Инструкция киа рио 2014 года

Thank you for choosing a Kia vehicle.

When you require service, remember that your Kia Dealer knows your vehicle best. Your dealer has factory-trained technicians, recommended special tools, genuine Kia replacement parts and is dedicated to your complete satisfaction.

Because subsequent owners require this important information as well, this publication should remain with the vehicle if it is sold.

This manual will familiarize you with operational, maintenance and safety information about your new vehicle. It is supplemented by a Warranty and Consumer Information manual that provides important information on all warranties regarding your vehicle.

We urge you to read these publications carefully and follow the recommendations to help assure enjoyable and safe operation of your new vehicle.

Kia offers a great variety of options, components and features for its various models. Therefore, some of the equipment described in this manual, along with the various illustrations, may not be applicable to your particular vehicle.

The information and specifications provided in this manual were accurate at the time of printing. Kia reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation. If you have questions, always check with your Kia dealer.

We assure you of our continuing interest in your motoring pleasure and satisfaction in your Kia vehicle.

© 2014 Kia Canada Inc.

All rights reserved. Reproduction by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Kia Canada Inc..

Printed in Korea

Introduction

HOW TO USE THIS MANUAL

We want to help you get the greatest possible driving pleasure from your vehicle. Your Owner’s Manual can assist you in many ways. We strongly recommend that you read the entire manual. In order to minimize the chance of death or injury, you must read the WARNING and CAUTION sections in the manual.

Illustrations complement the words in this manual to best explain how to enjoy your vehicle. By reading your manual, you will learn about features, important safety information, and driving tips under various road conditions.

The general layout of the manual is provided in the Table of Contents. Use the index when looking for a specific area or subject; it has an alphabetical listing of all information in your manual.

Sections: This manual has eight sections plus an index. Each section begins with a brief list of contents so you can tell at a glance if that section has the information you want.

You will find various types of safety instructions in this manual. These instructions were prepared to enhance your personal safety. Carefully read and follow ALL procedures and recommendations provided in these instructions.

WARNING

A WARNING indicates a situation in which harm, serious bodily injury or death could result if the warning is ignored.

CAUTION

A CAUTION indicates a situation in which damage to your vehicle could result if the caution is ignored.

NOTICE

ANOTICE indicates interesting or helpful information is being provided.

FUEL REQUIREMENTS

Your new Kia vehicle is designed to use only unleaded fuel having a pump octane number ((R+M)/2) of 87 (Research Octane Number 91) or higher.

Your new vehicle is designed to obtain maximum performance with UNLEADED FUEL, as well as minimize exhaust emissions and spark plug fouling.

Never add any fuel system cleaning agents to the fuel tank other than what has been specified. (Consult an authorized Kia dealer for details.)

WARNING — Refueling

•Do not «top off» after the nozzle automatically shuts off when refueling.

•Always check that the fuel cap is installed securely to prevent fuel spillage in the event of an accident.

NOTICE

Tighten the cap until it clicks one time, otherwise the fuel cap open warning indicator will illuminate.

Introduction

Introduction

VEHICLE BREAK-IN PROCESS

No special break-in period is needed. By following a few simple precautions for the first 1,000 km (600 miles) you may add to the performance, economy and life of your vehicle.

•Do not race the engine.

•While driving, keep your engine speed (rpm, or revolutions per minute) between 2,000 rpm and 4,000 rpm.

•Do not maintain a single speed for long periods of time, either fast or slow. Varying engine speed is needed to properly break-in the engine.

•Avoid hard stops, except in emergencies, to allow the brakes to seat properly.

•Don’t tow a trailer during the first 2,000 km (1,200 miles) of operation.

INDICATOR SYMBOLS ON THE INSTRUMENT CLUSTER

For more detailed explanations, refer to “Instrument cluster” in section 4.

Introduction

ESC indicator

ESC OFF indicator

Electric power steering (EPS) system warning light*

ECO ECO indicator*

Auto stop for ISG system indicator*

Low tire pressure telltale* /

TPMS malfunction indicator*

CRUISE Cruise control indicator*

Cruise SET indicator*

Fuel cap open warning indicator

* : if equipped

Safety features of your vehicle

SEAT

The actual seats in the vehicle may differ from the illustration.

Driver’s seat

(1)Forward and rearward

(2)Seatback angle

(3)Seat cushion height

(4)Seat warmer

(5)Headrest

Front passenger’s seat

(6)Forward and rearward

(7)Seatback angle

(8)Seat warmer

(9)Headrest

Rear seat

(10)Headrest

(11)Seatback folding

OUB032001K

WARNING — Loose objects

Do not place anything in the driver’s foot well or under the front seats. Loose objects in the driver’s foot area could interfere with the operation of the foot pedals.

WARNING — Uprighting seat

Do not press the release lever on a manual seatback without holding and controlling the seatback. The seatback will spring upright possibly impacting you or other passengers.

WARNING — Driver responsibility for passengers

The driver must advise the passenger to keep the seatback in an upright position whenever the vehicle is in motion. If a seat is reclined during an accident, the occupant’s hips may slide under the lap portion of the seat belt, applying great force to the unprotected abdomen.

WARNING— Seat cushion

Occupants should never sit on seat cushions. The passenger’s hips may slide under the lap portion of the seat belt during an accident or a sudden stop.

WARNING — Driver’s seat

•Never attempt to adjust the seat while the vehicle is moving. This could result in loss of control of your vehicle.

•Do not allow anything to interfere with the normal position of the seatback. Storing items against a seatback or in any other way interfering with proper locking of a seatback.

•Sit as far back as possible from the steering wheel while still maintaining comfortable control of your vehicle. A distance of at least 10″ from your chest to the steering wheel is recommended. Failure to do so can result in airbag inflation injuries to the driver.

Safety features of your vehicle

WARNING — Seat

adjustment

•Do not adjust the seat while wearing seat belts. Moving the seat forward will cause strong pressure on the abdomen.

•Do not place your hand near the seat bottom or seat track while adjusting the seat. Your hand could get caught in the seat mechanism.

Safety features of your vehicle

OUB031002

Front seat adjustment

Forward and backward

To move the seat forward or backward:

1.Pull the seat slide adjustment lever up and hold it.

2.Slide the seat to the position you desire.

3.Release the lever and make sure the seat is locked in place.

Adjust the seat before driving, and make sure the seat is locked securely by trying to move forward and backward without using the lever. If the seat moves, it is not locked properly.

WARNING — Unexpected seat movement

After adjusting a manual seat, always check that it is locked by shifting your weight to the front and back. Sudden or unexpected movement of the driver’s seat could cause you to lose control of the vehicle.

OUB031003

Seatback angle

To recline the seatback:

1. Lean forward slightly and lift up the seatback recline lever.

2. Carefully lean back on the seat and adjust the seatback of the seat to the position you desire.

3. Release the lever and make sure the seatback is locked in place. (The lever MUST return to its original position for the seatback to lock.)

OUB031004

Seat height (for driver’s seat) (if equipped)

To change the height of the seat, move the lever upwards or downwards.

•To lower the seat cushion, push down the lever several times.

•To raise the seat cushion, pull up the lever several times.

OUB031042N

Headrest

The driver’s and front passenger’s seats are equipped with a headrest for the occupant’s safety and comfort.

The headrest not only provides comfort for the driver and front passenger, but also helps protect the head and neck in the event of a collision.

For maximum effectiveness in case of an accident, the headrest should be adjusted so the middle of the headrest is at the same height of the center of gravity of an occupant’s head. Generally, the center of gravity of most people’s head is similar with the height of the top of their eyes. Also, adjust the headrest as close to your head as possible.

For this reason, the use of a cushion that holds the body away from the seatback is not recommended.

WARNING — Headrest

removal/adjustment

•Do not operate the vehicle with the headrests removed. Headrests can provide critical neck and head support in a crash.

•Do not adjust the headrest height while the vehicle is in motion. Driver may lose control of the vehicle.

OUB031007

Forward and backward adjustment

The headrest may be adjusted forward to 4 different positions by pulling the headrest forward to the desired detent. To adjust the headrest to it’s furthest backwards position, pull it fully forward to the farthest position and release it. Adjust the headrest so that it properly supports the head and neck.

OUB031005

Adjusting the height up and down

To raise the headrest, pull it up to the desired position (1). To lower the headrest, push and hold the release button (2) on the headrest support and lower the headrest to the desired position (3).

OUB034100

Removal and installation

To remove the headrest:

1.Recline the seatback (2) with the recline lever (1).

2.Raise headrest as far as it can go.

3.Press the headrest release button (3) while pulling the headrest up (4).

WARNING

NEVER allow anyone to ride in a seat with the headrest removed.

OUB034101

To reinstall the headrest :

1.Put the headrest poles (2) into the holes while pressing the release button (1).

2.Recline the seatback (4) with the recline lever (3).

3.Adjust the headrest to the appropriate height.

WARNING

Always make sure the headrest locks into position after reinstalling and adjusting it properly.

OUB031008

Seat warmer (if equipped)

The seat warmers are provided to warm the front seats during cold weather. With the ignition switch in the ON position, push either of the switches to warm the driver’s seat or the front passenger’s seat.

During mild weather or under conditions where the operation of the seat warmer is not needed, keep the switches in the OFF position.

With the seat warmer switch in the ON position, the heating system in the seat turns off or on automatically depending on the seat temperature.

CAUTION — Seat damage

•When cleaning the seats, do not use an organic solvent such as paint thinner, benzene, alcohol and gasoline. Doing so may damage the surface of the heater or seats.

•To prevent overheating the seat warmer, do not place anything on the seats that insulates against heat, such as blankets, cushions or seat covers while the seat warmer is in operation.

•Do not place heavy or sharp objects on seats equipped with seat warmers. Damage to the seat warming components could occur.

WARNING — Seat warmer burns

Passengers should use extreme caution when using seat warmers due to the possibility of excess heating or burns. The occupants must be able to feel if the seat is becoming too warm and to turn the seat warmer off. The seat warmer may cause burns even at low temperatures, especially if used for long periods of time.

In particular, the driver must exercise extreme care for the following types of passengers:

1.Infants, children, elderly or disabled persons, or hospital outpatients

2.Persons with sensitive skin or those that burn easily

3.Fatigued individuals

4.Intoxicated individuals

5.Individuals taking medication that can cause drowsiness or sleepiness (sleeping pills, cold tablets, etc.)

OUB031009

Seatback pocket

The seatback pocket is provided on the back of the front passenger’s seatback.

WARNING — Seatback pocket

Do not put heavy or sharp objects in the seatback pocket. An occupant could contact such objects in a crash. Heavy objects in the front passenger seatback could also interfere with the airbag sensing system.

OUB031043N

Rear seat adjustment

Headrest

The rear seat is equipped with headrests in all the seating positions for the occupant’s safety and comfort.

The headrest not only provides comfort for passengers, but also helps protect the head and neck in the event of a collision. For maximum effectiveness in case of an accident, the headrest should be adjusted so the middle of the headrest is at the same height of the center of gravity of an occupant’s head. Generally, the center of gravity of most people’s head is similar with the height as the top of their eyes.

Also adjust the headrest as close to your head as possible. For this reason, the use of a cushion that holds the body away from the seatback is not recommended.

WARNING — Headrest removal

Do not operate the vehicle with the headrests removed. Headrests can provide critical neck and head support in a crash.

OUB031016N

Adjusting the height up and down (if equipped)

To raise the headrest, pull it up to the desired position (1). To lower the headrest, push and hold the release button (2) on the headrest support and lower the headrest to the desired position (3).

OUB031017N

Removal and installation

To remove the headrest, raise it as far as it can go then press the release button

(1) while pulling the headrest upward (2). To reinstall the headrest, put the headrest poles (3) into the holes while pressing the release button (1). Then adjust it to the appropriate height and ensure that it locks in position.

Make sure the headrest locks in position after adjusting.

Folding the rear seat

The rear seatbacks may be folded to facilitate carrying long items or to increase the luggage capacity of the vehicle.

WARNING

Never allow passengers sit on top of the folded down seatback while the vehicle is moving. This is not a proper seating position and no seat belts are available for use. This could result in serious injury or death in case of an accident or sudden stop.

WARNING — Objects

Objects carried on the folded down seatback should not extend higher than the top of the front seatbacks. This could allow cargo to slide forward and cause injury or damage during sudden stops.

OUB031049K

To fold down the rear seatback:

• 4 door

1.Make sure the rear seat belt webbing is in the guide to prevent the seat belt from being damaged.

2.Set the front seatback to the upright position and if necessary, slide the front seat forward.

3.Lower the rear headrests to the lowest position.

OUB031051K

4.Pull the lock release lever (1) and fold the rear seatback forward and down firmly.

If the seat belt remains extended after returning the seatback to it’s upright position, pull the seatbelt outward and release to retract the seatbelt.

OUB032049

• 5 door

1.Make sure the rear seat belt webbing is in the guide to prevent the seat belt from being damaged.

2.Set the front seatback to the upright position and if necessary, slide the front seat forward.

3.Lower the rear headrests to lowest position.

OUB032018N

4.Pull the lock release lever (1) and fold the rear seatback forward and down firmly.

If the seat belt locks after unfolding the rear seatback, pull out the locked seat belt, release it then pull it out again.

To unfold the rear seat

1.To use the rear seat, lift and pull the seatback backward. Pull the seatback firmly until it clicks into place. Make sure the seatback is locked in place. When you return the seatback to its upright position, always be sure it has locked into position by pushing on the top of the seatback.

If you can not see the red line at the bottom of folding lever, it means the seatback is locked completely.

2.Return the rear seat belt to the proper position.

3.When the seatback is completely installed, check the seatback folding lever again.

When returning the rear seatbacks to the upright position, remember to return the rear shoulder belts to their proper position.

Safety features of your vehicle

WARNING — Rear seatback

When returning the rear seatback from a folded to an upright position, hold the seatback and return it slowly. Ensure that the seatback is completely locked into its upright position by pushing on the top of the seatback. In an accident or sudden stop, the unlocked seatback could allow cargo to move forward with great force and enter the passenger compartment.

WARNING — Cargo

Do not place heavy objects in the rear seats, since they cannot be properly secured and may hit vehicle occupants in a frontal collision.

SEAT BELTS

Seat belt restraint system

Seat belts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided.

Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed.

A slack belt will greatly reduce the protection afforded to the wearer.

Care should be taken to avoid contamination of the webbing with polishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged.

•For maximum restraint system protection, the seat belts must always be used whenever the vehicle is moving. A properly positioned shoulder belt should be positioned midway over your shoulder across your collarbone.

•Never allow children to ride in the front passenger seat. See child restraint system section for further discussion.

WARNING — Shoulder belt

Never wear the shoulder belt under your arm or behind your back. An improperly positioned shoulder belt cannot protect the occupant in a crash.

WARNING — Damaged seat belt

Replace the entire seat belt assembly if any part of the webbing or hardware is damage as you can no longer be sure that a damage seat belt will provide protection in a crash.

WARNING — Twisted seat belt

Make sure your seat belt is not twisted when worn. A twisted seat belt may not properly protect you in an accident and could even cut into your body.

WARNING — Seat belt buckle

Do not allow foreign material (gum, crumbs, coins, etc.) to obstruct the seat belt buckle. This may prevent the seat belt from fastening securely.

Safety features of your vehicle

Safety features of your vehicle

WARNING

Riding in an improper position adversely affects the front passenger’s seat belt warning system. It is important for the driver to instruct the passenger as to the proper seating instructions as contained in this manual.

B180A01NF-1

Seat belt — Driver’s 3-point system with emergency locking retractor

To fasten your seat belt:

To fasten your seat belt, pull it out of the retractor and insert the metal tab (1) into the buckle (2). There will be an audible «click» when the tab locks into the buckle. The seat belt automatically adjusts to the proper length only after the lap belt portion is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It will also lock if you try to lean forward too quickly.

Safety features of your vehicle

Front seat

OTA030017

Height adjustment

You can adjust the height of the shoulder belt anchor to one of the 4 positions for maximum comfort and safety.

The height of the adjusting seat belt should not be too close to your neck. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder near the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appropriate position.

To raise the height adjuster, pull it up (1). To lower it, push it down (3) while pressing the height adjuster button (2).

Release the button to lock the anchor into position. Try sliding the height adjuster to make sure that it has locked into position.

WARNING — Shoulder belt position

Never position the shoulder belt across your neck or face.

WARNING — Seat belt replacement

Replace your seat belts after being in an accident. Failure to replace seat belts after an accident could leave you with damaged seat belts that will not provide protection in the event of another collision.

B200A01NF

You should place the lap belt portion as low as possible and snugly across your hips. If the lap belt is located too high on your waist, it may increase the chance of injury in the event of a collision.

The arm closest to the seat belt buckle should be over the belt while the other arm should be under the belt as shown in the illustration.

Seat belts — Front passenger and rear seat 3-point system with combination locking retractor

To fasten your seat belt:

Combination retractor type seat belts are installed in the rear seat positions to help accommodate the installation of child restraint systems. Although a combination retractor is also installed in the front passenger seat position, it is strongly recommended that children always be seated in the rear seat. NEVER place any infant restraint system in the front seat of the vehicle.

This type of seat belt combines the features of both an emergency locking retractor seat belt and an automatic locking retractor seat belt. To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible «click» when the tab locks into the buckle. When not securing a child restraint, the seat belt operates in the same way as the driver’s seat belt (Emergency Locking Retractor Type). It automatically adjusts to the proper length only after the lap belt portion of the seat belt is adjusted manually so that it fits snugly around your hips.

OUB031020N

When using the rear center seat belt, the buckle with the “CENTER” mark must be used.

B210A01NF-1

To release the seat belt:

The seat belt is released by pressing the release button (1) of the locking buckle. When it is released, the belt should automatically draw back into the retractor.

If this does not happen, check the belt to be sure it is not twisted, then try again.

OMG035300

Pre-tensioner seat belt

Your vehicle is equipped with driver’s and front passenger’s pre-tensioner seat belts. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against the occupant’s body in certain frontal collisions (or side collisions). The pre-tensioner seat belts may be activated in crashes, where the frontal collision is severe enough.

When the vehicle stops suddenly, or if the occupant tries to lean forward too quickly, the seat belt retractor will lock into position. In certain frontal collisions, the pre-tensioner will activate and pull the seat belt into tighter contact against the occupant’s body.

If the system senses excessive seat belt tension on the driver or passenger’s seat belt when the pre-tensioner activates, the load limiter inside the pre-tensioner will release some of the pressure on the affected seat belt.

1KMB3311A

The seat belt pre-tensioner system consists mainly of the following components. Their locations are shown in the illustration:

1.SRS air bag warning light

2.Retractor pre-tensioner assembly

3.SRS control module

4.Anchor pre-tensioner assembly

Both the driver’s and front passenger’s pre-tensioner seat belts may be activated in certain frontal collisions.

The pre-tensioners will not be activated if the seat belts are not being worn at the time of the collision.

NOTICE

When the pre-tensioner seat belts are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger compartment. These are normal operating conditions and are not hazardous.

WARNING — Skin irritation

Wash all exposed skin areas thoroughly after an accident in which the pre-tensioner seat belts were activated. The fine dust from the pre-tensioner activation may cause skin irritation and should not be breathed for prolonged periods.

Because the sensor that activates the SRS air bag is connected with the pretensioner seat belt, the SRS air bag warning light ( ) on the instrument panel will illuminate for approximately 6 seconds after the ignition switch has been turned to the ON position, and then it should turn off.

If the pre-tensioner seat belt does not work properly, this warning light will illuminate even if the SRS air bag has not malfunctioned. If the SRS air bag warning light does not illuminate when the ignition switch is turned ON, or if it remains illuminated after illuminating for approximately 6 seconds, or if it illuminates while the vehicle is being driven, please have an authorized Kia dealer inspect the pre-tensioner seat belt or SRS air bag system as soon as possible.

NOTICE

Do not attempt to service or repair the pre-tensioner seat belt system in any manner. Do not attempt to inspect or replace the pre-tensioner seat belts yourself. This must be done by an authorized Kia dealer.

WARNING — Hot pretensioner

Do not touch the pre-tensioner seat belt assemblies for several minutes after they have been activated. When the pre-tensioner seat belt mechanism fires during a collision the pre-tensioner becomes hot and can burn you.

Pre-tensioners are designed to operate only one time. After activation, pre-ten- sioner seat belts must be replaced. If the pre-tensioner must be replaced, contact an authorized Kia dealer.

Seat belt precautions

Infant or small child

You should be aware of the specific requirements in your country. Child and/or infant seats must be properly placed and installed in the rear seat. For more information about the use of these restraints, refer to “Child restraint system” in this section.

Larger children

Children who are too large for child restraint systems should always occupy the rear seat and use the available lap/shoulder belts. The lap portion should be fastened and snugged on the hips and as low as possible. Check if the belt fits periodically. A child’s squirming could put the belt out of position. Children are given the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. If a larger child (over age 12) must be seated in the front seat, the child should be securely restrained by the available lap/shoulder belt and the seat should be placed in the rearmost position. Children age 12 and under should be restrained securely in the rear seat. NEVER place a child age 12 and under in the front seat. NEVER place a rear facing child seat in the front seat of a vehicle.

If the shoulder belt portion slightly touches the child’s neck or face, try placing the child closer to the center of the vehicle. If the shoulder belt still touches their face or neck they need to be returned to a child restraint system.

WARNING — Small children

Do not allow small children to ride in the vehicle without an appropriate child restraint system. If the shoulder belt comes in contact with your child’s neck or face your child is too small to ride in the vehicle. In a crash the seat belt will inflict injury to your child’s neck, throat and face.

Restraint of pregnant women

Pregnant women should wear lap/shoulder belt assemblies whenever possible according to specific recommendations by their doctors. The lap portion of the belt should be worn AS SNUGLY AND LOW AS POSSIBLE.

WARNING — Pregnant women

Pregnant women must never place the lap portion of the seat belt above or on the abdomen where the fetus is located. The force of the seat belt during a collision will crush the fetus.

Injured person

A seat belt should be used when an injured person is being transported. When this is necessary, you should consult a physician for recommendations.

One person per belt

Two people (including children) should never attempt to use a single seat belt. This could increase the severity of injuries in case of an accident.

Do not lie down

To reduce the chance of injuries in the event of an accident and to achieve maximum effectiveness of the restraint system, all passengers should be sitting up and the front seats should be in an upright position when the vehicle is moving. A seat belt cannot provide proper protection if the person is lying down in the rear seat or if the front seat is in a reclined position.

Care of seat belts

Seat belt systems should never be disassembled or modified. In addition, care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or other abuse.

WARNING — Pinched seat belt

Make sure that the webbing and/or buckle does not get caught or pinched in the rear seat when returning the rear seatback to its upright position. A caught or pinched webbing/buckle may become damaged and could fail during a collision or sudden stop.

Periodic inspection

All seat belts should be inspected periodically for wear or damage of any kind. Any damaged parts should be replaced as soon as possible.

Keep belts clean and dry

Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not be used because they may damage and weaken the fabric.

When to replace seat belts

The entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an accident. This should be done even if no damage is visible. Additional questions concerning seat belt operation should be directed to an authorized Kia dealer.

CHILD RESTRAINT SYSTEM

Children riding in the car should sit in the rear seat and must always be properly restrained to minimize the risk of injury in an accident, sudden stop or sudden maneuver. According to accident statistics, children are safer when properly restrained in the rear seats than in the front seat. Larger children not in a child restraint should use one of the seat belts provided.

You should be aware of the specific requirements in your country. Child and/or infant safety seats must be properly placed and installed in the rear seat. You must use a commercially available child restraint system that meets the requirements of the safety standards of your country.

Child restraint systems are designed to be secured in vehicle seats by seat belt, or by a tether anchor and/or LATCH anchors (if equipped).

Children could be injured or killed in a crash if their restraints are not properly secured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits your vehicle seat and seat belts, and fits your child. Follow all the instructions provided by the manufacturer when installing the child restraint system.

WARNING— Restraint location

Never install a child or infant seat on the front passenger’s seat.

A child riding in the front passenger seat can be forcefully struck by an inflating airbag.

WARNING— Hot child restraint

A child restraint system can become very hot if it is left in a closed vehicle on a sunny day. Be sure to check the seat cover, buckles and latches before placing a child in the restraint system.

When the child restraint system is not in use, store it in the luggage area or fasten it with a seat belt so that it will not be thrown forward in case of a sudden stop or an accident.

WARNING — Holding children

Never hold a child in your arms or lap when riding in a vehicle. The violent forces created during a crash will tear the child from your arms and throw the child against the car’s interior.

Always use a child restraint system which is appropriate for your child’s height and weight.

WARNING — Unattended Children

Never leave children unattended in a vehicle. The car can heat up very quickly, resulting in injuries to the child in the vehicle.

WARNING — Seat belt use

Do not use one seat belt for two occupants at the same time. This will eliminate any safety benefit provided by the seat belt to the occupants.

Safety features of your vehicle

Rearward-facing child restraint system

CRS09

Forward-facing child restraint system

OUB031012N

Using a child restraint system

For small children and babies, the use of a child seat or infant seat is required. This child seat or infant seat should be of appropriate size for the child and should be installed in accordance with the manufacturer’s instructions.

For safety reasons, we recommend that the child restraint system be used in the rear seats.

Safety features of your vehicle

Since all passenger seat belts move freely under normal conditions and only lock under extreme or emergency conditions (emergency lock mode), you must manually change these seat belts to the auto lock mode to secure a child restraint.

If the seat belt does not operate as described in this section, have the system checked immediately by your authorized Kia dealer.

WARNING — Child seat installation

•Always follow the instructions provided by the child restraint system manufacturer. Child restraint system manufacturers know their products best.

•Failure to observe this manual’s instructions regarding child restraint system and the instructions provided with the child restraint system could result in the improper installation of the child restraint system which may reduce the protection to your child in a crash or a sudden stop.

E2MS103005

Lacing a passenger seat belt into the auto lock mode

The auto lock mode will help prevent the normal movement of the child in the vehicle from causing the seat belt to loosen and compromise the child restraint system. To secure a child restraint system, use the following procedure.

OEN036101

To install a child restraint system on the outboard or center rear seats, do the following:

1.Place the child restraint system in the seat and route the lap/shoulder belt around or through the restraint, following the restraint manufacturer’s instructions. Be sure the seat belt webbing is not twisted.

2.Fasten the lap/shoulder belt latch into the buckle. Listen for the distinct “click” sound.

Position the release button so that it is easy to access in case of an emergency.

OEN036102

3.Pull the shoulder portion of the seat belt all the way out. When the shoulder portion of the seat belt is fully extended, it will shift the retractor to the “Auto Lock” (child restraint) mode.

OEN036103

4.Slowly allow the shoulder portion of the seat belt to retract and listen for an audible “clicking” or “ratcheting” sound. This indicates that the retractor is in the “Auto Lock” mode. If no distinct sound is heard, repeat steps 3 and 4.

OEN036104

5.Remove as much slack from the belt as possible by pushing down on the child restraint system while feeding the shoulder belt back into the retractor.

6.Push and pull on the child restraint system to confirm that the seat belt is holding it firmly in place. If it is not, release the seat belt and repeat steps 2 through 6.

7.Double check that the retractor is in the “Auto Lock” mode by attempting to pull more of the seat belt out of the retractor. If you cannot, the retractor is in the “Auto Lock” mode.

The lap/shoulder belt automatically returns to the “emergency lock mode” whenever the belt is allowed to retract fully.

Therefore, the preceding seven steps must be followed each time a child restraint is installed.

To remove the child restraint, press the release button on the buckle and then pull the lap/shoulder belt out of the restraint and allow the seat belt to retract fully.

WARNING — Auto lock mode

Set the retractor to Automatic Lock mode when installing any child restraint system.

If the retractor is not in the Automatic Locking mode, the child restraint can move when your vehicle turns or stops suddenly.

■ 4 door

OUB031050K

■ 5 door (Type A)

OUB031010

■ 5 door (Type B)

OUB031011

Securing a child restraint seat with tether anchorage system

Child restraint hook holders are located on the floor behind the rear seats.

OUB031013N

1.Route the child restraint seat tether strap over the seatback.

For vehicles with adjustable headrest, route the tether strap under the headrest and between the headrest posts, otherwise route the tether strap over the top of the seatback.

2.Connect the tether strap hook to the appropriate child restraint hook holder and tighten to secure the child restraint seat.

WARNING — Tether strap

Never mount more than one child restraint to a single tether or to a single lower anchorage point. The increased load caused by multiple seats may cause the tethers or anchorage points to break.

Check that the child restraint system is secure by pushing and pulling it in different directions. Incorrectly fitted child restraints may swing, twist, tip or separate causing death or serious injury.

1SAE3090A

Securing a child restraint seat with child seat lower anchor system

Some child seat manufacturers make child restraint seats that are labeled as LATCH or LATCH-compatible child restraint seats. LATCH stands for «Lower Anchors and Tethers for Children». These seats include two rigid or webbing mounted attachments that connect to two LATCH anchors at specific seating positions in your vehicle. This type of child restraint seat eliminates the need to use seat belts to attach the child seat in the rear seats.

Lower Anchor

Lower Anchor

Position Indicator

OUB031039N

Child restraint symbols are located on the left and right rear seat backs to indicate the position of the lower anchors for child restraints.

WARNING — Unused rear seatbelts

Always fasten the seatbelts behind the child restraint seat when they are not used to secure the child seat. Failure to do so may result in child strangulation.

OUN036140L

LATCH anchors have been provided in your vehicle. The LATCH anchors are located in the left and right outboard rear seating positions. Their locations are shown in the illustration. There is no LATCH anchor provided for the center rear seating position.

The LATCH anchors are located between the seatback and the seat cushion of the rear seat left and right outboard seating positions.

When you install your child’s restraint system using the LATCH anchors buckle the shoulder lap belt, then lock the retractor and pull the belt to remove the slack in the belt so it lies flat against the vehicle seat.

Follow the child seat manufacturer’s instructions to properly install child restraint seats with LATCH or LATCHcompatible attachments.

Once you have installed the LATCH child restraint, assure that the seat is properly attached to the LATCH and tether anchors.

Also, test the child restraint seat before you place the child in it. Tilt the seat from side to side. Also try to tug the seat forward. Check to see if the anchors hold the seat in place.

WARNING — LATCH lower anchors

Never attempt to attach a LATCH equipped seat in the center seating position. LATCH lower anchors are only to be used with the left and right rear outboard seating positions. You may damage the anchors or the anchors may fail and break in a collision.

How does the air bag system operate

•Air bag are activated (able to inflate if necessary) only when the ignition switch is turned to the ON or START the appropriate position.

•Air bags inflate instantly in the event of serious frontal or side collision (if equipped with side impact air bag or curtain air bag) in order to help protect the occupants from serious physical injury.

•There is no single speed at which the air bags will inflate.

Generally, air bags are designed to inflate based upon the severity of a collision and its direction. These two factors determine whether the sensors produce an electronic deployment/ inflation signal.

•Air bag deployment depends on a number of complex factors including vehicle speed, angles of impact and the density and stiffness of the vehicles or objects which your vehicle hits in the collision. Though, factors are not limited to those mentioned above.

•The front air bags will completely inflate and deflate in an instant.

It is virtually impossible for you to see the air bags inflate during an accident. It is much more likely that you will simply see the deflated air bags hanging out of their storage compartments after the collision.

•In order to help provide protection in a severe collision, the air bags must inflate rapidly. The speed of air bag inflation is a consequence of extremely short time in which a collision occurs and the need to get the air bag between the occupant and the vehicle structures before the occupant impacts those structures. This speed of inflation reduces the risk of serious or lifethreatening injuries in a severe collision and is thus a necessary part of air bag design.

However, air bag inflation can also cause injuries which can include facial abrasions, bruises and broken bones because the inflation speed also causes the air bags to expand with a great deal of force.

•There are even circumstances under which contact with the steering wheel air bag can cause fatal injuries, especially if the occupant is positioned excessively close to the steering wheel.

WARNING — Airbag inflation

Sit as far back as possible from the steering wheel while still maintaining comfortable control of your vehicle. A distance of at least 10″ from your chest to the steering wheel is recommended. Failure to do so can result in airbag inflation injuries to the driver.

Safety features of your vehicle

Noise and smoke

When the air bags inflate, they make a loud noise and they leave smoke and powder in the air inside of the vehicle. This is normal and is a result of the ignition of the air bag inflator. After the air bag inflates, you may feel substantial discomfort in breathing due to the contact of your chest to both the seat belt and the air bag, as well as from breathing the smoke and powder. Open your doors and/or windows as soon as possible after the impact in order to reduce discomfort and prevent prolonged exposure to smoke and powder.

Though smoke and powder are nontoxic, it may cause irritation to the skin (eyes, nose and throat etc). If this is the case, wash and rinse with the cold water immediately and consult the doctor if the symptom persists.

WARNING

— Hot components

Do not touch the air bag storage area’s internal components immediately after airbag inflation. The air bag related parts in the steering wheel, instrument panel and the roof rails above the front and rear doors are very hot. Hot components can result in burn injuries.

1JBH3051

Installing a child restraint on a front passenger’s seat is forbidden

Never place a rear-facing child restraint in the front passenger’s seat. If the air bag deploys, it would impact the rear-fac- ing child restraint, causing serious or fatal injury.

In addition, do not place front-facing child restraint in the front passenger’s seat either. If the front passenger air bag inflates, it would cause serious or fatal injuries to the child.

W7-147

Air bag warning light

The purpose of the air bag warning light in your instrument panel is to alert you of a potential problem with your air bag — Supplemental Restraint System (SRS).

When the ignition switch is turned ON, the indicator light should illuminate for approximately 6 seconds, then go off.

Have the system checked by an authorized Kia dealer if:

•The light does not turn on briefly when you turn the ignition ON.

•The light stays on after illuminating for approximately 6 seconds.

•The light comes on while the vehicle is in motion.

OUB031041N

SRS components and functions

The SRS consists of the following components:

1.Driver’s front air bag module

2.Passenger’s front air bag module

3.Side impact air bag modules

4.Curtain air bag modules

5.Retractor pre-tensioner assemblies*

6.Air bag warning light

7.SRS control module (SRSCM)

8.Front impact sensors

9.Side impact sensors

10.PASSENGER AIR BAG “OFF” indicator (Front passenger’s seat only)

11.Occupant detection system (Front passenger’s seat only)

12.Driver’s and front passenger’s seat belt buckle sensors

13.Anchor pre-tensioner assemblies *: if equipped

The SRSCM continually monitors all SRS components while the ignition switch is ON to determine if a crash impact is severe enough to require air bag deployment or pre-tensioner seat belt deployment.

The SRS air bag warning light on the instrument panel will illuminate for about 6 seconds after the ignition switch is turned to the ON position, after which the air bag warning light should go out.

If any of the following conditions occurs, this indicates a malfunction of the SRS. Have an authorized Kia dealer inspect the air bag system as soon as possible.

•The light does not turn on briefly when you turn the ignition ON.

•The light stays on after illuminating for approximately 6 seconds.

•The light comes on while the vehicle is in motion.

Driver’s front air bag (1)

B240B01L

The air bag modules are located both in the center of the steering wheel and in the front passenger’s panel above the glove box. When the SRSCM detects a sufficiently severe impact to the front of the vehicle, it will automatically deploy the front air bags.

Driver’s front air bag (2)

B240B02L

Upon deployment, tear seams molded directly into the pad covers will separate under pressure from the expansion of the air bags. Further opening of the covers then allows full inflation of the air bags.

Driver’s front air bag (3)

B240B03L

A fully inflated air bag, in combination with a properly worn seat belt, slows the driver’s or the passenger’s forward motion, reducing the risk of head and chest injury.

After complete inflation, the air bag immediately starts deflating, enabling the driver to maintain forward visibility and the ability to steer or operate other controls.

Passenger’s front air bag

B240B05L

WARNING — Air bag obstructions

Do not install or place any accessories on the steering wheel, instrument panel, or on the front passenger’s panel above the glove box in a vehicle Such objects may become dangerous projectiles if the air bag deploys.

Safety features of your vehicle

NOTICE

Before you replace a fuse or disconnect a battery terminal, turn the ignition switch to the LOCK position and remove the ignition key. Never remove or replace the air bag related fuse(s) when the ignition switch is in the ON position. Failure to heed this warning will cause the SRS air bag warning light to illuminate.

OUB031037N

Occupant detection system

Your vehicle is equipped with an occupant detection system in the front passenger’s seat.

The occupant detection system is designed to detect the presence of a properly-seated front passenger and determine if the passenger’s front air bag should be enabled (may inflate) or not. The driver’s front air bag is not affected or controlled by the occupant detection system.

Main components of occupant detection system

•A detection device located within the front passenger seat track.

•Electronic system to determine whether passenger air bag systems should be activated or deactivated.

•An indicator light located on the instrument panel which illuminates the words PASSENGER AIR BAG “OFF” indicating the front passenger air bag system is deactivated.

•The instrument panel air bag warning light is interconnected with the occupant detection system.

If the front passenger seat is occupied by a person that the system determines to be of adult size, and he/she sits properly (sitting upright with the seatback in an upright position, centered on the seat cushion with their seat belt on, legs comfortably extended and their feet on the floor), the PASSENGER AIR BAG “OFF” indicator will turn off and the front passenger’s air bag will be able to inflate, if necessary, in frontal crashes.

You will find the PASSENGER AIR BAG “OFF” indicator on the center facia panel. This system detects the conditions 1~4 in the following table and activates or deactivates the front passenger air bag based on these conditions.

Safety features of your vehicle

Condition and operation in the front passenger occupant detection system

*1) The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may recognize him/her as a child depending on his/her physique and posture.

*2) Do not allow children to ride in the front passenger seat. When a smaller child than the same age sits in the front passenger seat, the system may recognize him/her as an infant depending on his/her physique or posture.

*3) Never install a child restraint system on the front passenger seat.

*4) The PASSENGER AIR BAG «OFF» indicator may turn on or off when a child above 12 months to 12 years old (with or without child restraint system) sits in the front passenger seat. This is a normal condition.

WARNING — ODS system

Riding in an improper position adversely affects the occupant detection system (ODS) and may result in the deactivation of front passenger airbag. It is important for the driver to instruct the passenger as to the proper seating instructions as contained in this manual.

(Continued)

РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ KIA RIO.pdf

Adobe Acrobat Document
5.1 MB

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) SHELL HX8 5W40

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W-40 SHELL HELIX HX8 550051529 / 550052837

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

5. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) TOTAL 5W30 NFC

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) TOTAL QUARTZ 9000 FUTURE NFC 5W30 4L 183450 / 10230501 / 10990501 / 213836

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) SHELL 5W40

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO III) 4L 5W40 SHELL HELIX ULTRA

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

Комплект для ТО4-ТО8 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) SHELL 5W40

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W40 SHELL HELIX ULTRA

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

6. Оригинальные свечи зажигания (4шт) Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 1885410080 / 1885510060 / 1885810090

7. Оригинальный топливный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 311121R000 / S311121R000

8. Тормозная жидкость 1L DOT4 TEXTAR / BOSCH / MANNOL Киа Рио 1.4/1.6 2012-2017 (KIA RIO)

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) SHELL 5W30

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W30 SHELL HELIX ULTRA

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

Комплект для ТО4-ТО8 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) SHELL 5W30

1. Моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W30 SHELL HELIX ULTRA

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO III 1.4 / 1.6) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

6. Оригинальные свечи зажигания (4шт) Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 1885410080 / 1885510060 / 1885810090

7. Оригинальный топливный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 311121R000 / S311121R000

8. Тормозная жидкость 1L DOT4 TEXTAR / BOSCH / MANNOL Киа Рио 1.4/1.6 2012-2017 (KIA RIO)

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) HYUNDAI PREMIUM GASOLINE 5W20 ПРЕДОПЛАТА 20%

1. Оригинальное моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W20 HYUNDAI PREMIUM GASOLINE 0510000421

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 20%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк.
Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и обмену.

Комплект для ТО4-ТО8 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) HYUNDAI PREMIUM GASOLINE 5W20 ПРЕДОПЛАТА 10%

1. Оригинальное моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W20 HYUNDAI PREMIUM GASOLINE 0510000421

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

6. Оригинальные свечи зажигания (4шт) Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 1885410080 / 1885510060 / 1885810090

7. Оригинальный топливный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 311121R000 / S311121R000

8. Тормозная жидкость 1L DOT4 BREMBO / TEXTAR / BOSCH / MANNOL Киа Рио 1.4/1.6 2012-2017 (KIA RIO)

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 10%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк.
Предоплата — 10% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и обмену.

Комплект для ТО1-ТО2-ТО3-ТО5-ТО6-ТО7-ТО9-ТО10 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) HYUNDAI SUPER EXTRA GASOLINE 5W30

1. Оригинальное моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W30 HYUNDAI SUPER EXTRA GASOLINE 0510000410

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

Комплект для ТО4-ТО8 Киа Рио 1.4/1.6 2012-2017 (KIA RIO) HYUNDAI SUPER EXTRA GASOLINE 5W30

1. Оригинальное моторное масло Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 4L 5W30 HYUNDAI SUPER EXTRA GASOLINE 0510000410

2. Оригинальный масляный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2630035505 / S2630035505

3. Оригинальная прокладка сливной пробки Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 2151323001

4. Оригинальный фильтр салона Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 971334L000

5. Оригинальный воздушный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 281131R100 / S281131R100

6. Оригинальные свечи зажигания (4шт) Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 1885410080 / 1885510060 / 1885810090

7. Оригинальный топливный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) 311121R000 / S311121R000

8. Тормозная жидкость 1L DOT4 TEXTAR / BOSCH / MANNOL Киа Рио 1.4/1.6 2012-2017 (KIA RIO)

 =
581014LA00

В комментариях к заказу укажите VIN для проверки применимости детали.

В комментариях к заказу укажите VIN для проверки применимости детали.

Цена за два диска.

В комментариях к заказу укажите VIN для проверки применимости детали.

Цена за два диска.

В комментариях к заказу укажите VIN для проверки применимости детали.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

Цена за 2 диска.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

Цена за 2 диска.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

Тормозную жидкость нужно менять каждые 30 000 км

Для полной замены нужно от 1 до 2 л

Тормозную жидкость нужно менять каждые 30 000 км

Для полной замены нужно от 1 до 2 л

Тормозную жидкость менять каждые 30 000 км

Для полной замены нужно от 1 до 2 л

Масло АКПП Киа Рио 1.4/1.6 2012-2015 (KIA RIO) рекомендуется менять каждые 60 000 км.

В комплект входит:

1. Оригинальное масло АКПП Киа Рио 1.4/1.6 2012-2015 (KIA RIO) ATF SP-III
(4л) 0450000400 — 2 шт

2. Оригинальный фильтр АКПП Киа Рио 1.4/1.6 2012-2015 (KIA RIO)
4632123000 / 4632123001

3. ГЕРМЕТИК ДЛЯ АКПП VICTOR REINZ (70мл) Киа Рио 1.4/1.6 2012-2015 (KIA RIO) 703141410

4. Оригинальное уплотнительное кольцо АКПП Киа Рио 1.4/1.6 2012-2015 (KIA
RIO) 1751116000

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
20%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 20% от
стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и обмену.

Для автомобилей с 4-ступенчатой
автоматической коробкой передач 4AT.

Масло АКПП рекомендуется менять каждые 60 000 км.

Для замены нужно от 4 до 8 литров.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
30%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

Для автомобилей с 4-ступенчатой
автоматической коробкой передач 4AT.

В комментариях к заказу
укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА
30%

Товар доступен под заказ.
Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и
обмену.

Для автомобилей с 4-ступенчатой
автоматической коробкой передач 4AT.

Комплект для замены масла АКПП Киа
Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) ПРОВЕРКА ПО VIN SP4

Масло АКПП Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) рекомендуется менять каждые 60 000 км.

В комплект входит:

1. Оригинальное масло АКПП Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) ATF SP-IV (1л) 0450000115 — 8 шт

2. Оригинальный фильтр АКПП Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) 4632126000

3. ГЕРМЕТИК ДЛЯ АКПП VICTOR REINZ (70мл) Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ
6AT) 703141410

4. Уплотнительное кольцо сливной пробки АКПП
Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) 2151311000

Для автомобилей с 6-ступенчатой
автоматической коробкой передач 6AT.

В комментариях к заказу
укажите VIN для проверки применимости детали.

Масло АКПП Киа Рио 1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) рекомендуется менять каждые 60 000 км.

Для частичной замены нужно 4 литра

Для автомобилей с 6-ступенчатой автоматической коробкой передач 6AT.

Фильтр АКПП АКПП Киа Рио
1.4/1.6 2015-2017 (RIO РЕСТАЙЛИНГ 6AT) рекомендуется менять каждые 60 000 км.

Для автомобилей с 6-ступенчатой автоматической коробкой передач 6AT

В комментариях к заказу укажите VIN для проверки применимости детали.

Необходим при замене фильтра АКПП

Вязкость — 5W40

Наименование — TOTAL QUARTZ 9000

Объем — 4 л

Состав — Синтетическое

Спецификации ACEA — B4, A3

Спецификации API — CF, SM/SN

Спецификации OEM — BMW Longlife-01, GM-LL-B-025, MB 229.3, PSA B71 2296, VW 500.00, VW 501.01, VW 502.00, VW 505.00

Вязкость — 5W30

Наименование — QUARTZ ENERGY 9000 HKS G-310

Объем — 5л

Состав — Синтетическое

Спецификации ACEA — A5

Спецификации API — SL / SM

Вязкость — 5W-40

Наименование — HELIX HX8 5W-40

Объем — 4 л

Состав — Синтетическое

Спецификации ACEA — B3, B4, A3

Спецификации API — SN+

Спецификации OEM — MB 229.3, Renault RN0700, RN0710; Fiat 9.55535-N2, 9.55535-M2, VW 502.00, VW 505.00

Вязкость — 5W40

Наименование — 1L 5W40 SHELL HELIX ULTRA TAXI 

Объем — 1л

Состав — Синтетическое

Спецификации API — SN / SN+

Спецификации ACEA — A3/B3, A3/B4

Спецификации OEM — MB approval 229.3; VW Standard 502.00, 505.00; Renault RN 0700, RN 0710; соответствует требованиям Fiat (FCA) 9.55535-M2

Вязкость — 5W20

Наименование — PREMIUM GASOLINE

Объем — 4л

Спецификации API — SL

Спецификации ILSAC — GF-III

В комментариях к заказу укажите VIN для проверки применимости
детали.

ПРЕДОПЛАТА 20%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения
предоплаты на карту Сбербанк. Предоплата — 20% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и обмену.

Вязкость — 5W30

Наименование — SUPER EXTRA GASOLINE

Объем — 4 л

Спецификации API — CF-3, SL

Спецификации ILSAC — GF-3

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 30%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту
Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у поставщика под конкретного клиента и не подлежит возврату и обмену.

Топливный фильтр Киа Рио 1.4/1.6 2012-2017 (KIA RIO) нужно менять 

каждые 60 000 км

Антифриз Киа Рио 1.4/1.6 2012-2017 (KIA RIO) нужно менять каждые 45 000 км. 

Для полной замены охлаждающей жидкости нужно 5,3 литра

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 30%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у
поставщика под конкретного клиента и не подлежит возврату и обмену.

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 30%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у
поставщика под конкретного клиента и не подлежит возврату и обмену.

Масло ГУР Киа Рио 1.4/1.6 2012-2015 (KIA RIO) рекомендуется менять каждые
90 000 км.

Для замены нужен 1 литр.

В комментариях к заказу укажите VIN для проверки применимости детали.

ПРЕДОПЛАТА 30%

Товар доступен под заказ. Срок поставки — 2/3 рабочих дня после внесения предоплаты на карту Сбербанк. Предоплата — 30% от стоимости товара. Товар заказывается у
поставщика под конкретного клиента и не подлежит возврату и обмену.