).

Compatible with CLS (CLS*) The SB-800 is connected to cameras compatible with CLS* (p. 8).

Power zoom function The zoom-head position is automatically adjusted to match the lens focal length (p. 26).

Power zoom (auto) function

The zoom-head position is automatically adjusted to match the lens focal length when the SB-800 is used with COOLPIX cameras compatible with i-TTL (p. 26).

Manual zoom-head position setting You can adjust the zoom-head position manually (p. 26).

Canceling the power zoom function The power zoom is canceled, and the zoom-head position can only be adjusted manually (p. 26).

Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally The zoom-head position can be adjusted if the built-in wide-flash adapter is broken off accidentally (p. 117).

ISO sensitivity Represents the ISO sensitivity value (p. 24).

Flash output level compensation Represents the flash output level compensation value (p. 56).

Underexposure Indicates the underexposure value, showing that the light might be insufficient in the TTL auto flash mode (p. 33).

15

Highlighted items

Highlighted items indicate that they can be set or changed. The highlighted items return to normal after 8 seconds unless an adjustment is made.

*CLS: Nikon Creative Lighting System (p. 5)

Icons with multiple flash units

Icons in the Advanced Wireless Lighting mode

Master (CLS*) Represents the settings of the flash mode and flash output level compensation value of the master unit in the Advanced Wireless Lighting mode (p. 78).

Group A (B, C) (CLS*) Represents the settings of the flash mode and flash output level compensation value of the remote flash unit(s) in Group A (B, C) in the Advanced Wireless Lighting mode (p. 78).

Channel (CLS*) Represents the communication channel number through which the master and remote flash units exchange data in the Advanced Wireless Lighting mode (p. 78).

Wireless master In the wireless multiple flash mode, the SB-800 is used as the master flash unit connected to the camera (p. 72).

Wireless remote In the wireless multiple flash mode, the SB-800 is set as a remote flash unit, which fires in sync with the master flash unit (p. 72).

Wireless remote

In the wireless multiple flash mode, the SB-800 is set as a remote flash unit, which fires in sync with the master flash unit (p. 72).

Sound monitor on When the SB-800 is set as a remote flash unit, you can monitor its operation by listening to the beeping sound (p. 89).

Sound monitor canceled Beeping sound is off (p. 89).

(B,C)

P re

pa ra

tio n

16

Lenses

In this manual, Nikkor lenses are divided into two types: CPU Nikkor lenses and non-CPU Nikkor lenses.

CPU Nikkor lenses G-type Nikkor, D-type Nikkor, Non-G/D-type AF Nikkor (except for AF Nikkor for the F3AF), AI-P Nikkor

Non-CPU Nikkor lenses AI-S Nikkor, AI Nikkor, Series E, etc.

CPU lenses CPU lenses have CPU contacts.

G-type Nikkor lenses G-type Nikkor lenses send distance information to the camera body, but do not have an aperture ring. Therefore, set the aperture on the camera body. With some cameras, the usable exposure mode is limited. For more details, refer to the lens instruction manual.

D-type Nikkor lenses D-type Nikkor lenses send distance information to the camera body. Set the aperture either on the lens aperture ring or on the camera body. For more details, refer to the lens instruction manual.

Basic operation

In this section, basic procedures are illustrated so that you can easily perform flash photography in the TTL auto flash mode. You can easily perform flash photography by following Steps 18 on the left-hand pages.

In this section, basic procedures are described when a CPU lens is mounted on cameras compatible with CLS*, digital SLRs not compatible with CLS*, and cameras in Groups I to II. The SB-800s available functions and the LCD display vary depending on other camera/lens combinations.

*CLS: Nikon Creative Lighting System (p. 5)

18

1 Slide open the battery chamber lid in the direction of the arrow.

2 Install the batteries following the i and j marks as shown. Align the battery chamber lid attachment indexes, then close the battery chamber lid by sliding it into place while pressing down.

v Usable batteries Install four AA-type penlight batteries (1.5V or lower) of any of these types: (1) Alkaline-manganese (1.5V) (2) Lithium (1.5V) (3) Nickel (1.5V) (4) NiCd (rechargeable, 1.2V) (5) Ni-MH (Nickel Metal Hydride) (rechargeable, 1.2V)

When replacing batteries, replace all four (or five when using the Quick Recycling Battery Pack SD-800) with fresh ones of the same brand.

High-power manganese batteries are not recommended for use with the SB-800. Always carry extra batteries when traveling. For details on batteries, refer to Notes on batteries on page 115.

CAUTION! Do not use batteries not specified in this instruction manual, as this may

cause them to explode, leak corrosive liquids, or catch on fire. Do not mix battery brands or types, or use old with new batteries.

Otherwise the batteries may explode, leak corrosive liquids, or catch on fire. Do not recharge non-rechargeable batteries in a battery charger.

Otherwise the batteries may leak corrosive liquids or generate heat.

t Obtaining faster recycling times using 5 batteries Use the provided Quick Recycling Battery Pack SD-800 to install five batteries to shorten the recycling time. See page 64 for more details.

1 Installing the batteries

19

Minimum number of flashes and recycling times When using four (or five) fresh batteries of the same type and the Speedlight fires at M1/1 output.

Batteries Number of Min. recycling time Min. number of flashes/ batteries (approx.) recycling time

Alkaline- x4 6.0 sec. 130 / 6-30 sec. manganese x5 5.0 sec. 130 / 5-30 sec.

Lithium x4 7.5 sec. 170 / 7.5-30 sec.

x5 7.5 sec. 190 / 7.5-30 sec.

Nickel x4 6.0 sec. 140 / 6-30 sec.

x5 5.0 sec. 140 / 5-30 sec.

NiCd (1000 mAh) x4 4.0 sec. 90 / 4-30 sec. (rechargeable) x5 3.5 sec. 90 / 3.5-30 sec.

Ni-MH (2000 mA) x4 4.0 sec. 150 / 4-30 sec. (rechargeable) x5 2.9 sec. 150 / 2.9-30 sec.

Minimum recycling time is for operation using fresh batteries. This data was measured without using the wide-area AF-assist illuminator, zoom-head

position adjustment, or LCD panel illumination. The above data may vary due to variations in battery performance.

Replacing/recharging the batteries Refer to the following table to determine when to replace or recharge your batteries, if the ready-light takes a long time to come on.

Type of battery Recycling time Remedy

Alkaline-manganese More than 30 seconds

Lithium More than 10 seconds Replace

Nickel More than 10 seconds

Ni-Cd (rechargeable) More than 10 seconds Recharge

Ni-MH (rechargeable)

If extremely exhausted batteries are used, a strange sound can be heard caused by the flash head zooming back and forth even when the SB-800 is turned off. In this case, replace the SB-800s batteries even if an external battery source is used.

t External power sources Using an optional external power source increases the number of flash firings and provides faster recycling times (p. 113).

B as

ic o

pe ra

tio n

20

1 Press the b button for approx. 0.3 sec. to turn on the SB-800. Make sure the ready-light comes on.

2 Press the FLASH button to test fire the flash.

Test firing

CAUTION! When test firing the Speedlight, never position your eyes close to the flash head.

The SB-800 fires at specified output in the Manual flash mode, or at approx. 1/16 output in the Distance-priority manual or TTL auto flash mode.

In Auto Aperture/Non-TTL auto flash operations, the SB-800 fires at a flash output controlled by the ISO sensitivity, aperture, and zoom-head position.

In Auto Aperture/Non-TTL auto flash operations, you can check the amount of insufficient flash output by pressing the FLASH button before taking the actual picture (p. 52).

b button Pressing the b button for approx. 0.3 sec. turns the SB-800 on and the indications appear on the LCD panel. Pressing the button again turns the SB-800 off and the indications disappear.

2 Test firing (Confirming the exposure)

21

t Standby function to conserve battery power If the SB-800 and the camera are not used for more than a specified time, the standby function activates and automatically turns the SB-800 off to conserve battery power (it goes into the standby mode). In the standby mode, the R indicator appears on the LCD panel. When in the standby mode, the SB-800 turns back on again when the SB-800s b or

FLASH button is pressed, or the shutter release button is lightly pressed (when using a camera body that is compatible with TTL auto flash) (p. 8).

In the Wireless flash mode, the standby function activates in approx. 40 seconds (default setting) when the SB-800 is used as the master flash unit. However, the standby function does not work regardless of the SB-800s setting when the Speedlight is used as a remote flash unit (p. 73).

If the ready-light does not come on in approx. 60 seconds after turning the power on or after the flash has fired, the SB-800 enters the standby mode regardless of the SB-800s setting.

To avoid accidental firing or a malfunction when carrying the SB-800 in your camera bag, press the b button to turn the flash unit off and make sure the R indicator disappears.

Adjusting the time before the SB-800 goes into the standby mode Adjust this duration using Custom settings (p. 67).

B as

ic o

pe ra

tio n

22

1 Make sure the SB-800 and the camera body are turned off.

2 Rotate the mounting foot lock lever to the left, slide the SB-800s mounting foot into the cameras accessory shoe and turn the lock lever to the right.

3 Hold down the flash head tilting/rotating lock release button to adjust the flash head to the horizontal/front position.

v Turn the mounting foot lock lever securely until it stops To lock the Speedlight in place, turn the lock lever approx. 90 clockwise until it stops. To unlock, turn the lever counterclockwise until it stops.

Lock Unlock

FLASH

3 Attach the SB-800 to the camera and

23

adjust the flash head

t Warning indication If the flash head is not adjusted to the horizontal/front position, when the power is turned on, this warning appears on the LCD panel. See page 100 for the flash heads rotating angle.

A dotted line below the underbar appears when the flash head is tilted down 7.

The flash shooting distance range disappears if the flash head is adjusted to other than the horizontal/front or down 7 position.

B as

ic o

pe ra

tio n

24

In this manual, the sensitivity for digital SLRs and the film speed for film-based cameras are generally referred to as ISO sensitivity. For cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to II, and COOLPIX cameras compatible with i-TTL, the ISO sensitivity is automatically set and appears on the LCD panel when the camera and SB-800 are turned ON.

Available ISO sensitivity in TTL auto flash operation The SB-800s maximum ISO sensitivity range usable in the TTL auto flash mode is ISO 25 to 1000. The ISO sensitivity range may become narrower, depending on the cameras in use. For

details, see your camera instruction manual. The flash shooting distance range on the SB-800s LCD panel varies, depending on the

ISO sensitivity. Therefore, be sure to set the ISO sensitivity correctly.

u Digital data communication with the SB-800 When the SB-800 is used with cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to II, or COOLPIX cameras compatible with i-TTL, digital data communication is performed. The camera automatically sends the ISO sensitivity to the SB-800. With a CPU lens, the aperture and focal length are automatically set on the SB-800 (except for COOLPIX cameras compatible with i-TTL).

u Notes on setting the Speedlights ISO sensitivity In the TTL auto flash mode and Manual flash mode (except Distance-priority manual p flash), there is no direct connection between setting the ISO sensitivity on the Speedlight and controlling the flash output level. Setting the ISO sensitivity is for correctly displaying the flash shooting distance range or the shooting distance indication on the Speedlights LCD panel. In the Non-TTL auto flash mode (Auto Aperture flash B/Non-TTL auto flash A) and Distance-priority manual p flash operation, the correct exposure can be obtained by setting the cameras ISO sensitivity on the Speedlight, because the Speedlight controls the flash output. For cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to II and COOLPIX cameras compatible with i-TTL, the ISO sensitivity is automatically transferred from the camera to the Speedlight.

4 Setting the ISO sensitivity

25

Setting the ISO sensitivity for cameras in Groups III to VII For cameras in Groups III to VII, set the ISO sensitivity in the Custom settings mode (p. 67).

1 Turn the SB-800 off once, then turn it back on. After that, turn on the camera body.

2 Press the g button for approx. 2 sec. to display the Custom settings mode.

3 Press the e/f button and c/d button to select ISO, then press the g button.

4 Press the e or f button to highlight the preferred ISO sensitivity.

5 Press the g button for approx. 2 sec. or press the b button to return to the normal display.

B as

ic o

pe ra

tio n

1 The zoom-head position is indicated on the LCD panel. The zoom-head position is automatically

adjusted by the power zoom function or it can be manually adjusted.

The guide number indicating flash output level varies according to the zoom-head position (p. 43).

The power zoom function When the SB-800 is used with cameras compatible with CLS, digital SLRs not compatible with CLS, and cameras in Groups I to II in combination with a CPU lens, the power zoom function activates and the zoom head is automatically adjusted. The zoom-head position is automatically adjusted within the range of 24mm, 28mm,

35mm to 105mm in increments of 5mm between 35mm and 105mm when the power zoom function is activated.

When the lens focal length is not one of those indicated above, the zoom head adjusts to the closest wideangle setting of the lens in use. For example, if the zoom setting of a CPU lens is between 36mm and 39mm, the zoom-head position is adjusted to 35mm.

If a small M does not appear above the ZOOM indication on the LCD panel, the zoom- head position will be automatically adjusted. If a small M appears, press the c or d button several times until it disappears.

Power zoom activated Power zoom canceled

tWhen the SB-800 is used with COOLPIX cameras compatible with i-TTL

The zoom-head position is automatically adjusted by the power zoom function. AUTO appears along with ZOOM, but without a zoom-head position on the LCD panel.

26

5 Adjust the zoom-head position

27

Setting the zoom-head position manually When the SB-800 is used with cameras in Groups III to VII in combination with a non-CPU lens, or you want to change the zoom-head position to one that does not match the focal length, you should adjust the zoom-head position manually. Press the c button to move toward a wideangle setting and the d button to move

toward a telephoto setting. A small M above the ZOOM indication appears on the LCD panel while manually

setting the zoom-head position. When the camera/lens combination is compatible with the power zoom function, the

zoom-head position changes as follows, when a 35mm lens is attached:

M24mm M28mm 35mm M50mm M70mm M85mm M105mm

Generally, set the zoom-head position to the focal length of the lens in use or to the closest wideangle setting. For example, select the 50mm setting when using a 60mm lens.

t Canceling the power zoom function using Custom settings The power zoom function can be canceled in the Custom settings mode (p. 67). When the power zoom function is canceled, the zoom-head can be manually adjusted, but the zoom-head position indicator does not change even if the lens is zoomed, a lens is changed, or the b button is pressed. When the power zoom function is canceled, a small appears on the LCD panel. Press the c button to move toward a wideangle setting and the d button to move

toward a telephoto setting. The zoom-head position changes as follows:

24mm 28mm 35mm 50mm 70mm 85mm 105mm

t Using the built-in wide-flash adapter/Nikon Diffusion Dome Use the built-in wide-flash adapter when a 14mm to 23mm lens is mounted (p. 104). The power zoom function becomes inactive when using the wide-flash adapter. Press

the c or d button to adjust the zoom-head position to 14mm or 17mm. The zoom-head position is automatically set at 14mm when the Nikon Diffusion Dome is

attached (p. 101). Generally, when using a 14mm or 17mm lens, the distance between the camera and

subject differs much from the center of the frame to the periphery, so the peripheral area might not be sufficiently lit in some cases. The same is true when using the Nikon Diffusion Dome.

B as

ic o

pe ra

tio n

28

1 Set the cameras exposure mode to Programmed Auto (P). If Programmed Auto (P) cannot be set, select

another exposure mode. See the opposite page.

2 Set the cameras metering system to Matrix Metering Y. If Matrix Metering Y cannot be set, select

Center-Weighted Metering W.

t Exposure mode and metering system The cameras available exposure mode and metering system vary, depending on the cameras and lenses in use or the SB-800s flash modes. For details, refer to Detailed operation (p. 35), TTL auto flash modes available with the SB-800 (p. 108) and your cameras instruction manual. In the Programmed Auto (P) mode, the shutter speed is automatically set to the cameras

sync shutter speed, except in the Auto FP High-Speed sync mode (p. 60).

6 Setting the cameras exposure mode and

29

metering system

u Exposure modes other than Programmed Auto exposure (P) In Shutter-Priority Auto exposure (S) mode By selecting a slower shutter speed, the proper exposure for the background can be achieved. The camera selects the correct aperture. For details, see your cameras instruction

manual. However, set the shutter speed on the camera after confirming that the automatically controlled aperture will provide an appropriate shooting distance range for your subject. Refer to Flash shooting distance range in the TTL auto flash mode (p. 31).

If you set a shutter speed faster than the flash sync speed, the camera automatically shifts to its fastest sync speed when the SB-800 is turned on (except in the Auto FP High-Speed sync mode) (p. 60).

In Aperture-Priority Auto exposure (A) mode By selecting the aperture, you can control depth of field and the flash shooting distance range. The camera selects the correct shutter speed. For details, see your cameras instruction

manual. To determine the aperture, refer to the Guide number (p. 43) and Flash shooting

distance range in the TTL auto flash modes (p. 31).

In Manual exposure (M) mode By selecting the shutter speed and aperture, you can control the exposure of the background, the depth of field, and the flash shooting distance range. If you set a shutter speed faster than the flash sync speed, the camera automatically

shifts to its fastest sync speed when the SB-800 is turned on. This is true of all cameras, except mechanical shutter cameras and when using the Auto FP High-Speed sync mode (p. 60).

To determine the aperture, refer to Guide number (p. 43) and Flash shooting distance range in the TTL auto flash mode (p. 31).

B as

ic o

pe ra

tio n

30

7 Setting the SB-800s flash mode

1 Press the a button to set the flash mode. Display Do on the LCD panel.

2 Confirm that the main subject is within the flash shooting distance range.

Selecting the flash mode Every time you press the a button, the available flash mode icon changes. Refer to Icons on the LCD panel (p. 13).

Do D B p G q

A

Note that the usable flash modes only appear and vary, and the unavailable flash modes will be skipped and do not appear, when pressing the a button.

The SB-800s available flash modes vary, depending on the cameras and lenses in use or the cameras exposure mode and metering system. Refer to Detailed operation (p. 35), TTL auto flash modes available with the SB-800 (p. 108) and your cameras instruction manual.

31

About the flash shooting distance range The SB-800s flash shooting distance range is 0.6m to 20m (2 to 66 ft.) and varies, depending on the ISO sensitivity, zoom-head position, and lens aperture in use.

Flash shooting distance range in the TTL auto flash mode

*1 With the Nikon Diffusion Dome attached and the wide-flash adapter in place *2 With the Nikon Diffusion Dome attached *3 With the wide-flash adapter in place *4 TTL auto flash operation is not possible at this ISO sensitivity. For ISO 1000, use an

aperture 2/3 of an f/stop smaller than the aperture for ISO 1600, or 1/3 larger than the aperture for ISO 800.

*5 Programmed TTL Auto Flash with the F-501/N2020, F-401s/N4004s, F-401/N4004, and F-301/N2000. (ISO 25 to ISO 400 for the F-401s and F-401/N4004)

B as

ic o

pe ra

tio n

A pe

rt ur

e

Fl as

h sh

oo tin

g di

st an

ce ra

ng e

(m /ft

.)

ISO sensitivity Zoom-head position (mm)

1600 800 400 200 100 50 25 1 2 14 17 24 28 35 50 70 85 105

4

2.8 2 1.4

4 2.8 2 1.4

5.6 4 2.8 2 1.4

8 5.6 4 2.8 2 1.4

11 8 5.6 4 2.8 2 1.4

16 11 8 5.6 4 2.8 2

22 16 11 8 5.6 4 2.8

32 22 16 11 8 5.6 4

32 22 16 11 8 5.6

32 22 16 11 8

32 22 16 11

32 22 16

0.8-9.0/ 1.0-11/ 1.1-12/ 1.3-14/ 1.9-20/ 2.0-20/ 2.4-20/ 2.8-20/ 3.0-20/ 3.4-20/ 3.6-20/ 2.6-29 3.3-37 3.7-41 4.1-46 6.2-66 6.6-66 7.8-66 9.3-66 10-66 11-66 12-66

0.6-6.3/ 0.7-8.0/ 0.8-9.0/ 0.8-10/ 1.3-15/ 1.4-16/ 1.7-19/ 2.0-20/ 2.2-20/ 2.4-20/ 2.5-20/ 2.0-21 2.3-26 2.6-29 2.6-33 4.3-49 4.6-52 5.5-62 6.6-66 7.4-66 7.8-66 8.3-66

0.6-4.5/ 0.6-5.7/ 0.6-6.3/ 0.7-7.0/ 1.0-10/ 1.0-11/ 1.2-13/ 1.4-16/ 1.6-18/ 1.7-19/ 1.8-20/ 2.0-15 2.0-19 2.0-20 2.0-23 3.1-35 3.3-37 3.9-44 4.6-52 5.2-59 5.5-62 5.8-66

0.6-3.2/ 0.6-4.0/ 0.6-4.5/ 0.6-5.0/ 0.7-7.5/ 0.7-8.0/ 0.8-9.5/ 1.0-11/ 1.1-13/ 1.2-13/ 1.3-14/ 2.0-10 2.0-13 2.0-14 2.0-16 2.2-25 2.3-26 2.8-31 3.3-37 3.7-42 3.9-44 4.1-47

0.6-2.2/ 0.6-2.8/ 0.6-3.1/ 0.6-3.5/ 0.6-5.3/ 0.6-5.7/ 0.6-6.7/ 0.7-7.6/ 0.8-9.0/ 0.8-9.5/ 0.9-10/ 2.0-7.4 2.0-9.3 2.0-10 2.0-11 2.0-17 2.0-19 2.0-22 2.3-26 2.6-29 2.8-31 2.9-33 0.6-1.6/ 0.6-2.0/ 0.6-2.2/ 0.6-2.5/ 0.6-3.7/ 0.6-4.0/ 0.6-4.8/ 0.6-5.3/ 0.6-6.3/ 0.6-6.7/ 0.6-7.1/ 2.0-5.2 2.0-6.6 2.0-7.3 2.0-8.2 2.0-12 2.0-13 2.0-16 2.0-19 2.0-21 2.0-22 2.1-23 0.6-1.1/ 0.6-1.4/ 0.6-1.6/ 0.6-1.8/ 0.6-2.6/ 0.6-2.8/ 0.6-3.4/ 0.6-4.0/ 0.6-4.5/ 0.6-4.8/ 0.6-5.0/ 2.0-3.7 2.0-4.6 2.0-5.2 2.0-5.8 2.0-8.7 2.0-9.3 2.0-11 2.0-13 2.0-15 2.0-16 2.0-17 0.6-0.8/ 0.6-1.0/ 0.6-1.1/ 0.6-1.2/ 0.6-1.8/ 0.6-2.0/ 0.6-2.4/ 0.6-2.8/ 0.6-3.2/ 0.6-3.4/ 0.6-3.6/ 2.0-2.6 2.0-3.3 2.0-3.7 2.0-4.1 2.0-6.2 2.0-6.6 2.0-7.8 2.0-9.3 2.0-10 2.0-11 2.0-12

_ 0.6-0.7/ 0.6-0.7/ 0.6-0.8/ 0.6-1.3/ 0.6-1.4/ 0.6-1.7/ 0.6-2.0/ 0.6-2.2/ 0.6-2.4/ 0.6-2.5/ 2.0-2.3 2.0-2.6 2.0-2.9 2.0-4.4 2.0-4.6 2.0-5.5 2.0-6.6 2.0-7.4 2.0-7.8 2.0-8.3

_ _ _ _ 0.6-0.9/ 0.6-1.0/ 0.6-1.2/ 0.6-1.4/ 0.6-1.6/ 0.6-1.7/ 0.6-1.8/ 2.0-3.1 2.0-3.3 2.0-3.9 2.0-4.6 2.0-5.2 2.0-5.5 2.0-5.8

5

3 3

32

1 Confirm the cameras sync mode. For normal flash photography, use the

cameras Front-curtain sync mode.

2 Compose the picture, confirm that the ready-light on the SB-800 or in the cameras viewfinder is on, then shoot.

v Set the cameras flash sync mode to Front-curtain sync. With cameras featuring a Rear-curtain sync flash mode, make sure the cameras flash sync mode is set to Front-curtain sync. For other flash sync modes, refer to Slow-sync flash (p. 58), Red-eye reduction

with slow-sync flash mode (p. 58), or Rear-curtain sync (p. 59). Refer to the cameras instruction manual for details on the flash sync mode.

8 Compose the picture and shoot with flash

33

v If the ready-light blinks after shooting, the light might be insufficient for correct exposure.

In the TTL auto and Non-TTL auto flash modes, when the flash has fired at its maximum output and underexposure may have occurred, the ready-lights on the SB-800 and in the cameras viewfinder blink for approx. 3 sec. Depending on the camera in use, the ready-light on the SB-800 or in the cameras viewfinder lights up. To compensate, use a wider aperture or move closer to the subject and reshoot.

Display of the amount of underexposure For cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Group I and COOLPIX cameras compatible with i-TTL in the TTL auto flash mode, the amount of underexposure (0 to 3.0 EV) appears for approx. 3 sec on the SB-800s LCD panel; at the same time the above ready- lights blink. Pressing the a and g buttons simultaneously recalls this display.

B as

ic o

pe ra

tio n

34

For COOLPIX cameras, such as the COOLPIX 8800 and 4500, having an accessory shoe (hot-shoe) or TTL multiple flash terminal: When more powerful illumination is required or when performing multiple flash, it is recommended to connect the SB-800 or another Nikon Speedlight compatible with TTL auto flash to the COOLPIX. Auto flash operation is possible by setting the SB-800s flash mode to TTL auto flash. The flash output level is controlled by detecting signals from the camera to determine when to start and stop firing. This is controlled by Standard i-TTL flash operation with COOLPIX cameras compatible with i-TTL and by Non-TTL operation with other COOLPIX cameras. For connection to COOLPIX cameras featuring hot shoe contacts

such as the COOLPIX 8800, attach the Speedlight directly to the accessory shoe.

Optional accessories such as the Multi-Flash Bracket Unit SK-E900 should be used for connection with COOLPIX cameras having a TTL multiple flash terminal but no hot-shoe contacts.

For details, see your cameras instruction manual.

Please note that wireless multiple flash using the COOLPIXs built-in flash as a master flash unit and the SB-800 as a remote flash unit cannot be performed.

Using the SB-800 with the COOLPIX

Detailed operation

This section provides a variety of flash modes available with the SB-800. Be sure to refer to your cameras instruction manual for specific information on camera settings and functions.

36

SB-800s available flash modes

The SB-800s available flash modes vary, depending on the cameras and lenses in use or the cameras exposure mode. Using the TTL auto flash mode is recommended for normal flash photography.

Available flash modes (Indicators, usable cameras) TTL auto flash mode i-TTL mode: Do/D: Cameras compatible with CLS,

COOLPIX cameras compatible with i-TTL

D-TTL mode: Do/D: Digital SLRs not compatible with CLS TTL (film based) mode: Do/D: Cameras in Groups I to VI (No o

appears with cameras in Groups III and IV while performing Balanced Fill-Flash)

Non-TTL auto flash mode Auto Aperture flash: B (p. 38): Cameras compatible with CLS, digital

SLRs not compatible with CLS, cameras in Groups I to II and COOLPIX cameras compatible with i-TTL

Non-TTL auto flash: A (p. 40): No limitation

Manual mode Distance-priority

manual flash: p (p. 44): Except D1X and D1H digital cameras. Manual flash: G (p. 46): No limitation Repeating flash: q (p. 48): Except COOLPIX cameras compatible

with i-TTL

u Monitor Preflashes The SB-800 fires a series of imperceptible Monitor Preflashes just before the flash fires to obtain information on the subject in these cases: (1) when the SB-800 is used with cameras compatible with CLS, digital SLRs

not compatible with CLS, cameras in Group I with a CPU lens, and COOLPIX cameras compatible with i-TTL, and flash mode is set to TTL auto flash, and

(2) when the SB-800 is used with cameras compatible with CLS with a CPU lens, and the flash mode is set to Auto Aperture flash.

Monitor Preflashes are fired instantaneously and cannot be differentiated from the main flash, but H appears on the LCD panel (using a single flash unit). However, for cameras in Group I, Monitor Preflashes are not fired when the SB-800s flash head is adjusted to other than the horizontal/front or down to 7 position, or the cameras flash sync mode is set to Rear-curtain sync, even when H appears on the LCD panel.

D et

ai le

d op

er at

io n

37

TTL auto flash mode

TTL auto flash: D In this mode, the flash illumination that is reflected back from the subject is detected by the cameras TTL auto flash sensor and the camera automatically controls the flash output level to give the correct exposure.

Automatic Balanced Fill-Flash: Do Press the a button to display Do on the LCD panel, and Automatic Balanced Fill-Flash is performed. The flash output level is automatically adjusted for a well-balanced exposure of the main subject and background. (While performing Balanced Fill-Flash, no o appears with cameras in Groups III and IV.) Do indicates i-TTL Automatic Balanced Fill-Flash in the i-TTL mode.

Standard TTL flash: D Press the a button to display D on the LCD panel, and Standard TTL flash is performed. The main subject is correctly exposed regardless of the background brightness. This is useful when you want to highlight the main subject. D indicates Standard i-TTL flash in the i-TTL mode, Standard TTL flash for Digital

SLRs in the D-TTL mode, and Standard TTL flash in the TTL (film-based) mode.

t Notes on TTL mode indicators Comparison tables are provided on pages 108-110 to show the SB-800s TTL mode indicators and the corresponding ones used in the instruction manuals of Speedlights featuring no CLS. For details on shooting procedures in the TTL auto flash mode, refer to Basic operation

(p. 17).

t Flash shooting in the 1/300 TTL High-Speed Flash sync mode (F5 only)

The farthest flash shooting distance cannot be read on the SB-800s LCD panel. In this case, use the guide number table and equation (p. 106) for calculating this distance, according to each zoom-head position.

u Difference in flash control level in TTL and Non-TTL auto flash mode

In either flash mode, the flash illumination that is reflected back from the subject is measured to control the flash output level. In the TTL mode, this measurement is made through-the-lens, while in the Non-TTL auto flash mode, it is performed through the Speedlights light sensor window for Non-TTL auto flash covering a limited range. Therefore, if you take the same subject in different flash modes, some difference in the flash control level might appear, depending on shooting conditions. Use of the TTL mode is recommended when taking pictures with cameras compatible with TTL auto flash.

38

Non-TTL auto flash mode

Auto Aperture B flash The SB-800s built-in sensor measures the flash illumination reflected from the subject and controls the flash output in combination with data automatically transmitted from the camera and lens to the SB-800, including the ISO sensitivity value and exposure compensation value as well as the aperture and focal length of the lens. Auto Aperture flash is available with cameras compatible with CLS, digital SLRs not

compatible with CLS, cameras in Groups I and II when used with a CPU lens, and COOLPIX cameras compatible with i-TTL.

Auto Aperture flash is automatically set (default setting) for the above camera/lens combinations. To cancel Auto Aperture flash and set to Non-TTL auto flash (p. 40), use Custom settings (p. 67).

1 Set the cameras exposure mode to Programmed Auto (P) or Aperture-Priority Auto (A). If FEE appears on the cameras LCD panel while

the cameras exposure mode is set to Programmed Auto (P), reset the exposure mode to Aperture-Priority Auto (A).

2 Lock the CPU lens aperture at its minimum. Not necessary with a G-type lens.

3 Press the a button to display B on the LCD panel.

4 While looking at the flash shooting distance range on the SB-800s LCD panel, set the aperture on the camera when the cameras exposure mode is set to A. Making exposure compensation on the SB-800 is also

possible (p. 56).

D et

ai le

d op

er at

io n

39

5 Compose the picture, confirm that the ready-light is on, then shoot. When the flash has fired at its maximum output and

underexposure may have occurred, the ready-light on the SB-800 blinks for approx. 3 sec. To compensate, use a wider aperture or move closer to the subject and reshoot.

Setting the aperture in Auto Aperture B flash operation Set the aperture on the camera or lens within the available range as shown in the table below. Usable flash shooting distance ranges in Auto Aperture flash operation

*1 With the Nikon Diffusion Dome attached and the wide-flash adapter in place *2 With the Nikon Diffusion Dome attached *3 With the wide-flash adapter in place

For example, for an ISO sensitivity of 100, with the zoom-head position adjusted to 35mm, and the subject at a distance of 5m (16.4 ft.), selecting an aperture of f/2 to f/5.6 from the table gives the correct exposure.

u Notes on using a telephoto lens in the Non-TTL auto flash mode When you shoot a distant subject using a telephoto lens in Auto Aperture B or Non-TTL auto A flash operation, underexposure may occur even though the subject is within the usable flash shooting distance range. Use of the TTL mode is recommended when taking pictures with cameras compatible with TTL auto flash.

A pe

rt ur

e

Fl as

h sh

oo tin

g di

st an

ce ra

ng e

(m /ft

.)

ISO sensitivity Zoom-head position (mm)

1600 800 400 200 100 50 25 1 2 14 17 24 28 35 50 70 85 105

8 5.6 4 2.8 2 1.4

11 8 5.6 4 2.8 2 1.4

16 11 8 5.6 4 2.8 2

22 16 11 8 5.6 4 2.8

32 22 16 11 8 5.6 4

32 22 16 11 8 5.6

32 22 16 11 8

32 22 16 11

32 22 16

0.6-6.3/ 0.7-8.0/ 0.8-9.0/ 0.8-10/ 1.3-15/ 1.4-16/ 1.7-19/ 2.0-20/ 2.2-20/ 2.4-20/ 2.5-20/ 2.0-21 2.3-26 2.6-29 2.6-33 4.3-49 4.6-52 5.5-62 6.6-66 7.4-66 7.8-66 8.3-66

0.6-4.5/ 0.6-5.7/ 0.6-6.3/ 0.7-7.0/ 1.0-10/ 1.0-11/ 1.2-13/ 1.4-16/ 1.6-18/ 1.7-19/ 1.8-20/ 2.0-15 2.0-19 2.0-20 2.0-23 3.1-35 3.3-37 3.9-44 4.6-52 5.2-59 5.5-62 5.8-66

0.6-3.2/ 0.6-4.0/ 0.6-4.5/ 0.6-5.0/ 0.7-7.5/ 0.7-8.0/ 0.8-9.5/ 1.0-11/ 1.1-13/ 1.2-13/ 1.3-14/ 2.0-10 2.0-13 2.0-14 2.0-16 2.2-25 2.3-26 2.8-31 3.3-37 3.7-42 3.9-44 4.1-47

0.6-2.2/ 0.6-2.8/ 0.6-3.1/ 0.6-3.5/ 0.6-5.3/ 0.6-5.7/ 0.6-6.7/ 0.7-7.6/ 0.8-9.0/ 0.8-9.5/ 0.9-10/ 2.0-7.4 2.0-9.3 2.0-10 2.0-11 2.0-17 2.0-19 2.0-22 2.3-26 2.6-29 2.8-31 2.9-33 0.6-1.6/ 0.6-2.0/ 0.6-2.2/ 0.6-2.5/ 0.6-3.7/ 0.6-4.0/ 0.6-4.8/ 0.6-5.3/ 0.6-6.3/ 0.6-6.7/ 0.6-7.1/ 2.0-5.2 2.0-6.6 2.0-7.3 2.0-8.2 2.0-12 2.0-13 2.0-16 2.0-19 2.0-21 2.0-22 2.1-23 0.6-1.1/ 0.6-1.4/ 0.6-1.6/ 0.6-1.8/ 0.6-2.6/ 0.6-2.8/ 0.6-3.4/ 0.6-4.0/ 0.6-4.5/ 0.6-4.8/ 0.6-5.0/ 2.0-3.7 2.0-4.6 2.0-5.2 2.0-5.8 2.0-8.7 2.0-9.3 2.0-11 2.0-13 2.0-15 2.0-16 2.0-17 0.6-0.8/ 0.6-1.0/ 0.6-1.1/ 0.6-1.2/ 0.6-1.8/ 0.6-2.0/ 0.6-2.4/ 0.6-2.8/ 0.6-3.2/ 0.6-3.4/ 0.6-3.6/ 2.0-2.6 2.0-3.3 2.0-3.7 2.0-4.1 2.0-6.2 2.0-6.6 2.0-7.8 2.0-9.3 2.0-10 2.0-11 2.0-12

_ 0.6-0.7/ 0.6-0.7/ 0.6-0.8/ 0.6-1.3/ 0.6-1.4/ 0.6-1.7/ 0.6-2.0/ 0.6-2.2/ 0.6-2.4/ 0.6-2.5/ 2.0-2.3 2.0-2.6 2.0-2.9 2.0-4.4 2.0-4.6 2.0-5.5 2.0-6.6 2.0-7.4 2.0-7.8 2.0-8.3

_ _ _ _ 0.6-0.9/ 0.6-1.0/ 0.6-1.2/ 0.6-1.4/ 0.6-1.6/ 0.6-1.7/ 0.6-1.8/ 2.0-3.1 2.0-3.3 2.0-3.9 2.0-4.6 2.0-5.2 2.0-5.5 2.0-5.8

3 3

40

Non-TTL auto flash mode

Non-TTL auto A flash The SB-800s built-in sensor measures the flash illumination reflected from the subject, automatically controlling the SB-800s light output to give the correct exposure. This allows you to make exposure compensation (p. 54) easily by varying the aperture set on the camera or lens. No limitation on usable cameras. Auto Aperture flash (p. 38) is automatically set (default setting) when the SB-800 is used

with cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I and II in combination with a CPU lens, and COOLPIX cameras compatible with i-TTL. To cancel Auto Aperture flash and set to Non-TTL auto flash, use Custom settings (p. 67).

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Press the a button to display A on the LCD panel.

3 Press the e or f button to change the aperture, bringing the subject within the flash shooting distance range.

4 Set the aperture that appears on the SB-800s LCD panel on the lens or camera.

D et

ai le

d op

er at

io n

41

5 Set the camera to its highest flash sync shutter speed. For details, see your cameras instruction manual.

6 Compose the picture, make sure the ready-light is on, then shoot. When the flash has fired at its maximum output and

underexposure may have occurred, the ready-light on the SB-800 blinks for approx. 3 sec. To compensate, use a wider aperture or move closer to the subject and reshoot.

Setting the aperture in Non-TTL auto A flash operation Set the aperture within the available range as shown in the table below.

Usable flash shooting distance ranges in Non-TTL auto flash operation

*1 With the Nikon Diffusion Dome attached and the wide-flash adapter in place *2 With the Nikon Diffusion Dome attached *3 With the wide-flash adapter in place

For example, for an ISO sensitivity of 100, with the zoom-head position adjusted to 35mm, and the subject at a distance of 5m (16.4 ft.), selecting apertures from f/2 to f/5.6 from the table will give the correct exposure.

To set the aperture on Zoom-Nikkor lenses having variable maximum apertures, refer to The flash shooting distance range with zoom lenses having a variable aperture (p. 57).

A pe

rt ur

e

Fl as

h sh

oo tin

g di

st an

ce ra

ng e

(m /ft

.)

ISO sensitivity Zoom-head position (mm)

1600 800 400 200 100 50 25 1 2 14 17 24 28 35 50 70 85 105

8 5.6 4 2.8 2 1.4

11 8 5.6 4 2.8 2 1.4

16 11 8 5.6 4 2.8 2

22 16 11 8 5.6 4 2.8

32 22 16 11 8 5.6 4

32 22 16 11 8 5.6

32 22 16 11 8

32 22 16 11

32 22 16

0.6-6.3/ 0.7-8.0/ 0.8-9.0/ 0.8-10/ 1.3-15/ 1.4-16/ 1.7-19/ 2.0-20/ 2.2-20/ 2.4-20/ 2.5-20/ 2.0-21 2.3-26 2.6-29 2.6-33 4.3-49 4.6-52 5.5-62 6.6-66 7.4-66 7.8-66 8.3-66

0.6-4.5/ 0.6-5.7/ 0.6-6.3/ 0.7-7.0/ 1.0-10/ 1.0-11/ 1.2-13/ 1.4-16/ 1.6-18/ 1.7-19/ 1.8-20/ 2.0-15 2.0-19 2.0-20 2.0-23 3.1-35 3.3-37 3.9-44 4.6-52 5.2-59 5.5-62 5.8-66

0.6-3.2/ 0.6-4.0/ 0.6-4.5/ 0.6-5.0/ 0.7-7.5/ 0.7-8.0/ 0.8-9.5/ 1.0-11/ 1.1-13/ 1.2-13/ 1.3-14/ 2.0-10 2.0-13 2.0-14 2.0-16 2.2-25 2.3-26 2.8-31 3.3-37 3.7-42 3.9-44 4.1-47

0.6-2.2/ 0.6-2.8/ 0.6-3.1/ 0.6-3.5/ 0.6-5.3/ 0.6-5.7/ 0.6-6.7/ 0.7-7.6/ 0.8-9.0/ 0.8-9.5/ 0.9-10/ 2.0-7.4 2.0-9.3 2.0-10 2.0-11 2.0-17 2.0-19 2.0-22 2.3-26 2.6-29 2.8-31 2.9-33 0.6-1.6/ 0.6-2.0/ 0.6-2.2/ 0.6-2.5/ 0.6-3.7/ 0.6-4.0/ 0.6-4.8/ 0.6-5.3/ 0.6-6.3/ 0.6-6.7/ 0.6-7.1/ 2.0-5.2 2.0-6.6 2.0-7.3 2.0-8.2 2.0-12 2.0-13 2.0-16 2.0-19 2.0-21 2.0-22 2.1-23 0.6-1.1/ 0.6-1.4/ 0.6-1.6/ 0.6-1.8/ 0.6-2.6/ 0.6-2.8/ 0.6-3.4/ 0.6-4.0/ 0.6-4.5/ 0.6-4.8/ 0.6-5.0/ 2.0-3.7 2.0-4.6 2.0-5.2 2.0-5.8 2.0-8.7 2.0-9.3 2.0-11 2.0-13 2.0-15 2.0-16 2.0-17 0.6-0.8/ 0.6-1.0/ 0.6-1.1/ 0.6-1.2/ 0.6-1.8/ 0.6-2.0/ 0.6-2.4/ 0.6-2.8/ 0.6-3.2/ 0.6-3.4/ 0.6-3.6/ 2.0-2.6 2.0-3.3 2.0-3.7 2.0-4.1 2.0-6.2 2.0-6.6 2.0-7.8 2.0-9.3 2.0-10 2.0-11 2.0-12

_ 0.6-0.7/ 0.6-0.7/ 0.6-0.8/ 0.6-1.3/ 0.6-1.4/ 0.6-1.7/ 0.6-2.0/ 0.6-2.2/ 0.6-2.4/ 0.6-2.5/ 2.0-2.3 2.0-2.6 2.0-2.9 2.0-4.4 2.0-4.6 2.0-5.5 2.0-6.6 2.0-7.4 2.0-7.8 2.0-8.3

_ _ _ _ 0.6-0.9/ 0.6-1.0/ 0.6-1.2/ 0.6-1.4/ 0.6-1.6/ 0.6-1.7/ 0.6-1.8/ 2.0-3.1 2.0-3.3 2.0-3.9 2.0-4.6 2.0-5.2 2.0-5.5 2.0-5.8

3 3

42

Manual mode

Manual mode The SB-800 features three manual modes.

Distance-priority manual flash p

Manual flash G

Repeating flash q

You can calculate the correct aperture by using the guide number table and the shooting distance. Then set the same aperture manually on the lens. In this case, set the cameras exposure mode to Aperture-Priority Auto (A) or Manual (M). Refer to your cameras instruction manual for details on camera and lens aperture

settings. With the SB-800 in the Manual mode, if the cameras exposure mode is set to other than

Aperture-Priority (A) or Manual (M), the shutter may not be released, depending on the cameras in use. For details, refer to your cameras instruction manual.

In the Manual mode, no warning ready-light blinks to indicate that the light may have been insufficient for correct exposure after shooting.

Determining the aperture, flash output level and shooting distance in the Manual mode

In the Manual mode, use the guide number table and the following equation to calculate the aperture, flash output level, and shooting distance to obtain the correct exposure. The guide number (GN at ISO 100; m/ft) indicates the amount of light generated by

the flash. The larger the number, the greater the flash output.

Guide number (ISO 100, m/ft)

*1 With the Nikon Diffusion Dome attached and the wide-flash adapter in place *2 With the Nikon Diffusion Dome attached *3 With the wide-flash adapter in place

Zoom-head position (mm)

1 2 143 173 24 28 35 50 70 85 105

M1/1 12.5/41 16/52 17/56 19/62 30/98 32/105 38/125 44/144 50/164 53/174 56/184

M1/2 8.8/29 11.3/37 12/39 13.4/44 21.2/70 22.6/74 26.9/88 31/102 35.4/116 37.5/123 40/131

M1/4 6.3/21 8.0/26 8.5/28 9.5/31 15.0/49 16/52 19/62 22/72 25/82 26.5/87 28/92

M1/8 4.4/14 5.7/19 6.0/20 6.7/22 10.6/35 11.3/37 13.4/44 15.6/51 17.7/58 18.7/61 19.8/65

M1/16 3.1/10 4.0/13 4.3/14 4.8/16 7.5/25 8.0/26 9.5/31 11/36 12.5/41 13.3/44 14/46

M1/32 2.2/7 2.8/9 3.0/10 3.4/11 5.3/17 6.0/20 6.7/22 7.8/26 8.8/29 9.4/31 9.9/32

M1/64 1.6/5 2.0/7 2.1/7 2.4/8 3.7/12 4.0/13 4.8/16 5.5/18 6.3/21 6.6/22 7.0/23

M1/128 1.1/4 1.4/5 1.5/5 1.7/6 2.6/8.5 2.8/9 3.4/11 3.9/13 4.4/14 4.7/15 4.9/16

Flash output level

43

ISO sensitivity factors For sensitivities other than ISO 100, multiply the guide number by the factors shown in the table below.

To calculate the correct aperture Calculate the correct aperture by using this equation and the guide number table, according to the ISO sensitivity, shooting distance, flash output level and zoom-head position that are set:

f/stop (aperture) = Guide number (GN at ISO 100; m/ft.) x ISO sensitivity factor Shooting distance (m/ft)

For example, for the ISO sensitivity of 400 (or ISO sensitivity factor: 2), with the zoom-head position adjusted to 28mm, and the flash output level set to M1/1: Referring to the guide number table, determine the guide number as 32/105 (m/ft.).

When the shooting distance is 4m (13.1 ft.), the correct aperture value is: 32/105 (GN at ISO 100, m/ft) x 2 (ISO sensitivity factor for ISO 400) 4/13.1 (shooting distance; m/ft.) = 16 (aperture)

Set the aperture value 16 on both the SB-800 and the camera or lens.

To obtain the correct flash output level Calculate the guide number (GN at ISO 100; m/ft.) by using this equation, according to the shooting distance and aperture required.

Guide number (GN at ISO 100; m/ft.) = Shooting distance (m/ft) x Aperture (f/) ISO sensitivity factor

Referring to the guide number table, determine an appropriate flash output level corresponding to the guide number obtained above, then set the same value on the SB-800. For example, for the ISO sensitivity of 400 (or ISO sensitivity factor: 2) and the shooting distance of 4m (13.1 ft) with an aperture of f/8:

4/13.1 (shooting distance; m/ft.) x 8 (aperture value) 2 (ISO sensitivity factor of ISO 400) = 16/52 (GN at ISO 100; m/ft.)

When the zoom-head position is adjusted to 28mm, set M1/4 flash output level on the SB-800, which can be obtained from GN 16/52 (m/ft.) corresponding to the zoom-head position of 28mm referring to the guide number table.

In Distance-priority manual flash operation, the correct flash output level is automatically determined by the SB-800 according to the shooting distance, aperture and ISO sensitivity that are set.

To calculate the shooting distance Calculate the shooting distance (m/ft.) by using this equation and the guide number table, according to the ISO sensitivity, aperture value, flash output level and zoom-head position that are set:

Shooting distance (m/ft.) = Guide number (GN at ISO 100; m/ft.) x ISO sensitivity factor Aperture (f/)

D et

ai le

d op

er at

io nISO 25 50 100 200 400 800 1600

Factors x0.5 x0.71 x1 x1.4 x2 x2.8 x4

44

Manual mode

Distance-priority manual p flash In this flash operation, the SB-800 automatically controls the light output according to the distance value and aperture set. Enter the distance value and you can take pictures having the same exposure even when shooting at different apertures. Distance-priority manual flash p is not possible with D1X and D1H digital cameras. This mode allows you to make exposure compensation by varying the flash output level

compensation value (p. 56).

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Press the a button to display p on the LCD panel.

3 Press the g button to highlight the distance display, then press the e or f button to increase or decrease the distance values. The usable distance range is 0.3m to 20m (1 to

65.6 ft.) and varies depending on the ISO sensitivity.

4 Set the aperture. For cameras compatible with CLS, digital SLRs not

compatible with CLS, cameras in Groups I and II with CPU lenses, and COOLPIX cameras compatible with i-TTL, set the SB-800s aperture on the camera. You cannot set the aperture on the SB-800 directly.

For other camera/lens combinations, press the g button to highlight the aperture display, then press the e or f button to increase or decrease the aperture value.

45

5 Set the aperture that appears on the SB-800s LCD panel on the lens or camera. With cameras in Groups III to VII.

6 Confirm that the ready-light is on, then shoot.

Distance values that can be entered when performing Distance-priority manual p flash operation (m/ft.)

0.3/1 0.4/1.3 0.5/1.6 0.6/2 0.7/2.3 0.8/2.6 0.9/3 1.0/3.3 1.3/4.3 1.4/4.6

1.6/5.2 1.8/5.9 2.0/6.6 2.2/7.2 2.5/8.2 2.8/9.2 3.1/10.2 3.5/11.5 4.0/13.1 4.5/14.8

5.0/16.4 5.6/18.4 6.3/20.7 7.1/23.3 8.0/26.2 9.0/29.6 10/32.8 11/36.0 13/42.7 14/45.9

16/52.5 18/59.1 20/65.6

Choose an appropriate flash shooting distance from the table above. If a desirable distance value is not found in the table, use a shorter distance. For example, if the desired shooting distance is 2.7m (8.9 ft.), set 2.5m (8.2 ft.) on the LCD panel.

t Beyond the flash-shooting distance range warning In distance-priority manual flash operation, the distance exceeding the available flash shooting distance range cannot be displayed on the LCD panel. Therefore, if the available distance range is shifted by changing the ISO sensitivity, aperture, or zoom-head position after you have set the shooting distance and aperture, the farthest (or closest) available flash shooting distance value is highlighted with an arrow pointing toward the available flash shooting distance range.

The figure shows that the farthest available flash shooting distance is 2.5m (8.2 ft.).

D et

ai le

d op

er at

io n

46

Manual mode

Manual G flash In Manual flash photography, you select the aperture and flash output level. In this way, you can control the exposure and flash shooting distance when shooting subjects where the correct exposure is difficult to obtain in the TTL or Non-TTL auto flash mode. The flash output level can be set from M1/1 (full output) to M1/128 to match your creative preferences.

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Press the a button until G appears on the LCD panel.

3 Determine the flash output level and aperture to match the flash shooting distance. For details on determining the flash output level and

the aperture, refer to Determining the aperture and flash output level in the Manual mode (p. 42).

4 Press the g button to highlight the flash output level display, then press the e or f button to increase or decrease the values. Refer to Setting the flash output level (p. 47).

5 Set the aperture. For cameras compatible with CLS, digital SLRs not

compatible with CLS, cameras in Groups I and II with CPU lenses, and COOLPIX cameras compatible with i-TTL, set the SB-800s aperture on the camera. You cannot set the aperture on the SB-800 directly.

For other camera/lens combinations, press the g button to highlight the aperture display, then press the e or f button to increase or decrease the aperture value.

If the ISO sensitivity is correctly set, the flash shooting distance appears on the LCD panel, matching the flash output level and aperture as set.

47

D et

ai le

d op

er at

io n

6 Set the same aperture on your camera or lens that is set on the SB-800. With cameras in Groups III to VII.

7 Confirm that the ready-light comes on, then shoot.

Setting the flash output level Press the g button to highlight the flash output level display. The flash output level changes every time you press the e or f button as shown below.

When you press the f button: 1/1 1/2 1/2 (1/3) 1/2 (2/3) 1/4

1/128 … 1/4 (2/3) 1/4 (1/3)

When you press the e button: 1/128 1/128 (+1/3) 1/128 (+2/3) 1/64

1/1 1/2 … 1/64 (+2/3) 1/64 (+1/3)

The numbers in parentheses represent the adjustable flash output level in 1/3 steps except between 1/1 and 1/2. Therefore, 1/32 (-1/3) and 1/64 (+2/3) represent the same flash output level.

To extend the flash shooting distance, choose a flash output level close to M1/1.

48

Manual mode

Repeating q flash In Repeating flash operation, the SB-800 fires repeatedly during a single exposure, creating stroboscopic multiple-exposure effects. This operation is useful when shooting fast-moving subjects. In this operation, q appears on the LCD panel. Be sure to use fresh or fully charged batteries and allow enough time for the flash to

recycle between each repeating flash session. Also, it is recommended to use a tripod to prevent camera/flash shake, because slower

shutter speeds are used.

Setting the flash output level, the frequency (Hz), and the number of repeating flashes per frame

Frequency (Hz) represents the number of times the flash fires per second. The actual number of repeating flashes per frame becomes lower than the one set as

the shutter speed increases or the number of flashes per second decreases, because the Speedlight fires during a single exposure.

Referring to the table below, set the flash output level, the frequency, and the number of repeating flashes separately for each picture.

Maximum number of repeating flashes per frame

* Frequency (Hz) represents the number of flashes per second.

1 Set the cameras exposure mode to Manual (M).

Frequency* Flash output level

1/8 1/16 1/32 1/64 1/128 1-2 Hz 14 30 60 90 90 3 Hz 12 30 60 90 90 4 Hz 10 20 50 80 80 5 Hz 8 20 40 70 70 6 Hz 6 20 32 56 56 7 Hz 6 20 28 44 44 8 Hz 5 10 24 36 36 9 Hz 5 10 22 32 32

10 Hz 4 8 20 28 28 20-100 Hz 4 8 12 24 24

49

2 Press the a button to display q.

3 Press the g button to highlight the flash output level display, then press the e or f button to increase or decrease the values. The available range of the flash output level is

between 1/8 and 1/128.

4 Press the g button. The flash output level is set, then the frequency

display is highlighted.

5 Repeat the procedures above to set the frequency and the number of repeating flashes per frame.

Frequency (Hz) Number of repeating flashes per frame

6 Determine the guide number according to the flash output level and zoom-head position set, then calculate the correct aperture from the guide number and the shooting distance. Finally set this aperture on the SB-800. Refer to Guide number table (p. 42) and

Determining the aperture and flash output level in the Manual mode (p. 42).

For cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I and II with CPU lenses, set the SB-800s aperture on the camera. You cannot set the aperture on the SB-800 directly.

If the ISO sensitivity is correctly set, the flash shooting distance appears on the LCD panel, matching the flash output level and aperture as set.

D et

ai le

d op

er at

io n

50

Manual mode

7 Set the same aperture on the camera or lens that is set on the SB-800. With cameras in Groups III to VII.

8 Set the shutter speed. Use the equation to determine the shutter speed and

use that shutter speed or one slower.

Shutter speed = Number of flashes per frame Frequency of flashes (Hz)

For example, if the number of flashes per frame is 10 and frequency is 5 Hz, divide 10 by 5 to get a shutter speed of 2 sec. or slower.

Or you can set the shutter speed to B (bulb) to accommodate any number of repeating flashes.

9 Confirm that the ready-light is on, then shoot.

t Making sure the flash fires correctly before shooting Press the FLASH button to make sure the flash fires correctly as set.

t Exposure compensation in Repeating flash operation The flash shooting distance calculated in step number 6 is the correct exposure for the first flash in the sequence. Therefore, repeating flash at this flash output level will result in overexposure of any overlapping images. To prevent this, set a smaller aperture on the camera.

51

Notes on continuous flash shooting

Do not exceed the maximum number of continuous firings You should allow the SB-800 to cool off for at least 10 minutes after the maximum number of continuous firings are performed as shown in the table below:

Max. number of continuous firings Flash mode Max. number of continuous firings

(at 6 frames/sec.)

TTL auto flash Non-TTL auto flash/Auto Aperture flash 15 Manual flash (Flash output level: M1/1, M1/2)

Manual flash (Flash output level: M1/4 to M1/128) 40

Synchronization during continuous flash shooting It is possible to take up to the number of frames during continuous shooting as shown in the table below. However, if the continuous firings exceed the maximum numbers as shown in the table above, you should allow the SB-800 to cool off for at least 10 minutes.

Maximum number of frames during continuous flash shooting (at six frames per sec.)

With fresh batteries of the same type in both the SB-800 and optional Nikon SD-8A or Power Bracket Unit SK-6/SK-6A.

Refer to table Maximum number of repeating flashes per frame on page 48 when performing Repeating flash.

D et

ai le

d op

er at

io n

1/8 1/16 1/32 1/64 1/128

Up to 4 Up to 8 Up to 16 Up to 30 Up to 40

SD-7 Alkaline-manganese Alkaline-manganese Lithium NiCd Ni-MH Alkaline-manganese Lithium NiCd Ni-MH

Up to 6 Up to 10 Up to 40 Up to 40 Up to 40 SD-8A

Up to 5 Up to 10 Up to 20

Up to 30 Up to 40 Up to 40

Up to 5 Up to 10 Up to 40 Up to 40Up to 30

SK-6/ SK-6A Up to 5 Up to 10 Up to 20 Up to 40 Up to 40

Up to 5 Up to 10 Up to 30 Up to 40 Up to 40

Batteries inside SB-800

Flash output level

SB-800 only All types

Optional power source

WARNING

52

Checking the correct exposure before shooting

You can determine whether the subject will receive the correct exposure by test firing the SB-800 before actually taking the picture in TTL auto flash, Auto Aperture, and Non-TTL auto flash operations. In manual flash mode, checking the correct exposure cannot be performed by

test firing.

TTL auto flash mode Press the SB-800s a button until B (Auto Aperture flash) or A (Non- TTL auto flash) appears on the LCD panel. Set the same aperture on the SB-800 as set in the TTL auto flash mode. Press the shutter release button slightly, then press the FLASH button to fire the flash. If the ready-light blinks after firing, this indicates the light may have been insufficient for correct exposure. In this case, set a wider aperture on the camera or lens, or move closer to the subject.

Auto Aperture flash Make the necessary settings on the SB-800 and camera, press the shutter release button slightly, then press the FLASH button to fire the flash. If the ready-light blinks after firing, this indicates the light may have been insufficient for correct exposure. In this case, set a wider aperture on the camera or lens, or move closer to the subject.

Non-TTL auto flash Make the necessary settings on the SB-800 and camera, then press the FLASH button to fire the flash. If the ready-light blinks after firing, this indicates the light may have been insufficient for correct exposure. In this case, set a wider aperture on the camera or lens, or move closer to the subject.

Other functions

Detailed information on each function of the SB-800 is provided.

54

Exposure compensation and flash output level

Exposure compensation allows you to take well-balanced pictures by intentionally modifying the flash exposure. This is useful when a subject of extremely high or low reflectivity is included in the scene or when you want to create flash photographs to match your creative preferences. Some plus compensation may be necessary when the background includes a mirror,

white wall, or other highly reflective surface. Likewise, some minus compensation may be required when the background is dark or includes subjects of low reflectivity.

Making exposure compensation for both the main subject and background, the main subject only without affecting the background, or the background only without affecting the main subject are possible, depending on the flash shooting situation.

Exposure compensation on the SB-800 can be performed in these ways:

Exposure compensation Available flash mode Usable camera Making exposure compensation All flash modes Cameras in all groups for both the main subject and background Making exposure compensation TTL auto flash and Auto Cameras compatible with CLS, for the main subject only Aperture flash digital SLRs not compatible

with CLS, cameras in Groups I to III, and COOLPIX cameras compatible with i-TTL.

Manual flash mode Cameras in all groups Making exposure compensation Flash shooting at slow shutter Cameras in all groups for the background only speeds

Making exposure compensation for both the main subject and background In TTL auto flash mode and Auto Aperture flash operation Use the cameras exposure compensation function to modify both the SB-800s flash output level and the background exposure. For details, see your cameras instruction manual. The exposure compensation value set on the camera is not displayed on the SB-800s

LCD panel. Exposure compensation beyond the usable ISO sensitivity range cannot be performed

(p. 24). For example, with an ISO sensitivity of 100, if you try to make an exposure compensation of +3 steps on the camera (equivalent to ISO 12), which is out of the usable ISO sensitivity range (ISO 25-1000) of the SB-800. In this case, exposure compensation up to +2 steps (equivalent to ISO 25) is possible.

55

compensation

Making exposure compensation in Non-TTL auto flash and Manual flash operations Exposure compensation is performed by intentionally modifying the correct aperture. In the Non-TTL auto flash mode, the correct exposure can be obtained when the same

aperture is set on the camera as that set on the SB-800. Therefore, to make exposure compensation, vary the aperture set on the camera while retaining the aperture set on the SB-800 or vice versa.

In the Manual flash mode, calculate the proper aperture for the correct exposure from the guide number and the shooting distance (p. 43). Then, use a larger or smaller aperture on the camera to make exposure compensation.

As a basic guide, set a wider aperture on the camera or lens to make the main subject brighter or a smaller aperture to make it darker.

Making exposure compensation for the main subject only In TTL auto flash mode and Auto Aperture flash operation Making exposure compensation for a flash illuminated main subject without affecting the background exposure by adjusting the SB-800s flash output level is called flash output level compensation (p. 56). This compensation can only be performed with cameras compatible with CLS, digital

SLRs not compatible with CLS, cameras in Groups I to III, and COOLPIX cameras compatible with i-TTL.

In Manual flash mode Making exposure compensation for only the flash illuminated subject by intentionally modifying the SB-800s flash output level (M1/1 to M1/128). For cameras in all groups.

Making exposure compensation for the background only Set the cameras exposure mode to Shutter-Priority Auto (S) or Manual (M), and set the shutter speed to one slower than its flash sync shutter speed. With cameras providing slow-sync, set the cameras flash sync mode to Slow-sync

(p. 58) to bring out background details in low-light situations. For details, see your cameras instruction manual.

O th

er f

un ct

io ns

56

Exposure compensation and flash output level compensation

Flash output level compensation You can make exposure compensation for the flash illuminated subject without affecting the background exposure by modifying the SB-800s flash output level. Available in TTL auto flash mode, Auto Aperture flash and Distance-priority manual

flash operations. In the TTL auto flash mode or Auto Aperture flash operation, flash output level

compensation is only available with cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to III, and COOLPIX cameras compatible with i-TTL.

With F-601/N6006 and F-601M/N6000 cameras, make flash output level compensation on the camera. Flash output level compensation cannot be made on the SB-800. The amount of compensation set on the camera does not appear on the SB-800s LCD panel. For details, see your cameras instruction manual.

With SLR cameras that have a built-in Speedlight with an exposure compensation function, you can compensate the flash output level on either the camera or the SB-800. For details, see your cameras instruction manual. If you use both controls, the exposure is modified by the sum total of both compensation values. In this case, the SB-800s LCD panel shows only the compensation value set on the SB-800.

1 Press the g button to highlight the Flash output level compensation value.

2 Press the e or f button to increase or decrease the compensation in 1/3 steps from 3.0 to +3.0 EV.

3 Press the g button. The highlighted flash output level compensation value

returns to normal display. The last highlighted number is the one automatically set.

v Canceling flash output level compensation The flash output level compensation cannot be canceled by turning the SB-800 off. To cancel, press the e or f button to return the compensation value to 0.

57

Flash shooting distance range with zoom lenses having a variable aperture

With zoom lenses having a variable aperture, take note of the following before setting the aperture on the SB-800 and confirming the flash shooting distance range. For details, read the instruction manuals of your camera and lenses.

u Lenses having a variable aperture There are two maximum aperture values indicated in the lens model name of certain zoom lenses. For example with the AF Zoom-Nikkor 28-105mm f/3.5- 4.5D IF, the maximum aperture at 28mm is f/3.5, but decreases to f/4.5 at 105mm.

Setting the aperture on the cameras LCD panel or in the viewfinder Lock the lens aperture at its minimum. After composing the picture by zooming in or out, read the aperture on the cameras LCD panel or in the viewfinder. Then set the same aperture on the SB-800s LCD panel and confirm the flash shooting distance range.

Setting the aperture using the scale on the lens After zooming in or out to select the appropriate composition, read the aperture using the aperture scale on the lens. Then set the same aperture on the SB-800s LCD panel and confirm the flash shooting distance range.

At wideangle zoom settings, read the aperture value at the green index (or line). At telephoto settings, read the aperture value at the yellow index (or dot). At intermediate settings, read the aperture value between the two indexes.

Setting the aperture on the cameras aperture dial (F-401x/N5005, F-401s/N4004s, F-401/N4004 cameras + CPU lens) After zooming in/out to select the desired composition, set the aperture on the cameras aperture dial. Then set the same aperture on the SB-800s LCD panel and confirm the flash shooting distance range. Set the cameras exposure mode to Aperture-Priority Auto (A) or Manual (M).

The aperture cannot be set in the Programmed Auto (P) or Shutter-Priority Auto (S) exposure mode.

If the aperture dial is set beyond lens aperture range, set the lens minimum (or maximum) aperture on the SB-800s LCD panel.

O th

er f

un ct

io ns

58

Slow-sync flash mode, Red-eye reduction control,

Slow-sync flash The flash is controlled at a slow shutter speed to obtain the correct exposure for both the main subject and background in low-light situations or at night. Available with cameras providing slow-sync. You cannot set the slow-sync function on

the SB-800 directly, but must set it on the camera. For more information, refer to your cameras instruction manual.

Since slow shutter speeds are normally used, use of a tripod is recommended to prevent camera shake.

Red-eye reduction To prevent the center of your subjects eyes from appearing red in color pictures, the SB-800 fires three flashes at reduced output just before the picture is taken. Available with cameras having red-eye reduction control. You cannot set red-eye

reduction on the SB-800 directly, but must set it on the camera. For more information, refer to your cameras instruction manual.

After setting your camera to red-eye reduction, make sure that N appears on the SB-800s LCD panel.

Red-eye reduction with slow-sync flash mode In this mode, red-eye reduction is combined with slow sync. Available with cameras having red-eye reduction with slow-sync. You cannot set this

mode on the SB-800 directly, but must set it on the camera. For more information, refer to your cameras instruction manual.

After setting your camera to red-eye reduction with slow sync, make sure that N appears on the SB-800s LCD panel.

Since slow shutter speeds are normally used, use of a tripod is recommended to prevent camera shake.

59

and Rear-curtain sync

Rear-curtain sync In normal flash photography, when shooting fast-moving subjects at slow shutter speeds, unnatural-looking pictures can occur, because the subject frozen by the flash appears behind or within the blurred movement (see photo below right). Rear-curtain flash sync creates a picture in which the blur of a moving subject (for example, the taillights of a car) appears behind the subject and not in front. In front-curtain sync, the flash fires immediately after the front curtain opens completely;

in rear-curtain sync, the flash fires just before the rear curtain starts to close. Available with cameras providing rear-curtain sync. You cannot set this mode on the

SB-800 directly, but must set it on the camera. For details, see your cameras instruction manual.

Since slow shutter speeds are usually used, use a tripod to prevent camera shake. This function does not operate in Repeating flash operation. In multiple flash, the master flash unit can be set to either front-curtain or rear-curtain

sync flash. However, the remote units cannot be set to rear-curtain sync flash (p. 72).

Rear-curtain sync Front-curtain sync

Shooting data Focal length: 70mm Shutter speed: 2 sec. Aperture: f/4.5 Flash mode: Manual Flash output level: M1/1

O th

er f

un ct

io ns

60

Auto FP High-Speed Sync mode (for compatible cameras)

High-Speed flash synchronization at your cameras highest shutter speed is now possible. In this mode, the Auto FP High-Speed Sync mode is automatically set when the shutter speed exceeds the cameras sync shutter speed. This is useful when you want to use a wider aperture to achieve shallow depth of field to blur the background. Available with compatible cameras. You cannot set the Auto FP High-Speed sync mode

on the SB-800 directly, but must set it on the camera. High-speed flash synchronization is possible exceeding your cameras sync shutter

speed up to your cameras highest shutter speed. Auto FP High-Speed sync also operates in the Advanced Wireless Lighting mode. Available flash modes are i-TTL, Auto Aperture flash, Distance-priority manual flash, and

Manual flash when using a single flash unit. i-TTL, Auto Aperture flash, Non-TTL auto flash, and Manual flash are available in multiple flash operation.

61

Flash Value Lock (FV Lock) (for compatible cameras)

Flash Value, or FV, is the amount of flash exposure for the subject. Using FV Lock with compatible cameras, you can lock in the appropriate flash exposure for the main subject. This flash exposure remains locked in, even if you change the aperture or composition, or zoom the lens in and out. Available with compatible cameras. You cannot set the FV Lock function on the SB-800

directly. Set it on the camera. Available flash modes are i-TTL, Auto Aperture flash and Non-TTL auto flash.

O th

er f

un ct

io ns

62

Autofocus flash operation in dim light

When the light is too dim for normal autofocus operation, the SB-800s Wide- Area AF-Assist Illuminator enables you to perform autofocus flash photography. In dim light, the Wide-Area AF-Assist Illuminator turns on automatically when the

cameras shutter release button is lightly pressed, if an AF lens is mounted and the cameras focus mode is set to S (Single Servo AF with focus priority), AF, or A.

The effective shooting distance with the Wide-Area AF-Assist Illuminator is approx. 1m to 10m (3.3 to 33 ft.) with a 50mm f/1.8 lens or less, depending on the lens in use.

Usable lens focal length: 24mm to 105mm (35 to 105mm for F-501/N2020 cameras).

Use the center focus area in your cameras viewfinder when using the wide-area AF-Assist Illuminator.

t For cameras compatible with CLS The SB-800s Wide-Area AF-Assist Illuminator supports the dynamic-area AF system of

cameras compatible with CLS. With a D2H camera, for example:

Usable lens focal length: 24mm to 105mm. A total of 11 focus areas are usable at a lens focal length of 35mm or longer as shown in the figure below. A total of 9 focus areas excluding the extreme right- and left-hand ones are usable at a lens focal length of less than 35mm.

With AF cameras such as the D2H, the effective shooting range of the wide-area AF-assist Illuminator is approx. 1m to 10m (3.3 to 33 ft.) or less in the mid portion of the frame, and 1m to 7m (3.3 to 23 ft.) or less at the periphery (with a 50mm f/1.8 lens). These ranges may vary depending on the lens in use.

For details, see your cameras instruction manual.

63

v Notes on using the Wide-Area AF-Assist Illuminator If the focus indicator does not appear in the cameras viewfinder even through the Wide-

Area AF-Assist Illuminator turns on, focus manually. The Wide-Area AF-Assist Illuminator will not light up, if the cameras autofocus is locked

or the SB-800s ready-light does not come on. Refer to your cameras instruction manual for more information.

t Activating and canceling the Wide-Area AF-Assist Illuminator You can set the SB-800s Wide-Area AF-Assist Illuminator to activate or cancel in the Custom settings mode (p. 67). By default, the Wide-Area AF-Assist Illuminator is set to activate.

t Canceling the SB-800s flash firing but not the Wide-Area AF-Assist Illuminator

The SB-800s Wide-Area AF-Assist Illuminator comes on but the flash unit will not fire when FIRE is set to OFF (canceled) in the Custom settings mode (p. 67). By default, FIRE is set to ON.

t For cameras having a built-in Speedlight Even when the cameras AF-Assist Illuminator is set to activate, the SB-800s Wide-Area

AF-Assist Illuminator is given priority and the cameras AF-Assist Illuminator does not light up. However, the cameras AF-Assist Illuminator lights up only when the SB-800s Wide-Area AF-Assist Illuminator is canceled.

With F80-Series/N80-Series, F75-Series/N75-Series and F65-Series/N65-Series cameras, the cameras AF-Assist Illuminator lights up when the SB-800s Wide-Area AF-Assist Illuminator is canceled. To cancel the cameras AF-Assist Illuminator, cancel it on the camera. For details, refer to your cameras instruction manual.

With F60-Series/N60 cameras, the cameras AF-Assist Illuminator lights up while shooting at full output manual. For details, refer to your cameras instruction manual.

u Using the SB-800 off-camera When using the SB-800 off-camera with the TTL Remote Cord SC-29, autofocus flash photography in dim light is possible, because the SC-29 features an AF-assist illuminator function (p. 111).

O th

er f

un ct

io ns

64

Using the Quick Recycling Battery Pack SD-800

Use the provided quick recycling battery pack to install five batteries to shorten the recycling time (p. 19).

Notes on using the Quick Recycling Battery Pack SD-800 With the SD-800 attached, be sure to use five batteries. Be sure to replace all five batteries, including the one in this pack and

the four inside the SB-800, with fresh ones at the same time. Do not mix battery brands or types, or use old with new batteries.

Otherwise, the batteries may leak corrosive liquids, become hot, or explode.

This battery pack cannot be used when the Power Bracket Unit SK-6/SK-6A is attached to the SB-800.

The battery chamber lids for the SB-800 and SD-800 are identical.

Attaching the Quick Recycling Battery Pack SD-800

1 Slide the SB-800s battery chamber lid in the direction of the arrow to open.

2 Push the battery chamber lid back in the direction of the arrow to remove it. The lid can be easily removed if pushed back past

the perpendicular position.

WARNING

Battery chamber lid

Battery chamber lid attachment index

Quick recycling battery pack lock switch

65

3 Install the batteries in accordance with the i and j marks, as shown.

4 Open the SD-800s battery chamber lid to install an extra battery, following the i and j marks, as shown.

5 Close the battery chamber lid by sliding it into place while pressing down.

6 Align the index mark on the SD-800s battery chamber lid with the corresponding index mark on the SB-800 and attach the battery pack by sliding it into place. Be sure to slide the battery pack until the SD-800s

lock switch clicks into place.

Detaching the SD-800. O

th er

f un

ct io

ns

Index

1 Push up the SD-800s lock switch, then slide it to detach.

2 Insert one of the hinges of the SB-800s battery chamber lid, as shown.

3 Insert the other hinge, as shown.

4 Close the battery chamber lid by sliding it into place while pressing down.

66

Checking the illumination before actually taking the picture (Modeling illuminator)

Press the Modeling illuminator button and the flash fires repeatedly at a reduced flash output level. This is useful for checking the illumination and the shadows cast on the subject before actually taking the picture. The flash fires as a Modeling illuminator for a maximum of approx. 3 sec. while the

Modeling illuminator button is pressed. This function operates only after the ready-light comes on.

Modeling illuminator with cameras attached When the Modeling illuminator button on the master (SB-800) flash unit or the preview button on a camera compatible with the modeling illuminator is pressed, the modeling illuminator fires. For details, see your cameras instruction manual.

Modeling illuminator in the Advanced Wireless Lighting (p. 76) (Available with cameras compatible with CLS)

When the Modeling illuminator button on the master flash unit is pressed, the Modeling illuminator of the highlighted master unit or grouped remote flash units fire. If the master flash unit and grouped remote flash units are not highlighted, the Modeling

illuminator of the master flash unit only fires (except when the master flash units flash firing is set to canceled.)

When the preview button on a camera compatible with the modeling illuminator is pressed, the modeling illuminators of the master and all other remote flash units fire. Both the master and remote flash units fire at the flash output level compensation value

as set.

Modeling illuminator in SU-4 type wireless multiple flash operation (p. 84)

When the Modeling illuminator button on the master (SB-800) flash unit or the preview button on a camera compatible with the modeling illuminator is pressed, only the modeling illuminator of the master flash unit fires. When the SB-800 is set as a remote flash unit, the Modeling illuminator does not fire

even when the Modeling illuminator button is pressed.

v Do not release the shutter while the modeling illuminator is firing If you release the shutter while the master flash units modeling illuminator is firing, correct exposure cannot be obtained.

67

Custom functions

The SB-800 can easily set, activate, or cancel various operations using the Custom settings as shown below. Icons appearing on the LCD panel vary depending on the settings and the camera/lens combinations. No icon appears when the settings are not available. For details on setting custom functions, see Custom settings (p. 68).

Available Custom functions and the icons

ISO sensitivity (p. 24)

Wireless flash mode (p. 72)

Sound monitor in the wireless flash mode (p. 89)

Non-TTL auto flash mode (p. 38)

Standby function (p. 21)

Selecting the distance unit of measure (m, ft)

Power zoom function (p. 26)

Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally (p. 117)

LCD panel illuminator (p. 119)

LCD panel brightness (p. 119)

Wide-area AF-Assist Illuminator (p. 62)

Canceling flash firing (p. 62)

O th

er f

un ct

io ns

68

Custom settings

Setting Custom functions

1 Press the g button for approx. 2 sec. to display the Custom settings mode.

2 Press the e or f button and c or d button on the Multi Selector to choose the desired custom functions to be set, then press the g button.

3 Press the e or f button to highlight the preferred setting. Press the c or d button to adjust the LCD panel

brightness

4 Press the g button for approx. 2 sec. or press the b button to return to the normal setting mode.

69

Details on Custom settings (Bold: default setting)

ISO sensitivity (p. 24) The available ISO sensitivity range is ISO 3 to 8000. Pressing the e or f button increases or decrease the value in increments of 1/3 step. Pressing the e or f button continuously increases or decreases the value quickly. 100

Wireless flash mode (p. 72) Setting the flash mode in wireless multiple flash photography. OFF : Canceled MASTER : Master flash unit in the Advanced Wireless

Lighting mode MASTER (RPT) : Master flash unit in the Advanced Wireless

Lighting mode (in Repeating flash) REMOTE : Remote flash unit in the Advanced Wireless

Lighting mode SU-4 : SU-4 type wireless flash mode

Sound monitor in the wireless flash mode (p. 89) When the SB-800 is used as a wireless remote flash unit, you can activate or cancel the sound monitor function. ON : Sound on OFF : Sound off

Non-TTL auto flash mode (p. 38) Setting the Non-TTL auto flash mode. AA : Auto Aperture flash A : Non-TTL auto flash

Standby function (p. 21) Adjusting the time before the standby function is activated. AUTO : With a camera body that is compatible with TTL auto flash (p. 8),

the SB-800 turns off when the cameras exposure meter turns off. 40 : 40 sec. 80 : 80 sec. 160 : 160 sec. 300 : 300 sec. — — — : Standby function canceled

O th

er f

un ct

io ns

70

Custom settings

Selecting the distance unit of measure (m, ft) Setting the distance unit of measure on the LCD panel to either meters m or feet ft. m : meters ft : feet

Power zoom function (p. 26) Setting to activate or cancel the power zoom function, which adjusts the zoom-head position automatically. OFF : Activated ON : Canceled

Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally (p. 117) Setting to activate or cancel the zoom-head position setting if the built-in wide-flash adapter is broken off accidentally. When set to ON, the zoom- head position display or AUTO indicator (if using a COOLPIX camera compatible with i-TTL) is framed. OFF : Manual setting canceled ON : Manual setting activated

LCD panel illuminator (p. 119) Setting the LCD panel illuminator to turn on or off. ON : Turn on OFF : Turn off

LCD panel brightness (p. 119) Adjusting the brightness of the LCD panel. Available brightness levels are graphically displayed in 9 steps on the LCD panel. Press the c or d button to adjust the brightness.

Wide-Area AF-Assist Illuminator (p. 62) Setting to activate or cancel the Wide-Area AF-Assist Illuminator. ON : Activated (AF-ILL appears on the LCD panel) OFF : Canceled (NO AF-ILL appears on the LCD panel)

Canceling flash firing (p. 62) Setting to activate or cancel flash firing of the SB-800. When it is set to OFF, the SB-800 does not fire but the Wide-Area AF-Assist Illuminator still comes on. ON : Firing activated OFF : Firing canceled (AF-ILL ONLY appears on the LCD panel)

Advanced operations

Information on advanced flash shooting techniques using the SB-800 is described in this section.

72

Overview of multiple flash operation

Multiple flash photography allows you to create more natural-looking pictures by using several flash units to emphasize the subjects shape or eliminate shadows. The following wireless multiple flash operations are available:

Multiple flash operation Advanced Wireless Lighting (p. 76)

SU-4 type wireless multiple flash (p. 84)

Multiple flash operation using cords (p. 90)

Its not possible to use different types of multiple flash operations together. Wireless multiple flash operation using Speedlights featuring CLS is called Advanced

Wireless Lighting.

For cameras compatible with CLS and digital SLRs not compatible with CLS, set the master flash units flash mode to Auto Aperture B flash or Non-TTL auto A flash in SU-4 type wireless multiple flash operation. In multiple flash operation using cords, multiple flash shooting in M (manual) mode only is possible.

t Master flash unit and remote flash unit(s) In this instruction manual, the flash unit mounted on the camera or the one directly connected to the camera via a TTL Remote Cord, such as the SC-17, SC-28 or SC-29, is called the master flash unit. All other flash units are called the remote flash units.

Usable cameras

Cameras compatible with CLS

No limitation

No limitation (TTL multiple flash operation is not possible with digital SLRs.)

Usable Speedlights

Only those featuring CLS such as SB-800 for both the master and remote flash units. Master flash unit: Speedlights compatible with wireless flash operation, those compatible with the TTL mode, or the built- in Speedlights on cameras so equipped. Remote flash unit: Except the SB-23, all Speedlights compatible with wireless flash operation or those connected to the optional Wireless Slave Flash Controller SU-4. Speedlights compatible with the TTL mode. Speedligthts SB-11, SB-14,

SB-140, and SB-21B cannot be used with the F-401/ N4004 or F-401s/N4004s as either master or remote flash units.

73

Be sure to cancel Monitor Preflashes (in TTL multiple flash operation)

In SU-4 type wireless multiple flash and multiple flash using cords, cancel the Monitor Preflashes of the master flash unit following one of the methods described below, since Monitor Preflashes cause incorrect exposure.

SB-800 Set the SU-4 type wireless multiple flash mode

SB-80DX, SB-50DX Set the wireless flash mode. SB-800, SB-600, SB-80DX, Set the flash mode to Standard TTL flash. SB-50DX, SB-28, SB-28DX, Tilt the flash head up. SB-27, SB-26, SB-25 Use a non-CPU lens. Built-in Speedlight Set the exposure mode to M (Manual). (F80-Series/N80-Series, F75-Series/ N75-Series, F70-Series/N70)

v Notes on performing multiple flash (common to both wireless and wired operation) To avoid accidental firing, turn off the camera and all flash units before mounting the

master flash unit on or connecting it to the camera. When using a Speedlight that has a standby function as a remote flash unit, make sure

that the standby function is set to off, or select a standby duration that is long enough, using the Custom settings.

The SB-800s and SB-80DXs standby function is canceled while the SB-50DXs standby duration is prolonged to approx. one hour when they are set to the wireless remote flash mode.

Set the angle of coverage of the remote flash units wider than the picture angle, so that the subject will receive sufficient illumination even when the angle of the flash head is off axis from the subject. (In Advanced Wireless Lighting, the zoom-head position is automatically set to 24mm, except when the built-in wide-flash adapter or Nikon Diffusion Dome is attached.) Remember, the closer the subject, the wider the angle of coverage required.

The brightness of the flash illumination is inversely proportional to the square of the distance between the flash unit and the subject. For example, if the distance between Speedlight A and the subject is 1m (3.3 ft.), and Speedlight B is 2m (6.6 ft.), the combined brightness of the two Speedlights will be:

A : B = 12 : 22 = 1 : 4 (in meters) or 3.32 : 6.62 = approx. 11 : 44 (in feet) Therefore, the illumination provided by Speedlight A is four times (or two steps) brighter than that provided by Speedlight B.

To ensure good results, its recommended to make test shots before shooting important events.

Be sure to read the instruction manuals of your camera and Speedlight(s) before use.

A dv

an ce

d op

er at

io ns

74

Wireless multiple flash shooting

Read the following when setting up the SB-800 as a remote flash unit in the Advanced Wireless Lighting and SU-4 type wireless multiple flash modes.

Flash set-up in the Advanced Wireless Lighting Set up the camera, master flash unit, and remote flash units as shown in the figure below.

As a basic guide, the effective shooting distance between the master and remote flash units is approx. 10m (33 ft.) or less in the front position, and approx. 5 to 7m (16 to 23 ft.) at both sides. These ranges vary slightly depending on the ambient light.

Be sure to place all remote flash units that are set in the same group close together. For the effective shooting distance between the master and remote flash units in SU-4

type wireless multiple flash shooting, refer to page 85.

v Setting up the master and remote flash units In most cases, position the remote flash unit(s) closer to the subject than the camera,

so that light from the master flash unit can reach the light sensor of the remote flash unit(s). This is particularly necessary when holding a remote flash unit in your hand.

Data communication cannot be performed properly if there is an obstacle between the master unit and remote flash units.

Take care not to let light from the remote flash unit enter the camera lens directly or indirectly in TTL auto flash mode. Also, prevent light from entering the master flash units light sensor in Non-TTL auto flash mode. Otherwise, the correct exposure cannot be obtained.

There is no limit to the number of remote flash units that can be used together. However, if too much light from other remote flash units enters the light sensor of the master flash unit, correct operation may be impossible. Practically, the number of remote flash units in Advanced Wireless Lighting should be limited to three for one group.

Use the provided Speedlight Stand AS-19 for stable placement of the remote flash units. Be sure to perform test firing after setting up all flash units (p. 20).

Be sure to direct the light sensor window of the remote flash unit toward the master flash.

Master flash unit

Less than approx. 10m (33 ft.)

Approx. 5 to 7m (16 to 23 ft.)

Group A

Group C

Group B Within 30

Within 30

Approx. 5 to 7m (16 to 23 ft.)

75

Using the Speedlight Stand Use the provided Speedlight Stand AS-19 for stable placement of the remote flash units. You can also use the stand for setting up your Nikon Speedlight when using it as a

remote flash unit in multiple flash shooting using cords (p. 90).

Attachment to the Speedlight Stand

1 Attach the SB-800 to the Speedlight Stand in the same way that you attach it to the cameras accessory shoe. The same is true when detaching it from the camera.

t To prevent the remote flash units from firing accidentally Effective for the SU-4 type wireless multiple flash only

Do not leave the power of the remote flash units on. Otherwise, ambient electric noise due to a discharge of static electricity, etc. may trigger them accidentally.

If you are holding the remote flash unit in your hand, press the Modeling illuminator button/Wireless remote flash cancel button on the SB-800 to avoid accidental firing in sync with other Speedlights. The SB-800 will not fire, while this button is pressed.

FLASH

READ

A dv

an ce

d op

er at

io ns

Speedlight mounting shoe (for all Speedlights except the SB-15 and SB-27)

Speedlight mounting shoes for the SB-15 and SB-27

Tripod socket Setup example using the SB-27

76

When the SB-800 is used with Nikon cameras compatible with CLS, Advanced Wireless Lighting is possible. In this mode, you can divide the remote flash units into a maximum of three groups (A, B, C) and set the flash mode and flash output level compensation values separately for each group as well as the master flash unit, providing automatic control of the light output.

Setting the SB-800 to Advanced Wireless Lighting You can set the SB-800 to Advanced Wireless Lighting using Custom settings (p. 67).

Select MASTER to set the SB-800 as the master flash unit in the Custom settings mode. The indicator O appears on the LCD panel. In case of performing Repeating flash operation, select MASTER (RPT) instead

of MASTER.

MASTER MASTER (RPT)

Select REMOTE to set the SB-800 as a remote flash unit in the Custom settings mode. The indicator P appears on the LCD panel. To set group and channel numbers on the remote flash units, see instructions on page 79. To fire the remote flash units via control of the cameras built-in flash in Commander

mode (D300, D200, D80 and D70-series), refer to Built-in flash — Commander mode in the Custom Settings chapter of the cameras instruction manual.

Flash shooting in Advanced Wireless Lighting

77

A dv

an ce

d op

er at

io ns

Settings in Advanced Wireless Lighting In this mode, set the following items on either the master flash unit or the remote flash units.

Item Speedlight to be set Remarks Flash mode Master flash unit The following five flash modes are available:

D : i-TTL mode B(A) : Auto Aperture flash (Non-TTL auto flash) *1

G : Manual flash q : Repeating flash — — — : Flash canceled Set the flash mode of the remote flash units on the master flash unit. The flash mode can be set independently on the master flash unit and for each group of remote flash units*2.

Flash output level Master flash unit Flash output level compensation values of the remote flash compensation units can also be set on the master flash unit. The flash output

level compensation values can be set independently on the master flash unit and for each group of remote flash units.

Communication Master and remote flash Select one of the four available channels. channel*3 units Be sure to set the same channel number for both the master

flash unit and remote flash units

Group name Remote flash units A maximum of 3 groups (A, B, C)

*1 Auto Aperture flash is automatically set when a CPU lens is mounted on cameras compatible with CLS. However, Non-TTL auto flash is set when a non-CPU lens is mounted or Non-TTL auto flash is selected using Custom settings.

*2 If Repeating flash has been set on the master flash unit, either the Repeating flash mode or Flash canceled mode can be set on the remote flash units from the master unit.

*3 If a photographer uses the same type of wireless remote flash setup near you, your remote flash units may accidentally fire in sync with that photographers master flash unit. To avoid this, use a different channel number.

u Commander function The Commander function in Advanced Wireless Lighting enables the SB-800 to act as a commander unit during wireless multiple flash shooting to trigger remote flash units without firing itself. To activate the Commander function, set the SB-800 as the master flash unit and set its flash mode to Flash canceled (—). This operation will normally not affect the correct exposure of the subject, although the exposure might be affected if the subject is close and a high ISO sensitivity has been set. To limit this effect as much as possible, bounce the light by tilting or rotating the SB-800s flash head.

78

Flash shooting in Advanced Wireless Lighting

Setting the flash mode, flash output level compensation values, and channel number on the master flash unit

1 Press the g button on the master flash unit to highlight M, then press the a button to choose the desired flash mode.

2 Press the e or f button to increase or decrease the flash output level compensation values. Compensation values can be set in 1/3 steps from

3.0 to +3.0 EV. The flash output level can be set from M1/1 to M1/128

in the Manual G mode.

3 Press the g button to highlight A, then press the a button to set the flash mode on the remote flash unit within group A. If the master units flash mode has been set to

Repeating flash, the Repeating flash or Flash canceled mode can be set on the remote flash unit.

4 Following step 2 above, set the flash output level compensation values on the remote flash unit within group A.

5 As in steps 3 and 4, set the flash mode and flash output level compensation values on the remote flash units within groups B and C.

6 Press the g button on the master flash unit to highlight the channel number, then press the e or f button to set the channel number.

79

Setting a group and channel number on the remote flash units

1 Press the g button on the remote flash unit to highlight the channel number, then press the e or f button to set the channel number. Be sure to choose the same channel number as set

on the master flash unit.

2 Press the g button on the remote flash unit to highlight the group, then press the e or f button to set the group. For remote flash units where the flash mode and

flash output level compensation values are to be set identically, place these flash units into the same group.

v Notes on using cameras built-in flash in Commander mode

Camera Available flash mode of Usable channel Usable group built-in flash number

D300, D200, D80 TTL, M, — (Flash canceled) 1 to 4 A, B

D70-Series (Flash canceled) 3 A

u Setting in the Repeating flash mode When the master flash unit is set to the q (repeating flash) mode, set the flash output level, the frequency (Hz) and the number of repeating flashes per frame. (Refer to Repeating q flash on page 48.)

1 Press the g button to highlight the flash output level display, then press the e or f button to increase or decrease the values.

2 Press the g button. The flash output level is set, then the

frequency display is highlighted.

3 Repeat the procedures above to set the frequency and the number of repeating flashes per frame.

If Repeating flash has been set on the master flash unit, either the Repeating flash mode or Flash canceled mode can be set on the remote flash units from the master unit.

A dv

an ce

d op

er at

io ns

Number of repeating flashes per frame

Flash output level

Frequency (Hz)

80

Flash shooting in Advanced Wireless Lighting

Examples of flash shooting in Advanced Wireless Lighting

Wireless multiple flash (three flash units) On-camera single flash

The master flash unit M illuminates the subject while the light from the remote flash unit A is bounced off the ceiling to illuminate the background and create a more natural-looking picture. Remote flash unit B is used with a colored gel filter to create the warmth feeling of a fireplace.

Shooting data Camera: D2H Focal length: 25mm Master flash

unit M: SB-800 (D, +1/3 flash output level compensation)

Remote flash unit A: SB-800 (D, +1/3 flash

output level compensation)

Remote flash unit B: SB-800 (G, 1/16 flash

output level)

For more details regarding the above example, see the separate booklet, A collection of example photos.

Remote flash unit A

Remote flash unit B

Master flash unit M

81

A dv

an ce

d op

er at

io ns

1 Set the cameras exposure mode to Aperture- Priority Auto (A).

2 Set the wireless flash mode of the on-camera SB-800 to MASTER using Custom Settings (p. 67).

3 Press the g button on the master flash unit to highlight M, then press the a button to choose D.

4 Press the e button on the master flash unit to set the flash output compensation value to +0.3.

5 Press the g button on the master flash unit to highlight A, then press the a button to set the flash mode to D on the remote flash unit A.

6 Likewise, press the e button on the master flash unit to set the flash output level compensation value to +0.3 on the remote flash unit A.

7 Press the g button on the master flash unit to highlight B, then press the a button to set the flash mode to G on the remote flash unit B.

8 Likewise, press the f button on the master flash unit to set the flash output level to 1/16 on the remote flash unit B.

9 Press the g button on the master flash unit to highlight the channel number, then press the e or f button to set the channel number to 1.

10 Set up remote flash units A and B. Turn the power on, then confirm that the ready-lights come on. Use a tripod or the Speedlight Stand AS-19 for

placement of the remote flash units (p. 75).

11 Set the remote flash units A and B to REMOTE.

12 Set the channel number of the remote flash units A and B to 1. Be sure to choose the same channel number as set

on the master flash unit.

82

Flash shooting in Advanced Wireless Lighting

83

A dv

an ce

d op

er at

io ns

13 Set the group of the remote flash units A and B. Set the remote flash unit A to group A and the remote

flash unit B to group B.

14 Confirm that all the ready-lights of the master and remote flash units are on, then press the FLASH button on the master flash unit to test fire the units. The master flash unit fires first, then the remote flash

units in group A fire, followed by those in group B. If a certain remote flash unit does not fire, change the

setup by moving the remote unit closer to the subject or redirect its light sensor window toward the master flash unit, then test fire the new setup.

You can check the illumination before actually taking pictures using the Modeling illuminator (p. 66).

15 Finally confirm the aperture and flash shooting distance just as in TTL flash shooting, then shoot. Refer to page 17 for TTL flash shooting. Flash operation can be confirmed by the ready-light

or the beeping sound (p. 89).

84

SU-4 type wireless multiple flash shooting

SU-4 type wireless multiple flash can be performed in two ways: (1) In the A (auto) mode, in which the wireless remote flash units start and stop firing in sync with the master Speedlight, and (2) in the M (manual) mode, in which the wireless remote flash units only start firing in sync with the master Speedlight. Speedlights featuring wireless multiple flash capability can be used either as the master

or remote flash unit. Speedlights compatible with TTL auto flash can be used as the master flash unit. The

optional Wireless Slave Flash Controller SU-4 is necessary when you want to use these Speedlights as remote flash units.

The cameras built-in Speedlight can also be used as a master flash unit. There is no limitation in usable cameras.

Setting the SB-800 to SU-4 type wireless multiple flash To perform SU-4 type wireless multiple flash, set the wireless flash mode to SU-4 using Custom settings (p. 67).

Master flash and remote flash units First, set the SB-800s wireless multiple flash mode to SU-4 using the Custom settings,

then attach the SB-800 to the camera. The indicator O appears on the LCD panel telling you that the SB-800 is set as a master flash unit. If you detach the SB-800 from the camera, the indicator automatically changes to P signifying that the SB-800 is set as a remote flash unit.

Notes on the master flash unit When the SB-800 is set as the master flash unit, Monitor Preflashes are canceled. For

other Speedlights, be sure to cancel the master flash units Monitor Preflashes. The following flash modes are recommended for the master flash unit.

Camera group Master flash units flash mode

Cameras compatible with CLS

Digital SLRs not compatible with CLS

Cameras in Groups I to VI

Non-TTL auto flash mode (B or A) TTL mode is not possible, although

icons are displayed when the MODE button is pressed.

TTL mode

Non-TTL auto flash mode (B or A) TTL mode is not possible, although

icons are displayed when the MODE button is pressed.

TTL mode

Digital SLR cameras

Film-based SLR cameras

85

A dv

an ce

d op

er at

io ns

Setting the flash mode on the remote flash units

1 Detach the SB-800, which is already set to the SU-4 type wireless multiple flash mode, from the camera body.

2 The flash mode on the remote flash unit toggles between PA (auto) and PM (manual) every time you press the a button.

A (auto) mode In the A (auto) mode, the remote flash units start and stop firing in sync with the master

flash unit. The maximum shooting distance of the SB-800s light sensor is approx. 7m (23 ft.).

M (manual) mode In the M (manual) mode, the remote flash units only start firing in sync with the master

flash unit. The maximum shooting distance of the SB-800s light sensor is approx. 40m (131 ft.). The flash output level can be set from M1/1 to M1/128.

FLASH

READY

Wireless multiple flash shooting in the A (auto) mode

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Set up all Speedlights as the master and remote flash units.

3 Set the wireless flash mode of all SB-800s used as master and remote flash units to SU-4.

4 Press the a button on the remote flash unit to activate the A mode.

5 Set the flash mode of the master flash unit to the D mode. With Nikon digital SLRs not compatible with CLS,

set the flash mode to Auto Aperture or Non-TTL auto flash.

6 Confirm the aperture and flash shooting distance as in normal TTL auto flash photography, then shoot. See page 17 for more information on the TTL auto

flash mode. See pages 38 and 40 concerning use of Auto

Aperture or Non-TTL auto flash with digital SLRs not compatible with CLS.

Flash operation can be confirmed by the ready-light or the beeping sound (p. 89).

FLASH

READY

86

SU-4 type wireless multiple flash shooting

87

A dv

an ce

d op

er at

io ns

Wireless multiple flash shooting in the M (manual) mode

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Set up all Speedlights as the master and remote flash units.

3 Set the wireless flash mode of all SB-800s used as the master and remote flash units to SU-4.

4 Press the a button on the remote flash unit to activate the w (manual) mode.

5 Set the flash mode of the master flash unit to Manual flash.

6 Confirm the aperture and flash shooting distance as in normal Manual flash shooting, then shoot. See page 46 for more information on Manual flash.

FLASH

READY

88

t Adjusting the flash output level of the remote flash units in the w (manual) mode

Adjusting the flash output level manually Use the following equation to determine the proper manual flash output level of the remote flash unit, depending on your creative preferences.

GN = F x D

where GN is the guide number of the remote flash unit (in meters/feet), F is the lens aperture in use, and D is the distance between the remote flash unit and the subject (in meters/feet).

For example, with the SB-800s zoom-head position adjusted to 28mm when using an ISO sensitivity of 100 if a lens aperture (F) of f/4 is used and the subject distance (D) is 2m (6.6 ft.) away, then shooting a subject at a distance of 2m (6.6 ft.), and a lens aperture of f/4, then

GN (in meters)= 4 x 2 = 8 GN (in feet)= 4 x 6.6 = approx. 26

Therefore, to get the correct exposure, refer to the Guide Number table (p. 42) and adjust the flash output level to M1/16. Refer to Determining the aperture and flash output level in the Manual mode (p. 42).

Adjusting the flash output level in Non-TTL auto flash (A); applicable when using a Speedlight compatible with Non-TTL auto flash mounted on the SU-4 as a remote flash unit Non-TTL auto flash (A) can also be selected on the remote flash unit. In this case, the remote flash unit controls the flash output based on the aperture and ISO sensitivity set on the remote flash unit, and automatically stops firing in sync with the master flash unit (p. 40).

1 Set the same ISO sensitivity on the remote flash unit as set on your camera.

2 Set the same aperture on both the lens and the remote flash unit to obtain the correct exposure. Depending on your creative preferences, you can intentionally overexpose or

underexpose the picture by modifying the aperture. The above setting is applicable ONLY when both the master and remote flash units

are pointed in the same direction. Refer to Setting apertures in Non-TTL auto flash operation (p. 41) for more details.

SU-4 type wireless multiple flash shooting

89

Confirming wireless multiple flash operation using the ready-light or the beeping sound

A dv

an ce

d op

er at

io ns

You can confirm wireless multiple flash operation by checking the ready-light on the SB-800 or the beeping sound during and after shooting.

Using the SB-800s beeping sound in the wireless flash mode When the SB-800 is used as a wireless remote flash unit, you can monitor its operation by listening to the beeping sound (p. 67). This function can be activated or canceled using the Custom settings.

Confirming flash operation using the ready-light or beeping sound

Lights up or does not come on (not blinking)

Lights up or does not come on (not blinking)

Two beeps Fired properly

Blinks for approx. 3 sec.

Blinks for approx. 3 sec.

Beeps for approx. 3 sec.

Both the master and remote flash units have fired at full output and light may have been insufficient for correct exposure. Use a wider aperture and reshoot.

Lights up or does not come on (not blinking)

Blinks for approx. 3 sec.

Beeps for approx. 3 sec.

The remote flash unit has fired at full output and light may have been insufficient for correct exposure. The light sensor could not detect when to stop firing in sync with the master flash unit, because a strong reflection from the remote flash unit itself or light from another remote flash unit may have entered the light sensor window. Change the direction or position of the remote flash unit and reshoot.

Lights up Lights up One beep Ready to fire

Master flash Remote flash unit unit Speedlight condition

Ready-light Ready-light Beeping sound

90

The SB-800 can be used with Speedlights compatible with the TTL auto flash mode to perform multiple flash shooting using cords. Use of the SB-50DX and SB-23 as remote flash units is not recommended, because

the standby function cannot be canceled. Speedlights SB-11, SB-14, SB-140, and SB-21B cannot be used with the F-401/N4004

or F-401s/N4004s as either master or remote flash units. There is no limitation in usable cameras. With digital SLRs and COOLPIX cameras compatible with i-TTL, only manual flash

operation is possible.

The maximum number of flash units to be connected using cords Up to five units including the master flash unit can be used for multiple flash

photography at a total cable length of 10m (33 ft.). Make sure the combined total of the coefficients in the table below for all flash units

used together does not exceed 20 at 20C (68F) or 13 at 40C (104F). If it exceeds these figures, you may not be able to take a second shot after the first one.

In this case, turn off the power of all flash units and reduce the total number of flash units connected.

Speedlight Coefficient

SB-800, SB-80DX, SB-50DX, SB-30, SB-29, SB-29s, SB-28, SB-28DX, SB-27, SB-26, SB-25, SB-24, SB-22s, SB-14, SB-11, SB-140 1

SB-23, SB-21, SB-17, SB-16, SB-15 4

SB-22 6

SB-20 9

Multiple flash shooting using cords

91

Notes on multiple flash shooting using cords Be sure to see the instruction manuals of your cameras, Speedlights, and accessories. Refer to System chart for TTL multiple flash shooting using cords (p. 94) and your

cameras and Speedlights instruction manuals for proper connection. Use the optional TTL Multi-Flash Sync Cords SC-27, SC-26, SC-19 or SC-18 to connect

the SB-800 to more than one remote flash unit. Use the optional Multi-Flash Adapter AS-10, if the remote flash units are not equipped

with multiple flash terminals. Use the optional Multi-Flash Adapter AS-10 to attach the remote flash unit(s) to a tripod. Be sure to cancel the master flash units Monitor Preflashes. Multiple flash shooting using cords can be performed in two modes: (1) TTL multiple

flash; and (2) Manual multiple flash. Performing multiple flash shooting in the Manual mode, however, is not recommended, since it is difficult to obtain the correct exposure. Use the TTL auto flash mode with cameras compatible with TTL auto flash.

To ensure proper exposure, make test shots before shooting important events.

A dv

an ce

d op

er at

io ns

92

Multiple flash shooting using cords

TTL multiple flash (not possible with digital SLRs and COOLPIX cameras compatible with i-TTL)

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Attach the master flash unit to the camera, turn the power on, and set the flash mode to TTL auto flash. A flash mode, in which Monitor preflashes are fired,

cannot be used.

3 When using either the optional TTL Multi-Flash Sync Cord SC-27,SC-26, SC-19 or SC-18, turn off all flash units before connecting the master flash unit to the remote flash units.

4 Turn on all remote flash units and set the flash mode on all remote flash unit to TTL auto flash.

5 Confirm the aperture and flash shooting distance as in normal TTL auto flash shooting, then shoot. See page 17 concerning the TTL auto flash mode. When the flash has fired at its maximum output and

underexposure may have occurred, the ready-light on the SB-800 blinks for approx. 3 sec. To compensate, use a wider aperture or move closer to the subject and reshoot.

FLASH

READY

93

Manual multiple flash

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Turn off the power and attach the master flash unit to the camera.

3 Connect the sync terminal on the master flash unit to the remote flash unit using the optional Sync Cord SC-11 or SC-15.

4 Turn on the power of all flash units and set the flash mode on all units to Manual flash. The flash output level can be adjusted on the SB-800,

SB-80DX, SB-28, and so forth, if necessary (p. 43). Repeating flash is not possible.

5 Confirm the aperture and flash shooting distance as in normal Manual flash shooting, then shoot. See page 46 for more information about the Manual

flash mode.

FLASH

READY

FLASH

READY

A dv

an ce

d op

er at

io ns

94

System chart for TTL multiple flash shooting using cords

SC-24

SB-21B

SB-21ASB-16A SB-17

SC-14

SB-11

SC-23

SB-14 SB-140

SB-16B

SB-15

SB-25 SB-26SB-24

SC-17/ 28

SB-27

AS-17

SB-29/29sSB-28/ 28DX

SB-22 SB-22sSB-20 SB-23 SB-30 SB-50DX

SB-800SB-80DX

Master flash unit

V-type Sync Cord Items marked on page 94 are connected to item on page 95.

Group I

Group V F-501/N2020, F-401s/N4004s, F-401/N4004 F-301/N2000

Group III F-601/N6006, F-601M/N6000

Group II F4-Series (with DW-20/DW-21)

F4-Series (with DA-20/DP-20) F65-Series/N65-Series F-801s/N8008s F-801/N8008 Pronea 600i/6i

Group VII F3-Series

Group IV F60-Series/N60 F50-Series/N50 F-401X/N5005

Group VI FM3A, FA, FE2, FG

Nikonos V

F5 (with DA-30/DP-30) F100 F90X/N90s F90-Series/N90 F80-Series/N80-Series F75-Series/N75-Series F70-Series/N70

F5 (with DW-30/DW-31)

F6

Film-based SLRs compatible with CLS

With the F6, it is not possible to use Auto FP High-Speed Sync and FV Lock operation at the same time.

Speedlights SB-11, SB-14, SB-140, and SB-21B cannot be used with the F-401/N4004 or F-401s/N4004s as either master or remote flash units.

95

A dv

an ce

d op

er at

io ns

SB-21B

SB-16B

SB-15 SB-22SB-20

SC-18/26 (1.5m) SC-19/27 (3m)

SC-18/26 SC-19/27

SC-18/26 SC-19/27

SB-25 SB-26 SB-28/28DX

SB-27

SB-24

SB-25 SB-26 SB-28/ 28DXSB-24SB-16B

AS-10

AS-10

AS-10

SB-16A

AS-11 AS-11

SB-17

SB-800

SB-22s

SB-29/29s

SB-30

SB-80DX

SB-11

SC-23

SB-14 SB-140

SB-800SB-29/29s SB-80DX

AS-11

SB-21A

Using SC-18/26 or SC-19/27, up to five flash units can be used for multiple flash photography at a total cable length of 10m (33 ft.).

Remote flash unit

96

Flash shooting with digital SLRs cameras using

Supplied with the SB-800, the Colored Gel Filter Set SJ-800 includes two filters: the FL-G1 for taking flash pictures under fluorescent light and the TN-A1 for use with incandescent/tungsten light. Colored Gel Filter Set SJ-1 is also available as an option (p. 112).

Using colored gel filters with digital cameras

Purpose Gel filter Adjust the cameras white balance to:

Balances the color of light from FL-G1 Fluorescent the flash to match that of fluorescent light

Balances the color of light from TN-A1 Incandescent the flash to match that of incandescent or tungsten light

Creates interesting effects by Optional color gel Flash changing the light from the filters flash to a different color

Balancing light from the flash With digital cameras, if you shoot flash pictures under fluorescent light with the cameras white balance set to Flash, the main subject illuminated by the flash will look normal. However, the background will come out green. To compensate, use the FL-G1 (green gel filter) to convert the light coming from the flash to the same color as fluorescent light, then adjust the cameras white balance to Fluorescent. Follow a similar procedure when shooting flash pictures under incandescent/tungsten illumination using the TN-A1 filter. In this case, set the white balance to Incandescent. Available with digital cameras featuring white balance. You cannot set the white balance

on the SB-800. Choose an appropriate white balance setting on your digital camera. For more details, see your cameras instruction manual.

When using tungsten film with a film-based camera, use the TN-A1 (for incandescent/tungsten light) filter for more effective results.

vNotes on using colored gel filters These filters are consumable items. When they extremely fade in color or deteriorate,

purchase optional Colored Gel Filter Set SJ-1. Colored gel filters may become deformed due to the heat generated from the flash

head. However, this will not affect their performance. When taking pictures using repeating flash, do not use these filters, because they may become deformed quickly due to the heat.

There is no difference between the front and back of colored gel filters. Even though they may be curled, this will not affect their performance. Likewise, scratches on these filters will have no effect on performance.

The amount of exposure compensation printed on each filter is provided as a guide only. Be sure to make test shots to determine the actual amount of compensation required.

To remove dust or dirt, wipe the filter lightly with a soft, clean cloth.

97

colored gel filters

How to use colored gels

1 Fold the colored gel filter securely on the line.

2 Insert the colored gel filter between the wide-flash adapter and the flash head.

3 Adjust the white balance setting on your digital camera, then shoot.

u Optional Colored Gel Filter Set SJ-1 The optional Colored Gel Filter Set SJ-1 contains a total of 20 filters in 8 models of colored gels for balancing the color of light or adding specific colors to the scene using a Speedlight (p. 112). FL-G1 (for fluorescent light) FL-G2 (for fluorescent light) TN-A1 (for incandescent/tungsten light) TN-A2 (for incandescent/tungsten light) BLUE YELLOW RED AMBER With the last four filters, adjust your digital cameras white balance (if available) to

Flash for the most effective results.

SHOOTING MENU White bal.

Auto Incandescent Fluorescent Direct sunlight Flash Cloudy Shade

A dv

an ce

d op

er at

io ns

98

Bounce flash operation

With the SB-800 mounted on your cameras hot shoe, you can tilt or rotate the flash head to bounce the light off the ceiling or walls. This is a good technique to use when shooting indoors, because you get more natural-looking pictures of people with softer shadows. Also, you can soften the shadows even more by using the Nikon Diffusion Dome.

Bounce flash Normal flash

Shooting data: Shooting data: Camera: D2H Camera: D2H Focal length: 60mm Focal length: 60mm Speedlight: SB-800 set to D Speedlight: SB-800 set to D Aperture: f/8 Aperture: f/9 Shooting distance: Approx. 4m (13.1 ft.) Shooting distance: Approx. 4m (13.1 ft.)

For more details on the above example, see the separate booklet, A collection of example photos.

Tilting the flash head For effective bounce flash off the ceiling, tilt the flash head up at least 50. Also, make sure that the light from the flash head does not directly illuminate the subject. Optimum results are obtained when the

flash head is positioned 12m (3.36.6 ft.) from the reflecting surface.

90

50

99

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Set the cameras metering system to Matrix Metering Y or Center-Weighted Metering W.

3 Set the flash mode to TTL or Auto Aperture or Non-TTL auto flash.

4 Set the cameras aperture. Refer to page 100 for setting the aperture.

5 Adjust the flash head.

6 Make sure that the ready-light is on, then shoot. When the flash has fired at its maximum output and

underexposure may have occurred, the ready-light on the SB-800 blinks for approx. 3 sec. To compensate, use a wider aperture or move closer to the subject and reshoot.

A dv

an ce

d op

er at

io ns

100

Bounce flash operation

Setting the aperture In bounce flash, there is a light loss of 23 stops when compared with normal flash photography. Therefore, you should use a wider aperture. When the flash head is adjusted to other than the horizontal/front position, the flash shooting distance range indicator on the SB-800 disappears. To ensure correct exposure, first confirm the flash shooting distance range and aperture with the flash head in the normal position. Next, set this aperture on the camera, then adjust the flash head to the appropriate bounce position. In Non-TTL auto flash operation, set the same aperture on the SB-800.

Setting the flash head As shown in the illustrations, tilt or rotate the SB-800s flash head by holding down the flash head tilting/rotating lock release button and adjusting the flash head to match the shooing environment or your creative preferences.

Flash head tilting and rotating angles The SB-800s flash head tilts up 90 and down 7, and rotates horizontally 180 to the left and 90 to the right. Set the flash head at a click stop at the angles shown. When taking close-up pictures with flash, tilt the flash

head down to the 7 position (p. 102).

Choosing the reflecting surface In color photography, select white or highly reflective surfaces to bounce the light off of. Otherwise, your pictures will come out with an unnatural color cast similar to that of the reflecting surface.

0 7

90 75 60

45

0 30

60

90

12 0

150 180

90 60

30

101

u Using the built-in bounce card In bounce flash photography, use the SB-800s built-in bounce card to create a highlight in the subjects eyes, making the eyes look more vibrant. As shown in the illustrations, pull out the wide-flash adapter and while holding the

bounce card, slide the wide-flash adapter back into place inside the flash head. Tilt the flash head up 90 to use this feature most effectively.

u Shooting with the Nikon Diffusion Dome By attaching the provided Nikon Diffusion Dome over the flash head, you can diffuse the light even more when doing bounce flash, creating extremely soft light with virtually no shadows. With the camera in either the horizontal or vertical position, you get the same effect. Good results are generally obtained when the flash head is tilted up 60. Use of the built-in wide-flash adapter in conjunction with the Nikon Diffusion Dome

results in the maximum amount of diffused light (p. 104).

Nikon Diffusion Dome attached Nikon Diffusion Dome not attached

Attach the Nikon Diffusion Dome as shown in the illustration. The zoom-head position is automatically set

at 14mm.

90 50

A dv

an ce

d op

er at

io ns

102

Close-up flash operation

When the built-in wide-flash adapter is used, close-up flash shooting can be performed. The built-in wide-flash adapter diffuses the light from the flash to soften shadows. When the SB-800 is used off-camera, you can take more natural-looking close-up pictures. Be sure to use the wide-flash adapter when taking close-up flash photographs. Be careful when using a long lens that the light from the flash is not obstructed by the

lens barrel. Vignetting may occur in close-up flash photography due to the lighting situation, lens in

use, focal length setting, etc. Therefore, make test shots before shooting an important assignment.

Flash shooting with two flash units Flash shooting with one (light bounced from the side and top) camera-mounted flash unit

Shooting data: Shooting data: Camera: D2H Camera: D2H Focal length: 105mm Focal length: 105mm Master flash unit: SB-800 set to D Master flash unit: SB-800 set to D Remote flash unit: SB-800 set to D Aperture: f/10 Aperture: f/22 Shooting distance: Approx. 1m (3.3 ft.) Shooting distance: Approx. 1m (3.3 ft.)

Example of close-up shooting with two flash units Illumination from the side and top provided by two flash units emphasizes the small subjects contours. Bounced light from the side softens the shadows.

For more details on the above example, see the separate booklet, A collection of example photos.

From the top

Remote flash unit

Master flash unit

Use either the SC-29, SC-28 or SC-17.

103

1 Set the cameras exposure mode to Aperture- Priority Auto (A) or Manual (M).

2 Set the cameras metering system to Matrix Metering Y or Center-Weighted Metering W.

3 Set the SB-800s flash mode to TTL auto flash.

4 Position the built-in wide-flash adapter over the flash head. Press the c or d button to adjust the zoom-head position to 14mm or 17mm.

5 Tilt the flash head down to 7. When the SB-800 is attached to the camera and used

as the only flash unit, this position is recommended to ensure sufficient illumination of the lower portion of the subject in close-up photography.

The dotted line below the underbar appears when the flash head is tilted down to this position.

6 Confirm that the ready-light is on, then shoot. When the flash has fired at its maximum output and

underexposure may have occurred, the ready-light on the SB-800 blinks for approx. 3 sec. To compensate, use a wider aperture or move closer to the subject and reshoot.

7

A dv

an ce

d op

er at

io ns

104

Close-up flash operation

Setting the built-in wide-flash adapter and adjusting the zoom-head position

1 Slowly pull out the wide-flash adapter all the way, and position it over the flash head. Then slide the bounce card back into place inside the flash head.

2 Press the c or d button to adjust the zoom head position to 14mm or 17mm. When the wide-flash adapter is set on the flash head,

the power zoom function becomes inactive and the zoom-head position is adjusted to 14mm or 17mm. To adjust the zoom-head position, go to the Custom Settings Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally (p. 67).

To slide the wide-flash adapter back into place, lift it and push it into the flash head as far as it will go.

Setting the aperture Calculate the aperture by using this equation and table. To ensure the correct exposure, use an aperture smaller than the one obtained from the equation.

ISO sensitivity 25 50 100 200 400 800 1000 Coefficient (m/ft) 1.4/4.6 2/6.6 2/6.6 4/13 4/13 5.6/18 5.6/18

f/stop Coefficient Flash-to-subject distance

For example, at an ISO sensitivity of 100 with a subject 0.5m (1.6 ft.) away and the wide-flash adapter in place, the suggested aperture is:

f/stop 2 0.5 = 4 (in meters) f/stop 6.6 1.6 = approx. 4 (in feet)

Therefore, you should use at least f/4 or an even smaller aperture, such as f/5.6 or f/8.

105

u When shooting subjects closer than 0.6m (2 ft.) With the SB-800 attached to the camera, sufficient illumination of the subject cannot be obtained. In this case, use the SB-800 off-camera by attaching the optional TTL Remote Cord as shown below.

In Do flash operation where Monitor Preflashes are fired, when the SB-800 is used with D/G-type CPU lenses, you may not be able to get the correct exposure, because distance information from the lens is used. In this case, position the camera (A) and the SB-800 (B) at equal distances from the subject.

For F5 cameras with the High-Magnification Finder DW-30 or DW-31, or F4 cameras with the High-Magnification Finder DW-20 or DW-21, use the optional TTL Remote Cord SC-24 instead of the SC-17.

A

B

A dv

an ce

d op

er at

io ns

Use either the SC-29, SC-28 or SC-17.

106

The farthest flash shooting distance cannot be read on the SB-800s LCD panel. In this case, use the guide number table and equation for calculating this distance, according to each zoom-head position.

D (farthest flash shooting distance) = Guide number f/stop (aperture)

Guide number (m/ft.) in the 1/300 TTL High-Speed Flash sync mode

1 With the Nikon Diffusion Dome attached and the wide-flash adapter in place

2 With the Nikon Diffusion Dome attached 3 With the wide-flash adapter in place

For example, when shooting with an ISO sensitivity of 100, at a 35mm zoom-head position and an aperture of f/5.6:

D = 14 5.6 (f/stop) = 2.5 (in meters) (farthest flash shooting distance)

D = 46 5.6 (f/stop) = 8.2 (in feet) (farthest flash shooting distance)

Flash shooting in the 1/300 TTL High-Speed Flash sync mode (F5 only)

ISO Zoom-head position (mm) sensitivity 1 2 143 173 24 28 35 50 70 85 105

25 2.5/8 3/10 3.5/11 3.5/11 5.5/18 6/20 7/23 8/26 9/30 9.5/31 10/33 50 3.6/12 4.3/14 5/16 5/16 7.8/26 8.5/28 9.9/32 11.4/37 12.8/42 13.5/44 14.2/47

100 5/16 6/20 7/23 7/23 11/36 12/39 14/46 16/52 18/59 19/62 20/66 200 7/23 8.4/28 9.8/32 9.8/32 15.4/51 16.8/55 19.6/64 22.4/73 25.2/83 26.6/87 28/92 400 10/33 12/39 14/46 14/46 22/72 24/79 28/92 32/105 36/118 38/125 40/131 800 14/46 16.8/55 19.6/64 19.6/64 30.8/101 33.6/110 39.2/129 44.8/147 50.4/165 53.2/174 56/184

Reference information

Optional accessories, Troubleshooting, Speedlight care, Specifications, etc. are presented here.

108

TTL auto flash modes available with the SB-800

The available types of TTL auto flash vary, depending on the camera/lens/ exposure mode/metering system in use. The following tables show the SB-800s TTL mode indicators and the corresponding ones used in the instruction manuals of Speedlights featuring no CLS when the flash unit is used with various cameras not compatible with CLS. Refer to your cameras instruction manual for specific information on camera settings

and functions.

Exposure mode P : Programmed Auto S : Shutter-Priority Auto A : Aperture-Priority Auto M : Manual

Metering system Y : Matrix W : Center-Weighted X : Spot

TTL/D-TTL auto flash mode D E : Automatic Balanced Fill-Flash with

TTL Multi Sensor D F : Matrix Balanced Fill-Flash, Center-

Weighted Fill-Flash/Spot Fill-Flash D : Standard TTL Flash

C D E : Automatic Balanced Fill-Flash with TTL Multi Sensor for Digital SLRs

C D F : Center-Weighted Fill-Flash for Digital SLRs

C D : Standard TTL Flash for Digital SLRs

Camera TTL mode with no CLS

TTL mode Exposure Metering Lens mode system

F5 DE2 P/S/A/M YW CPU lens (D/G-type) F100 DE3 P/S/A/M YW CPU lens (except for D/G-type)

DF A/M W Non-CPU lens D P/S/A/M YWX CPU lens D A/M WX Non-CPU lens

F90X/N90s DE2 P/S/A/M YWX CPU lens (D/G-type) 1

F90-Series/ DE3 P/S/A/M YWX CPU lens (except for D/G-type) N90 DF A/M WX Non-CPU lens F70-Series/ D P/S/A/M YWX CPU lens1

N70 D A/M WX Non-CPU lens 1: The A and M exposure modes cannot be used with a G-type lens. 2: 3D Multi-Sensor Balanced Fill-Flash is set. 3: Multi-Sensor Balanced Fill-Flash is set.

Do

Do

Do D D

Do

Do

Do D D

I

Camera Group

D1-Series C D E 1 P/S/A/M YW CPU lens (D/G-type)

D100

C D E 2

1

2

P/S/A/M YW CPU lens (except for D/G-type) C D F A/M W Non-CPU lens C D P/S/A/M YWX CPU lens C D A/M WX Non-CPU lens

1: 3D Multi-Sensor Balanced Fill-Flash for Digital SLRs is set. 2: Multi-Sensor Balanced Fill-Flash for Digital SLRs is set.

Digital SLRs not compatible with CLS

C D E P/S/A/M YW CPU lens (D/G-type) C D E P/S/A/M YW CPU lens (except for D/G-type) C D P/S/A/M YWX CPU lens C D

Do Do

Do D D

Do

Do D D M WX Non-CPU lens

Cameras compatible with the TTL/D-TTL auto flash mode

109

R ef

er en

ce in

fo rm

at io

n

Camera TTL mode with no CLS

TTL mode Exposure Metering Lens mode system

F4-Series D F P/S/A/M Y CPU lens1

D F A/M Y Non-CPU lens2

D F 3 P/S/A/M W CPU lens1

D F 3 A/M W Non-CPU lens

D P/S/A/M YWX CPU lens1

D A/M YWX Non-CPU lens

1: The A and M exposure modes cannot be used with a G-type lens. 2: AI-S, AI, Series E lens only usable. 3: Center-Weighted Fill-Flash is set.

F65-Series/ D F P/S/A Y CPU lens N65-Series

D P/S/A/M YW CPU lens1

D M W Non-CPU lens2

1: Center-Weighted Metering is automatically set when the exposure mode is set to M. 2: The cameras exposure meter cannot be used. Set the aperture using the lens aperture ring.

F-801s/ D F P/S/A/M Y CPU lens1

N8008s D F 3 P/S/A/M WX CPU lens 1/2

F-801/ D F 3 A/M WX Non-CPU lens2

N8008 D P/S/A/M YWX CPU lens 1/2

D A/M WX Non-CPU lens2

1: The A and M exposure modes cannot be used with a G-type lens. 2: Spot Metering is not possible with the F-801/N8008. 3: Center-Weighted Fill-Flash/Spot Fill-Flash is set.

Pronea D F P/S/A/M Y CPU lens 600i/6i

D P/S/A/M YWX CPU lens

D M WX Non-CPU lens1

1: The cameras exposure meter cannot be used. Set the aperture using the lens aperture ring.

Do

Do

Do

Do

D

D

Do

D

D

Do

Do

Do

D

D

Do

D

D

II

I

Camera Group

F80-Series/ DE2 P/S/A/M YW CPU lens (D/G-type) N80-Series DE3 P/S/A/M YW CPU lens (Non-D/G-type AF)

D P/S/A/M YWX CPU lens D M WX Non-CPU lens 1

F75-Series/ DE2 P/S/A Y CPU lens (D/G-type) N75-Series DE3 P/S/A Y CPU lens (Non-D/G-type AF)

D P/S/A/M W CPU lens D

Do

Do

D

D

Do

Do

D

D M W Non-CPU lens 1: The cameras exposure meter cannot be used. Set the aperture using the lens aperture ring. 2: 3D Multi-Sensor Balanced Fill-Flash is set. 3: Multi-Sensor Balanced Fill-Flash is set.

1

110

TTL auto flash modes available with the SB-800

Camera TTL mode with no CLS

TTL mode Exposure Metering Lens mode system

F-601M/ D P/S Y CPU lens1

N6000 D P/S W CPU lens1

D A/M W Non-CPU lens1

D P/S YW CPU lens

D A/M W Non-CPU lens 1: Only D appears on the SB-800s LCD panel. Matrix Balanced Fill-Flash or Center-

Weighted Fill-Flash/Spot Fill-Flash is selected when F appears on the cameras LCD panel.

F60-Series/N60 D1 P/S/A Y CPU lens

F50-Series/N50 D2 M W CPU/non-CPU lens

F-401x/N5005

F-501/N2020 D3 P W CPU4/non-CPU lens5

F-301/N2000 D A/M W CPU4/non-CPU lens 1: Matrix Balanced Fill-Flash is set. 2: Center-Weighted Fill-Flash/Spot Fill-Flash is set. 3: Programmed TTL Auto Flash is set. 4: G-type Nikkor lenses cannot be used. Nikkor lenses

for F3AF usable. 5: AI-S, AI, Series E lenses only usable.

F-401s/N4004s D2 P/S Y CPU lens

F-401/N4004 D A/M YW CPU lens1

D M W Non-CPU lens 1: Center-Weighted Metering is automatically set when the exposure mode is set to M. 2: Programmed TTL Auto Flash is set.

FM3A D A/M W CPU (except G-type)/non-CPU lens

FA D P/A/M YW CPU (except G-type)/non-CPU lens1

FE2 D A/M W CPU (except G-type)/non-CPU lens1

FG D P/A/M W CPU (except G-type)/non-CPU lens1

Nikonos V D A/M W CPU (except G-type)/non-CPU lens1/2

F3-Series D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D

D A/M W CPU (except G-type)/non-CPU lens3

1: Standard TTL Flash is not possible if the shutter speed is set to M250 or B (bulb) for the FA, FE2, and M90 for the FG and Nikonos V cameras.

2: An optional sync cord for land use is required. 3: Optional TTL Unit Coupler AS-17 is required.

VI

IV

V

Camera Group

F-601/ D P/S/A/M Y CPU lens (except for G-type)1

N6006 D P/S/A/M WX CPU lens (except for G-type)1

D A/M WX Non-CPU lens1

D P/S/A/M YWX CPU lens (except for G-type)2

D

D

D

D

D

D A/M WX Non-CPU lens2

1: Only D appears on the SB-800s LCD panel. Matrix Balanced Fill-Flash or Center- Weighted Fill-Flash/Spot Fill-Flash is selected when F appears on the cameras LCD panel.

2: Center-Weighted Metering is automatically set when the exposure mode is set to M.III

111

Optional accessories

R ef

er en

ce in

fo rm

at io

n

Accessories for multiple flash TTL Remote Cord SC-29/28/17 (approx. 1.5m or 4.9 ft) TTL Remote Cord SC-24 (approx. 1.5m or 4.9 ft) TTL Remote Cords SC-29/SC-28/SC-17/SC-24 provide TTL auto flash operation when the SB-800 is used off-camera. Their flash shoes come with one tripod socket and two TTL multiple flash terminals. The TTL Remote Cord SC-24 is for use with F5 cameras mounted with a High-Magnification Finder DW-30 or DW-31, or F4 cameras having a High- Magnification Finder DW-20 or DW-21. The SC-29 features an AF-assist illuminator function (The SC-29 is not equipped with a TTL multiple flash terminal.)

TTL Multi-Flash Sync Cord SC-26/18 (approx. 1.5 m or 4.9 ft) TTL Multi-Flash Sync Cord SC-27/19 (approx. 3 m or 9.8 ft) Multi-Flash Sync Cords SC-18/SC-19/SC-26/SC-27 are useful for connecting the SB-800 to the multiple flash terminal of the SC-28, SC-17 or AS-10 for TTL multiple flash operation.

TTL Multi-Flash Adapter AS-10 Use the Multi-Flash Adapter AS-10 when connecting more than three flash units together for TTL multiple flash operation, or if the remote flash units are not equipped with multiple flash terminals. The AS-10 comes with one tripod socket and three TTL multiple flash terminals.

Sync Cord SC-11 (approx. 25 cm or 9.8 in.) Sync Cord SC-15 (approx. 1 m or 3.3 ft) Sync Cords SC-11 and SC-15 are handy when you want to use the SB-800 off-camera or for use with cameras not having accessory shoes. These cords also allow you to perform multiple flash operation in the Manual mode.

Sync Terminal Adapter AS-15 The Sync Terminal Adapter AS-15 is necessary when connecting the SB-800 to cameras not having a sync terminal.

Wireless Slave Flash Controller SU-4 Useful for multiple flash photography, the SU-4 features a built-in, movable light sensor and an accessory shoe for attachment of a remote flash unit. The SU-4s light sensor not only triggers the remote unit to fire in sync with the master unit, but controls the flash duration of the remote unit to provide wireless TTL, Non-TTL, or Manual operation.

SC-29

TTL Flash Unit Coupler AS-17 for F3-Series cameras Dedicated adapter for F3-Series cameras providing TTL flash operation with Nikon Speedlights such as the SB-800 featuring an ISO-type mounting foot (not designed for the F3).

Bracket SK-7 A metal plate with attachment screws allowing the camera and Speedlight to be positioned side by side. Use the optional TTL Multi-Flash Adapter AS-10 to attach the SB-800 to Bracket SK-7.

Multi-Flash Bracket Unit SK-E900 (One AS-E900 Multi-Flash Adapter is included with the SK-E900) Multi-Flash Adapter AS-E900 The SB-800 can be used as a multiple flash unit with Nikon COOLPIX 900-series digital cameras by attaching the COOLPIX to Multi-Flash Bracket Unit SK-E900 and connecting the SB-800 to the multi-flash terminal of the COOLPIX using the Multi-Flash Adapter AS-E900 (p. 34).

Other accessories

Speedlight Stand AS-19 Same as that provided with this SB-800.

Colored Gel Filter Set SJ-1 A total of 20 filters in 8 models are provided. Colored gel filters are consumable items and subject to a gradual deterioration in color due to the heat generated when the flash fires. Therefore, it is recommended to check and replace these filters when necessary.

112

Optional accessories

113

R ef

er en

ce in

fo rm

at io

n

Using external power sources Connecting to an external power source To use an external power source, remove the cover and connect its power cord to the SB-800s external power source terminal. Do not use the power cord SC-16 when connecting the

SB-800 to the Nikon DC Unit SD-7; use the SC-16A instead. Using external power sources made by another

manufacturer is not recommended.

Specifications

1 With AA-type alkaline-manganese batteries in the SB-800. 2 With the same type of batteries in both the external power source and the SB-800. 3 When fired at an interval of 120 seconds. The above data may vary due to variations in performance or whether fresh or old

batteries are used. In rare cases, when firing the modeling illuminator with the SD-8A or SK-6/SK-6A

attached, the SB-800 may be powered by its own batteries, and the external power source does not operate. This is not a malfunction.

Power Bracket Unit SK-6/SK-6A

Nikon High-Performance Battery Pack SD-8A

Nikon DC Unit SD-7

External power source

DC Unit SD-71

High- Performance Battery Pack SD-8A2

Power Bracket Unit SK-6/SK-6A1

C-type alkaline-manganese (x 6) AA-type alkaline-manganese (x 6) AA-type NiCd (1000mAh) (x 6)

AA-type Ni-MH (2000mA) (x 6) AA-type lithium (x 6)3

AA-type alkaline-manganese (x 4) AA-type NiCd (1000mAh) (x 4)

AA-type Ni-MH (2000mA) (x 4) AA-type lithium (x 4)3

2.5 sec. 2.5 sec. 2 sec.

2 sec. 3.5 sec. 3 sec. 2.5 sec.

2.5 sec. 3.5 sec.

350 times/2.5-30 sec. 320 times/2.5-30 sec. 190 times/2-30 sec.

AA-type Nickel (x 6) 2.5 sec. 380 times/2.5-30 sec. 300 times/2-30 sec. 310 times/3.5-30 sec. 230 times/3-30 sec. 150 times/2.5-30 sec.

AA-type Nickel (x 4) 3 sec. 280 times/3-30 sec. 230 times/2.5-30 sec. 260 times/3.5-30 sec.

Battery type required Min. recycling time (approx.)

Min. number of flashes/recycling time (approx.)

WARNING Never use thinner, benzene, or other active agents for cleaning the Speedlight, as this may damage the Speedlight or cause it to catch on fire. Using these agents may also impair your health.

Cleaning Use a blower brush to remove dirt and dust from the SB-800 and clean it with a soft,

clean cloth. After using the SB-800 near saltwater, wipe the flash unit with a soft, clean cloth moistened slightly with plain water to remove the salt, then dry it using a dry cloth.

On rare occasions, the LCD may turn on or turn dark, due to static electricity. This is not a malfunction. The display will soon return to normal.

Do not drop the SB-800 or hit it against a hard surface, as this may damage its precision mechanisms. Do not apply strong pressure to the LCD panel.

Storage Store the SB-800 in a cool, dry place to prevent malfunctions due to high humidity, as

well as the growth of mold or mildew. Keep the SB-800 away from chemicals such as camphor or naphthalene. Avoid

exposing the SB-800 to magnetic waves from TVs or radios. Do not use or leave the SB-800 in locations subject to high temperatures such as those

encountered near a heater or stove, as this may cause damage. When not using the SB-800 for more than two weeks, be sure to remove the batteries to

prevent malfunctions due to battery leakage. Take the SB-800 out once a month, insert the batteries, and fire the unit several times to

reform the capacitor. When the SB-800 is stored together with a desiccant, change the desiccant occasionally

since it does not absorb moisture effectively after a while.

Operating location An extreme temperature change can cause condensation inside the SB-800. When

taking the SB-800 to a very hot place from a very cold place or vice versa, place it inside an airtight container such as plastic bag. Leave it inside for a while, then expose the SB-800 gradually to the outside temperature.

Avoid exposing the SB-800 to strong magnetism or radio waves from TVs or high- voltage power transmission towers, as this may cause it to malfunction.

114

Tips on Speedlight care

115

Notes on batteries

R ef

er en

ce in

fo rm

at io

n

Usable batteries Use four (or five) AA-type batteries (1.5V or lower) of any of the following types. High-power manganese batteries are not recommended. Using the Quick Recycling Battery Pack SD-800 (p. 64) or an external power source

(p. 113) increases the number of flashes and provides faster recycling times.

Alkaline-manganese (1.5V)/Nickel (1.5V) batteries Non-rechargeable. Never attempt to charge these batteries in a battery charger. Otherwise, they may explode. Lithium (1.5V) batteries Non-rechargeable. Never attempt to charge these batteries in a battery charger. Otherwise, they may explode. Depending on battery specifications, when these batteries become hot, the safety

circuits are activated, cutting off power. This often occurs when the flash unit is operated in the repeating flash mode. Battery power will recover when the temperature returns to normal.

NiCd battery (rechargeable, 1.2V) /Ni-MH (rechargeable, 1.2V) Rechargeable. Before recharging the batteries, be sure to read the instruction manuals for your batteries and battery charger for detailed information on how to handle and recharge the batteries.

Recycling rechargeable

NiCd batteries

Notes on handling batteries Because flash consumes a large amount of battery power, rechargeable batteries may

not operate properly before reaching the end of their stated lifespan or the number of charging/discharging as specified by the battery manufacturer.

When replacing batteries, replace all four (or five) batteries at the same time. Do not mix battery types or brands or use old with new batteries.

When installing batteries, turn off the power of the Speedlight and never reverse the polarity of the batteries.

If the battery terminals become soiled, remove dirt and smudges before use, as this may cause a malfunction.

Battery power tends to weaken as the temperature drops. It also gradually decreases when batteries are not used for a long time and recovers after a short break following intensive use. Be sure to check battery power and replace the batteries with fresh ones, if you notice any delays in the recycling time.

Do not store batteries in locations subject to high temperatures and high humidity.

To protect the earths environment, do not dispose of used rechargeable batteries yourself. Instead, take these batteries to your nearest recycling center.

116

Troubleshooting

If a warning indication appears on the SB-800s LCD panel or inside the cameras viewfinder, use the following chart to determine the cause of the problem before you take your Speedlight to a Nikon service center for repair.

Problems with the SB-800

Problem

The power cannot be turned on. The ready-light does not light up.

The power turns off automatically. A strange sound can be heard caused by the flash head zooming back and forth even when the SB-800 is turned off. The flash shooting distance range does not appear. No D, or o indicator appears in TTL auto flash mode.

The zoom-head position cannot be adjusted to other than 14mm or 17mm.

The SB-800 does not work when control buttons (a button, e/f button, or c/d button) and g button are pressed.

The SB-800 does not fire.

Cause

The batteries are not correctly installed. nBattery power is weak. nThe standby function is activated

and operating.

The batteries are extremely exhausted.

The batteries are extremely exhausted.

The flash head is adjusted to other than the horizontal/front or down -7 position. The cameras exposure mode or metering system is not correctly set or a non-CPU lens is mounted. The built-in wide-flash adapter is in use or the Nikon Diffusion Dome is attached.

Control buttons are locked.

Canceling flash firing is activated in the Custom settings mode.

Ref. page p. 18 p. 19 p. 21

p. 19

p. 19

p. 23

p. 108

p. 12

p. 67

p. 101 p. 96

117

R ef

er en

ce in

fo rm

at io

n

If the built-in wide-flash adapter is broken off accidentally If the wide-flash adapter is subjected to a strong impact while set on the flash head, it may be broken off. In this case, visit your nearest authorized Nikon service center for repair. When the wide-flash adapter is broken off, it is no longer possible to set the zoom-head

position to other than 14mm or 17mm. To adjust the zoom-head position, go to the Custom Settings Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally (p. 67).

Warning indications in the SB-800

Problem

The ready-light blinks for 3 sec. after firing. The underexposure indicator blinks and the amount of underexposure is displayed, depending on the camera in use. The dotted line below the underbar appears.

Three beeps sound during wireless multiple flash shooting.

Cause

Underexposure may have occurred.

The flash head is tilted down 7.

The flash has fired at its maximum output and under exposure may have occurred.

Ref. page

p. 33

p. 23

p. 89

The aperture indicator displays FEE and the shutter cannot be released.

The aperture on the lens is not set at its minimum.

118

Troubleshooting

Ready-light warning inside the cameras viewfinder

Note The SB-800 incorporates a microcomputer to control flash operations. In rare cases, the SB-800 may not work properly even after fresh batteries are properly installed. If this happens, replace the batteries while the SB-800s power is turned on.

Warning Batteries should not be exposed to excessive heat such as strong sunshine, a fire,

or the like. Dry batteries should never be recharged in a battery charger. Do not expose the SB-800 to water as this may result in an electric shock or cause

the unit to catch on fire.

Cameras in Groups I (except for F70-Series/N70) to VI and Digital SLRs cameras

Problem

The ready-light blinks when pressing the shutter release button slightly in the TTL auto flash mode. Cameras in Groups V and VI The ready-light blinks when the power is turned on in TTL auto flash mode.

The ready-light blinks in the TTL auto flash mode.

The ready-light blinks.

The ready-light blinks when the flash mode is set to TTL auto flash.

Cause

The SB-800 is not correctly attached to the camera.

The ISO sensitivity set on the camera is higher than the available range of the Speedlight.

The ISO sensitivity set on the camera is higher or lower than the available range for the FA camera.

for the FA camera.

The shutter speed is set to M90, M250, or B (bulb).

The shutter speed set is faster than the flash sync speed.

The SB-800s flash mode is set to TTL auto flash.

Ref. page

p. 22

p. 110

p. 110

Cameras in Group VI

FM3A, New FM2 cameras

New FM2, F55-Series/N55-Series cameras.

119

About the LCD panel

R ef

er en

ce in

fo rm

at io

n

Characteristics of the LCD panel Due to the directional characteristics of LCDs, the LCD display is difficult to read when

viewed from above. However, the display can be seen clearly from a somewhat lower angle.

The LCD display becomes darker at high temperatures (approx. 60C/140F), but returns to normal at normal temperatures (20C/68F).

The LCDs response time slows down at low temperatures (approx. 5C/41F and below), but returns to normal at normal temperatures (20C/68F).

Using the SB-800 in dim light Press any button on the SB-800 to turn the illuminator on (when the SB-800 power is on), and it will remain lit for approx. 16 seconds. To cancel the LCD panel illumination, go to the Custom settings mode (p. 67) and

set it off. Even if the LCD panel illuminator is set to OFF, the SB-800s LCD panel illuminator turns

on when the cameras LCD panel illuminator is turned on. The LCD panel illuminator also lights up when the Custom settings mode is displayed.

Adjusting the LCD panel brightness The brightness of the LCD panel can be adjusted in the Custom settings mode for easier reading (p. 67).

1 Select LCD in the Custom settings mode, then press the g button.

2 Press the c or d button to highlight the desired brightness level. Available brightness levels are graphically

displayed in 9 steps on the LCD panel.

120

Specifications

Electronic construction

Automatic Insulated Gate Bipolar Transistor (IGBT) and series circuitry

Guide number (at 35mm zoom-head position, 20C/68F)

38/125 (ISO 100, m/ft), 53/174 (ISO 200, m/ft)

Flash exposure control set on the camera

Slow-sync, Red-eye reduction, Red-eye reduction in slow-sync, Rear-curtain sync flash, Auto FP High-Speed sync, FV Lock flash

Flash shooting distance range (TTL auto flash/ Auto Aperture flash/ Non-TTL auto flash)

0.6m to 20m (2 to 66 ft.) (varies depending on the ISO sensitivity, zoom-head position, and lens aperture in use)

Flash exposure control Indicator Available flash mode D i-TTL mode Cameras compatible with CLS, COOLPIX cameras

compatible with i-TTL

No limitation Except D1X and D1H digital cameras

Except COOLPIX cameras compatible with i-TTL

Digital SLRs not compatible with CLS Cameras in Groups I to VI (film based cameras) Cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to IV (No o appears with cameras in Groups III to IV) Cameras compatible with CLS, digital SLRs not compatible with CLS, cameras in Groups I to II and COOLPIX cameras compatible with i-TTL

D D-TTL mode D TTL (film based) mode o (appears with D)

Balanced Fill-Flash

B Auto Aperture flash

A Non-TTL auto flash p Distance-priority

manual flash

q Repeating flash No limitationG Manual flash

Usable camera

Available multiple flash Usable camera

Advanced Wireless Lighting Cameras compatible with CLS

SU-4 type wireless multiple flash No limitation Multiple flash shooting using cords No limitation

Other available functions Test firing, Monitor Preflashes, AF-assist illuminator, and Modeling illuminator

A variety of flash operations are available with compatible cameras: i-TTL mode, Advanced Wireless Lighting, FV Lock flash, Flash color information communication, Auto FP High-Speed sync, and Wide-area AF-Assist Illuminator

Nikon Creative Lighting System

Multiple flash operation

121

R ef

er en

ce in

fo rm

at io

n

Bounce capability

Flash head tilts down to 7 or up to 90 with click-stops at 7, 0, 45, 60, 75, 90; flash head rotates horizontally 180 to the left or 90 to the right with click-stops at 0, 30, 60, 90, 120, 150, 180

ON/OFF button nPress the b button for approx. 0.3 sec. to turn the SB-800 on or off. Standby function can be set. n

Power source/ min. recycling time/no. of flashes (at M1/1 output)

Four (or five) AA-type penlight batteries (1.5V or lower) of any of these types: Alkaline-manganese (1.5V), Lithium (1.5V), Nickel (1.5V), NiCd (rechargeable, 1.2V), or Ni-MH (rechargeable, 1.2V)

* With fresh batteries. M1/1 output without use of AF-assist illuminator, zoom operation, and LCD panel illuminator.

n

Batteries Min. recycling time (approx.)*

Number of batteries

Min. number of flashes/ recycling time*

Alkaline- manganese

6.0 sec.x4 x5 x4 x5 x4

130/630 sec.

Lithium 5.0 sec. 130/530 sec.

Nickel

7.5 sec. 170/7.530 sec.

NiCd (1000 mAh) (rechargeable)

7.5 sec. 190/7.530 sec.

Ni-MH (2000 mA) (rechargeable)

6.0 sec. 140/630 sec. x5 5.0 sec. 140/530 sec. x4 4.0 sec. 90/430 sec. x5 3.5 sec. 90/3.530 sec. x4 4.0 sec. 150/430 sec. x5 2.9 sec. 150/2.930 sec.

Angle of coverage

Variable in 7 steps, plus three steps with wide-flash adapter and Nikon Diffusion Dome

1 With the Nikon Diffusion Dome attached With the built-in wide-flash adapter set2

Zoom-head position

Angle of coverage Vertical Horizontal

14mm 14mm 110 120 14mm 14mm 110 120 17mm 17mm 100 110

24mm 24mm 60 78 28mm 28mm 53 70 35mm 35mm 45 60 50mm 50mm 34 46 70mm 70mm 26 36 85mm 85mm 23 31

105mm 105mm 20 27

1

2

2

122

Specifications

Other functions

Recalling the underexposure value in the TTL auto flash mode, Resetting the settings, Button lock

Built-in wide- Allows SB-800 to be used with 14mm or 17mm lens flash adapter Dimensions Approx. 70.5 x 129.5 x 93.0mm (2.8 x 5.1 x 3.7 in.) (W x H x D)

Mounting foot Provides secure attachment of SB-800 to cameras accessory shoe using locking plate and mount pin to prevent accidental detachment.

lock lever

Flash output level compensation

3.0 to +3.0 EV in increments of 1/3 steps in the TTL auto flash, Auto Aperture flash modes and Distance-priority manual flash

Custom settings

By pressing the g and ef, c or d buttons, the following custom settings are possible: ISO sensitivity, Wireless flash auto, Sound monitor in the wireless flash mode, Non-TTL auto flash, Standby function, Selecting the distance unit (m, ft.), Canceling power zoom function, Zoom-head position setting if the built-in wide-flash adapter is broken off accidentally, LCD panel illuminator, Brightness of the LCD panel, AF-assist illuminator, and canceling flash firing.

External power sources (optional)

Ready-light nLights up when the SB-800 is recycled and ready to fire. nBlinks for 3 sec. when flash fires at its maximum output, indicating

light may have been insufficient (in TTL Auto Flash, Auto Aperture B Flash and Non-TTL Auto Flash A operations)

Flash 1/1050 sec. at M1/1 (full) output duration 1/1100 sec. at M1/2 output (approx.) 1/2700 sec. at M1/4 output

1/5900 sec. at M1/8 output 1/10900 sec. at M1/16 output 1/17800 sec. at M1/32 output 1/32300 sec. at M1/64 output 1/41600 sec. at M1/128 output

External power source Battery type DC Unit SD-7 Six C-type alkaline-manganese High-Performance Battery Six AA-type alkaline-manganese Pack SD-8A Power Bracket Unit SK-6/SK-6A

Four AA-type alkaline-manganese

123

R ef

er en

ce in

fo rm

at io

n

Weight Approx. 350g (12.3 oz.) (without batteries) Accessories Quick Recycling Battery Pack SD-800, Speedlight Stand

AS-19, Colored Gel Filter Set SJ-800, Nikon Diffusion Dome SW-10H, External power source terminal cap, Soft Case SS-800

supplied

These performance specifications are applicable when fresh batteries are used at normal temperatures (20 C/68 F). Specifications and design are subject to change without notice.

124

Symbol e/f button………………………………………12 i-TTL mode ………………………………………..36

A AF-ILL……………………………………………….62 AF-ILL ONLY………………………………………62 Accessories……………………………………..111 Advanced Wireless Lighting ………………..76 Aperture-priority auto exposure (A) ………29 Auto Aperture flash …………………………….38 Auto FP High-Speed sync……………………60 Automatic Balanced Fill-Flash ……………..37

B Batteries …………………………………….18, 115 Beyond the flash shooting distance

range warning………………………………..45 Bounce flash operation ……………………….98 Built-in wide-flash adapter …………………104 Button lock ………………………………………..12

C CLS…………………………………………………….5 COOLPIX…………………………………………..34 CPU Nikkor lenses ……………………………..16 Camera groups ……………………………………8 Canceling flash firing ………………………….67 Channel …………………………………………….78 Close-up flash operation……………………102 Colored gel filters ……………………………….96 Communication channel ……………………..77 Compatible with CLS ……………………………8 Continuous flash shooting……………………51 Control button quick reference …………….12 Control buttons…………………………………..12 Custom functions ……………………………….67

D D-TTL mode ………………………………………36 D-type Nikkor lenses…………………………..16 Default settings ……………………………………6 Digital SLRs not compatible with CLS …….8 Distance-priority manual flash ……………..44 Dotted line below the underbar ……………23

E Exposure compensation ……………………..54 Exposure mode ………………………………….28 External power source ………………………113

F FLASH button …………………………………….12 FV Lock flash……………………………………..61 Flash Color Information

Communication………………………………..5 Flash head……………………………………….100 Flash head tilting/rotating lock

release button ………………………………..22 Flash modes………………………………………35 Flash output level ………………………….42, 48 Flash output level

compensation value………………………..56 Flash shooting distance range……………..31 Flash sync mode………………………………..32 Frequency …………………………………………48 Front-curtain sync ………………………………32

G G-type Nikkor lenses…………………………..16 Group …………………………………………………8 Guide number ……………………………………42

H Highlighted items ……………………………….15

Index

Refer to the Speedlight parts and their functions (p. 10) and Icons on the LCD panel (p. 13) for each part name and display indications.

125

I ISO sensitivity…………………………………….24 ISO sensitivity factors………………………….43 Icons…………………………………………………13

L LCD panel illuminator………………………..119 LCD panel ……………………………………….119

M MASTER ………………………………………15, 72 MODE button……………………………………..30 Manual exposure (M) mode…………………29 Manual flash ………………………………………46 Manual mode …………………………………….42 Master flash unit …………………………………72 Metering system…………………………………28 Minimum recycling time ………………………19 Modeling illuminator ……………………………66 Monitor Preflashes………………………………36 Mounting foot lock lever………………………22 Multi Selector……………………………………..12 Multiple flash operation……………………….72 Multiple flash shooting using cords ………90

N NO AF-ILL …………………………………………62 Nikon Creative Lighting System……………..5 Nikon Diffusion Dome………………………..101 Non-CPU lenses…………………………………16 Non-TTL auto flash……………………………..40 Non-TTL auto flash mode…………………….38 Number of flashes…………………………19, 48

O ON/OFF button …………………………………..12

P Power zoom function…………………………..26 Programmed auto (P)………………………….28

Q Quick Recycling Battery Pack ……………..64

R REMOTE……………………………………………72 Ready-light …………………………………..20, 33 Rear-curtain sync ……………………………….59 Red-eye reduction control……………………58 Red-eye reduction with slow-sync

flash ……………………………………………..58 Remote flash unit ……………………………….72 Repeating flash ………………………………….48 Reset ………………………………………………..12

S SU-4 type wireless multiple flash

shooting ………………………………………..84 Selecting the distance unit (m or ft.)……..70 Shutter-priority auto exposure (S) …………29 Slow-sync flash mode …………………………58 Soft Case…………………………………………….6 Sound monitor ……………………………………89 Speedlight Stand………………………………..75 Speedlight parts and their functions……..10 Standard TTL flash ……………………………..37 Standby function ………………………………..21 Supplied accessories……………………………6

T TTL mode ………………………………………….37 Test firing …………………………………………..20

U Underexposure value in the TTL

auto flash mode ……………………………..33 Using the built-in bounce card …………..101

W Wide-Area AF-Assist Illuminator ……….5, 62 Wireless flash mode……………………………69 Wireless master flash unit ……………………72 Wireless multiple flash shooting……………72 Wireless remote flash …………………..