Хендай гетц инструкция по эксплуатации 2007

Hyundai Genuine Parts are only sold through authorized Hyundai Dealership and Service Center.

A100A03L

A100A04L

1.Headlight Leveling Switch (If installed)

2.Front Fog Light Switch (If installed)

3.Multi-Function Light Switch

4.Instrument Cluster

5.Horn and Driver’s Airbag (If installed)

6.Windshield Wiper/Washer Switch

7.Digital Clock

8.Hazard Warning Light

9.Audio System (If installed)

10.Passenger’s Airbag (If installed)

11.Glove Box

12.Hood Release Lever

13.Fuse Box

14.Audio Remote Control Switch (If installed)

15.Heating/Air Conditioning Control Panel (If installed)

16.Cigarette Lighter

17.Ashtray

18.Front Drink Holder

19.Shift Lever (If installed)

20.Parking Brake Lever

21.Rear Drink Holder

YOUR VEHICLE AT A GLANCE

B255A01TB-GAT

INDICATOR SYMBOLS ON THE INSTRUMENT PANEL

SRS (Airbag) Service Reminder

Indicator

Passenger’s Front Airbag OFF

Indicator Light (If Installed)

ABS Service Reminder Indicator

O/D OFF Indicator (Automatic transaxle only)

Turn Signal Indicator Lights

High Beam Indicator Light

Low Oil Pressure Warning Light

Parking Brake/Brake Fluid Level

Warning Light

Charging System Warning Light

Tail Gate Open Warning Light

Door Ajar Warning Light and Chime

Low Fuel Level Warning Light

Malfunction Indicator Light

Seat Belt Warning Light

Electric Power Steering System (EPS)

Warning Light

Electronic Stability Program Indicator

Lights (If Installed)

Immobilizer Warning Light

Diesel Pre-heat Indicator Light (Diesel only)

Fuel Filter Warning Light (Diesel only)

Engine Coolant Temperature Indicator

1- 2 FEATURES OF YOUR HYUNDAI

B010A03O-GAT

FUEL RECOMMENDATIONS Use Unleaded Gasoline

B010A01TB

For Europe – For the optimal vehicle performance, we recommend you to use unleaded gasoline with an octane rating of RON (Research Octane Number) 95 /AKI (Anti Knock Index) 91 or higher.

You may use unleaded gasoline with an octane rating of RON 91~94/AKI 87~90 but it may result in slight performance reduction of the vehicle.

Except Europe – Unleaded gasoline with a Pump Octane Rating of 87 (Research Octane Number 91) or higher must be used in Hyundai vehicle.

If leaded gasoline is used, it will cause the catalytic converter to become ineffective and the emission control system to malfunction. This can also result in increased maintenance expense.

To avoid accidental use of leaded fuel, the large nozzle used with leaded gasoline at service stations can not be insertedintofueltankopeningofHyundai vehicle.

NOTE:

oFor some countries, Hyundai vehicles are designed to use leaded gasoline. When you are going to use leaded gasoline, ask to Hyundai dealer whether leaded gasoline in your vehicle is available or not.

oOctane Rating of leaded gasoline is same with unleaded one.

Diesel fuel

Diesel engine must be operated only on commercially available diesel fuel that complies with EN 590 or comparable standard. (EN stands for «European Norm»). Do not use marine diesel fuel, heating oils, or non-approved fuel additives, as this will increase wear and cause damage to the engine and fuel system.

The use of non-approved fuels and / or fuel additives will result in a limitation of your warranty rights.

Diesel fuel of 52 to 54 cetane is used in

Hyundai vehicle. If two types of diesel fuel are available, use summer or winter fuel properly according to the following temperature conditions.

oAbove -5°C (23°F) … Summer type diesel fuel.

oBelow -5°C (23°F) … Winter type diesel fuel.

Watch the fuel level in the tank very carefully : If the engine stops through fuel failure, the circuits must be completely purged to permit restarting.

!CAUTION:

oDo not let any gasoline or water enter the tank. This would make it necessary to drain it out and to bleed the lines to avoid jamming the injection pump and damaging the engine.

oIn winter, in order to cut down incidents due to freezing, paraffin oil may be added to the fuel if the temperature drops to below -10°C. Never use more than 20% paraffin oil.

Biodiesel

Commercially supplied biodiesel blends of no more than 5% biodiesel, commonly known as «B5 biodiesel» may be used in your vehicle if it meets EN 14214 or equivalent specifications. (EN stands for «European Norm»). The use of biofuels made from rapeseed methyl ester (RME), fatty acid methyl ester (FAME), vegetable oil methyl ester

(VME) etc. or mixing diesel with biodiesel will cause increased wear or damage to the engine and fuel system. Repair or replacement of worn or damaged components due to the use of non approved fuels will not be covered by the manufactures warranty.

!CAUTION:

oNever use any fuel, whether diesel or B5 biodiesel that fails to meet thelatestpetroleumindustryspecification.

oNever use any fuel additives or treatments that are not recommended or approved by the vehicle manufacturer.

B010B01A-AAT

What About Gasohol?

Gasohol (a mixture of 90% unleaded gasoline and 10% ethanol or grain alcohol) may be used in your Hyundai. However, if your engine develops driveability problems, the use of 100% unleaded gasoline is recommended.

Fuels with unspecified quantities of alcohol, or alcohols other than ethanol, should not be used.

B010D01S-AAT

Do not Use Methanol

Fuels containing methanol (wood alcohol) should not be used in your Hyundai. This type of fuel can reduce vehicle performance and damage components of the fuel system.

!CAUTION:

Your Hyundai’s New Vehicle Limited Warranty may not cover damage to the fuel system and performance problems that are caused by the use of methanol or fuels containing methanol.

FEATURES OF YOUR HYUNDAI 1- 3

B010E01A-AAT

Gasolines for Cleaner Air

To help contribute to cleaner air,

Hyundai recommends that you use gasolines treated with detergent additives, which help prevent deposit formation in the engine. These gasolines will help the engine run cleaner and the

Emission Control System performance.

B010F01A-AAT

Operation in Foreign Countries

If you are going to drive your Hyundai in another country, be sure to:

o Observe all regulations regarding registration and insurance.

o Determine that acceptable fuel is available.

1- 4 FEATURES OF YOUR HYUNDAI

B020A01S-GAT

BREAKING IN YOUR NEW HYUNDAI

During the First 2,000 Km (1,200 Miles) (Gasoline Engine)

No formal «break-in» procedure is required with your new Hyundai. However, you can contribute to the economical operation and durability of your Hyundai by observing the following recommendations during the first 2,000 km (1,200 miles).

oDon’t drive faster than 88 km/h (55 mph).

oWhile driving, keep your engine speed (rpm, or revolutions per minute) between 2,000 rpm and 4,000 rpm.

oUse moderate acceleration. Don’t start, depress the accelerator pedal fully.

oFor the first 300 km (200 miles), try to avoid hard stops.

oDon’t lug the engine (in other words, don’t drive so slowly in toohigh a gear that the engine «bucks»: shift to a lower gear).

oWhether going fast or slow, vary your speed from time to time.

oDon’t let the engine idle longer than 3 minutes at one time.

oDon’t tow a trailer during the first 2,000 km (1,200 miles) of operation.

B020B01FC-GAT

BREAKING IN YOUR NEW HYUNDAI

During the First 1,000 Km (600 Miles) (Diesel Engine)

No formal «break-in» procedure is required with your new Hyundai. However, you can contribute to the economical operation and durability of your

Hyundai by observing the following recommendations during the first 1,000 km (600 miles).

o While driving, keep your engine speed (rpm, or revolutions per minute) within 3,000 rpm.

oWhile driving, keep under three quarters of maximum speed.

oUse moderate acceleration. Don’t start, depress the accelerator pedal fully.

oFor the first 300 km (200 miles), try to avoid hard stops.

oDon’t lug the engine (in other words, don’t drive so slowly in too-high a gear that the engine «bucks»: shift to a lower gear).

oWhether going fast or slow, vary your speed from time to time.

oDon’t let the engine idle longer than

3 minutes at one time.

oDon’t tow a trailer during the first

1,000 km (600 miles) of operation.

B030A01A-AAT

KEYS

B030A01E

For greater convenience, the same key operates all the locks in your Hyundai. However, because the doors can be locked without a key, carrying a spare key is recommended in case you accidentally lock one key inside the car.

B030B01A-AAT

Record Your Key Number

B030B01E

A code number is stamped on the number plate that came with the keys to your Hyundai. This key number plate should not be left with the keys but kept in a safe place, not in the vehicle. The key number should also be recorded in a place where it can be found in an emergency.

If you need additional keys, or if you should lose your keys, your authorized Hyundai dealer can make new keys if you can supply the key number.

B880A01A-GAT

IMMOBILIZER SYSTEM (If Installed)

The immobilizer system is an anti-theft device,designedtodeterautomobiletheft.

B880B06A-AAT

Keys

OTB028002

All of the locks fitted to the vehicle are operated by the same key. However, since it is possible to lock the doors without the use of the key, care should be exercised to ensure that the key does not become locked inside the vehicle by mistake.

NOTE:

If you make your own duplicate key, you will not be able to cancel the system or start the engine.

FEATURES OF YOUR HYUNDAI 1- 5

!WARNING:

In order to prevent theft of your vehicle, do not leave spare keys anywhere in your vehicle. Your immobilizer password is a customer unique password and should be kept confidential. Do not leave this number anywhere in your vehicle.

!CAUTION:

oWhen starting the engine, do not use the key with other immobilizer keys in close proximity. Otherwise, the engine may not start or may stop soon after it starts.

Keep each keys separately not to have any malfunction after you receive your new vehicle.

oDo not put metal accessories near the key or ignition switch.

The engine may not start for the metal accessories may interrupt the transponder signal from normally transmitting.

1- 6 FEATURES OF YOUR HYUNDAI

B880C02A-GAT

Key Numbers

OTB028003

The vehicle key number is recorded upon a metal tag attached to the keys when the vehicle is first delivered to you.

The key number should be recorded and kept in a safe place in case the need to order further keys arises. New keys are available from any Hyundai dealer by quoting the relevant key number.

In the interest of security, the metal tag attached to the keys which bears the key number should be removed from the key ring after you receive your new vehicle. In addition, key numbers cannot be provided by Hyundai for security reasons.

If you need additional keys or if you should lose your keys, your authorized Hyundai dealer can make new keys.

B880D02A-GAT

Limp home procedures

HNF2011

In case the immobilizer warning indicator blinks for five seconds when the ignition key is turned to «ON» position, this indicates that the immobilizer system is out of order. And you cannot start the engine without the limp home procedures with ignition key.

The following procedure is how to start the engine with the function of the limp home. (0, 1, 2, 3 as a sample password).

NOTE:

You can get the limp home password when the vehicle is first delivered to you. If you do not have the password, consult your authorized Hyundai dealer.

1.To set the password you may turn the ignition key «ON» and then turn it «OFF» according to the digit numbers, then the immobilizer indicator will blink along with the operation of the ignition key. For example, turn the ignition key once for digit number «1», and twice for «2», and so on.

However, for the digit number «0», you must turn the ignition key for 10 times.

2.Wait for 3~10 seconds.

3.You may set the remaining number of digits by following the same procedures 1 and 2.

4.If all of four digits have been tried successfully, turn the ignition key

«ON» and check that the immobilizer indicator illuminates. From this time, you have to start your engine within 30 seconds. If you start your engine after 30 seconds, your engine will not start.

NOTE:

If the engine dies while driving after limp home procedure, you can start your engine within 8 seconds without limp home procedure again.

5.If the immobilizer indicator blinks for five seconds, you have to try the limp home procedure again from the beginning.

After doing the limp home procedure, you have to consult with your authorized Hyundai dealer as soon as possible.

!CAUTION:

o If you fail to try the limp home procedure with the sequence of three times, you have to wait for about one hour to do the limp home procedure again.

oIf you cannot start your engine in spite of limp home procedure, have your vehicle towed by an authorized Hyundai dealer.

B040A02Y-AAT

DOOR LOCKS

!WARNING:

oUnlocked doors can be dangerous. Before you drive away (especially if there are children in the car), be sure that all the doors are securely closed and locked so that the doors cannot be inadvertently opened from the inside. This helps ensure that doors will not be opened accidentally. Also, when combined with the proper use of seat belts, locking the doors helps keep occupants from being ejected from the car in case of an accident.

oBefore opening the door, always look for and avoid oncoming traffic.

oIn case of accident, the door is unlocked automatically (If Installed).

FEATURES OF YOUR HYUNDAI 1- 7

B040B01A-AAT

Locking and Unlocking Front

Doors With a Key

UNLOCK

LOCK

HTB056

oThe door can be locked or unlocked with a key.

oLock the door by turning the key toward the front of the vehicle and unlock it by turning the key toward the rear.

1- 8 FEATURES OF YOUR HYUNDAI

B040C01FC-GAT

Locking From the Outside

HTB062

The doors can be locked without a key.

To lock the doors from the outside, first push the inside lock switch to the

«LOCK» position, so that the red mark on the switch is not visible, then close the door.

The door will not lock if the key is left in the ignition switch when the front doors close. This is normal operation. (If installed)

NOTE:

oWhen locking the door this way, be careful not to lock the door with the ignition key left in the vehicle.

oTo protect against theft, always remove the ignition key, close all windows, and lock all doors and tail gate when leaving your vehicle unattended.

B040D01FC-GAT

Locking From the Inside

LOCK

UNLOCK

HTB057

To lock the doors from the inside, simply close the door and push the lock switch to the «LOCK» position. When this is done, neither the outside nor the inside door handle can be used.

NOTE:

When the door is locked, the red mark on the switch is not visible and the character «LOCK» on the switch is visible.

B040E04A-AAT

CHILD-PROTECTOR

REAR DOOR LOCK (5door only)

HTB058

Your Hyundai is equipped with a «childprotector» rear door lock assembly. When the lock mechanism is engaged, the rear door cannot be opened from the inside. It’s use is recommended whenever there are small children in the rear seat.

To engage the child-protector feature so that the door cannot be opened from the inside, move the child-protector lever to the «» position and close the door. Move the lever to the «» position when normal door operation is desired.

If you wish to be able to open the door from the outside, the outside door handle will function normally.

B040G02FC-GAT

Central Door Lock (If Installed)

HTB212

The central door locking is operated by pushing the driver’s door lock switch toward the front or rear of the vehicle. If the passenger and rear doors are open when the switch is pushed, the door will remain locked when closed.

NOTE:

oWhen pushing the switch toward the rear, all doors and tail gate will unlock.

When pushing the switch toward the front, all doors and tail gate will lock.

oWhen the door is unlocked, the red mark on the switch is visible and the character «LOCK» on the switch is visible.

oThe central door locking is operated by turning the key (with theftalarm system: driver’s door and passenger’s door, without theftalarm system: driver’s door only) toward the front or rear of the vehicle.

oIf the door is locked/unlocked multiple times in rapid succession with either the vehicle key or door lock switch, the system may stop operating temporarily in order to protect the circuit and prevent damage to system components.

FEATURES OF YOUR HYUNDAI 1- 9

B070A01A-AAT

THEFT-ALARM SYSTEM (If Installed)

This system is designed to provide protection from unauthorized entry into the car. This system is operated in three stages: the first is the «Armed» stage, the second is the «Alarm» stage, and the third is the «Disarmed» stage. If triggered, the system provides an audible alarm with blinking of the turn signal lights.

B070B01O-GAT

Armed Stage

B070B01TB

1- 10 FEATURES OF YOUR HYUNDAI

Park the car and stop the engine. Arm the system as described below.

1)Remove the ignition key from the ignition switch.

2)Make sure that the engine hood and tail gate are locked.

3)Lock the doors using the transmitter of the keyless entry system.

After completion of the steps above, the turn signal lights will blink once to indicate that the system is armed.

NOTE:

1)If any door, tail gate or engine hood remains open, the system will not be armed.

2)If this happens, rearm the system as described above.

!CAUTION:

Do not arm the system until all passengers have left the car. If the system is armed while a passenger(s) remains in the car, the alarm may be activated when the remaining passenger(s) leaves the car.

B070C01FC-GAT

Alarm Stage

The alarm will be activated if any of the following occurs while the car is parked and the system is armed.

1)A front or rear door is opened without using the transmitter.

2)The tail gate is opened without using the transmitter.

3)The engine hood is opened.

The alarming horn will sound and the turn signal light will blink continuously for 27 seconds (E.C only/ Except E.C 3 times). To turn off the system, unlock the door or tail gate with the transmitter.

B070D01TB-AAT

Disarmed Stage

HTB202

The system will be disarmed when the driver’s or passenger’s door is unlocked by depressing the button on the transmitter.

After completion of the step above, the turn signal lights will blink twice to indicate that the system is disarmed.

NOTE:

Once the system has been disarmed, it can not be rearmed except by repeating the arming procedures.

!CAUTION:

Only the transmitter can disarm the armed stage. If the transmitter does not disarm the system, it is necessary to take the following steps;

1.Unlock the door with the key, which will cause, the alarm to be activated.

2.Insert the key in the ignition key cylinder and turn the ignition key to «ON» position.

3.Wait for 30 seconds.

After completing the steps above, the system will be disarmed.

B070F02TB-GAT

Keyless Entry System (If Installed)

Locking doors

1.Close all doors.

2.Push the button on the transmitter.

3.At the same time all doors lock, the turn signal lights will blink once to indicate that the system is armed.

Unlocking doors

1.Push the button on the transmitter.

2.At the same time all doors unlock, the turn signal light will blink twice to indicate that the system is disarmed.

NOTE:

The transmitter will not work if any of following occur:

—The ignition key is in ignition switch.

—You exceed the operating distance limit (10 m).

—The battery in the transmitter is weak.

—Other vehicles or objects may be blocking the signal.

—The weather is extremely cold.

FEATURES OF YOUR HYUNDAI 1- 11

—The transmitter is close to a radio transmitter such as a radio station or an airport which can interfere with normal operation of the transmitter.

When the transmitter does not work correctly, open and close the door with the ignition key. If you have a problem with the transmitter, contact an authorized Hyundai Dealer.

NOTE:

Keep the transmitter away from water or any liquid. If the keyless entry system is inoperative due to exposure to water or liquids, it will not be covered by your manufacturer vehicle warranty.

1- 12 FEATURES OF YOUR HYUNDAI

B070E01TB-GAT

Replacing the battery

When the transmitter’s battery begins to get weak, it may take several pushes on the button to lock or unlock the doors, and the LED will not light. Replace the battery as soon as possible.

Battery type : CR1220

Replacement instructions:

HTB053

1.Remove the screw with a phillips screwdriver.

2.Carefully separate the case with a flat-head screwdriver as shown in the illustration.

HTB054

3.Remove four screws back side of the built-in circuit.

Battery

HTB055

4.Remove the old battery from the case and note the polarity. Make sure the polarity of the new battery is the same (+side facing up), then insert it in the transmitter.

B050A01A-AAT

WINDOW GLASS

HTB257

To raise or lower the window, turn the window regulator handle clockwise or counterclockwise.

!WARNING:

When opening or closing the windows, make sure your passenger’s arms, hands and body are safely out of the way.

B060A01E-AAT

POWER WINDOWS (If Installed)

(1)

HTB064

The power windows operate when the ignition key is in the «ON» position. The main switches are located on the driver’s armrest and control the front and rear windows on both sides of the vehicle. The windows may be opened by depressing the appropriate window switch and closed by pulling up the switch. To open the window on the driver’s side, press the switch(1) down.

The window moves as long as the switch is operated.

HTB066

In order to prevent operation of the passenger front and rear windows, a window lock switch is provided on the armrest of the driver’s door. To disable the power windows, press the window lock switch.

To revert to normal operation, press the window lock switch a second time.

Auto-Down Window

(Driver’s Side)

The Auto-Down window is moved to its fully open position by pushing the switch. To stop at the desired position push the switch again.

FEATURES OF YOUR HYUNDAI 1- 13

!WARNING:

1)Be careful that someone’s head, hands and body are not trapped by a closing window.

2)Never try to operate the main switch on the driver’s door and the individual door window switch in opposing directions at the same time. If this is done, the window will stop and cannot be opened or closed.

3)Do not leave children alone in the car. Always remove the ignition key for their safety.

B080A01A-GAT

ADJUSTABLE FRONT SEATS

!WARNING:

Never attempt to adjust the seat while the vehicle is moving. This could result in loss of control, or an accident which may cause death, serious injury, or property damage.

1- 14 FEATURES OF YOUR HYUNDAI

B080B02A-GAT

FRONT SEATS

Adjusting Seat Forward and

Rearward

HTB024

To move the seat toward the front or rear, pull the lock release lever upward. This will release the seat on its track so you can move it forward or rearward to the desired position. When you find the position you want, release the lever and slide the seat forward or rearward on its track until it locks into the desired position and cannot be moved further.

!WARNING:

To ensure the seat is locked securely, attempt to move the seat forward or rearward without using the lock release lever.

B080C01A-AAT

Adjusting Seatback Angle

HTB026

To recline the seatback, lean forward to take your weight off it, then pull up on the recliner control lever at the outside edge of the seat. Now lean back until the desired seatback angle is achieved. To lock the seatback into position, release the recliner control lever.

!WARNING:

To minimize risk of severe injury in the event of a collision or a sudden stop, both the driver and passenger seatbacks should always be in an upright position while the vehicle is in motion. The protection provided by the seat belts and airbags may be reduced significantly when the seatbacks are reclined. There is greater risk that the driver and passenger will slide under the seat belt which may result in serious injury if a crash occurs when the seatbacks are reclined. The seat belt cannot provide full protection to an occupant if the seat back is reclined.

B080D02JM-AAT

Adjustable Headrests

Lock knob

HFC2028

Headrests are designed to help reduce the risk of neck injuries.

To raise the headrest, pull it up. To lower the headrest, push it down while pressing the lock knob. To remove the headrest, raise it as far as it can go then press the lock knob while pulling upward. This should only be done when the seat is not occupied.

!

WARNING:

B080D01JM

oFormaximumeffectivenessincase of an accident, the headrest should be adjusted so the middle of the headrest is at the same height as the top of the occupant’s eyes. For this reason, the use of a cushion that holds the body away from the seatback is not recommended.

FEATURES OF YOUR HYUNDAI 1- 15

oDo not operate the vehicle with the headrests removed as severe injury to an occupant may occur in the event of an accident. Headrests may provide protection against severe neck injuries when properly adjusted.

oDo not adjust the headrest hejght while the vehicle is in motion.

B083D01NF-AAT

Active Headrests (If Installed)

HNF2041-1

The active headrest is designed to move forward and upward during a rear impact. This helps to prevent the driver’s and front passenger’s head from moving backward and thus helps prevent neck injuries.

1- 16 FEATURES OF YOUR HYUNDAI

B080E01O-AAT

Lumbar Support Control

(Driver’s Seat Only) (If Installed)

HTB027

To adjust the lumbar support, turn the handle on the outboard or left side of the seat. To increase the amount of lumbar support, pull the lever forward. To decrease it, push the lever toward the rear.

B080F01S-AAT

Seat Cushion Height Adjustment

(Driver’s Seat Only) (If Installed)

HTB025

To raise or lower the front part of the seat cushion, turn the front knob forward or rearward. To raise or lower the rear part of the seat cushion, turn the rear knob forward or rearward.

B080G01A-GAT

Adjusting Armrest Angle (Driver’s side only) (If installed)

HTB2049

The armrest will be raised or lowered manually.

To raise the armrest, pull it up.

To lower it, press the armrest down.

B130A01A-AAT

REAR SEAT ENTRY (For 3-door model)

(1)

(2)

HTB258

The front passenger seatback should be tilted to enter the rear seat.

By pulling up on the recliner control lever (1) at the outside of the front passenger seat, the seatback will tilt forward and the seat will automatically slide forward.

Rear seat occupants can tilt the front passenger seatback by depressing the foot lever (2) as shown in the illustration.

!WARNING:

Passengers sitting in the rear seat should be careful not to accidentally press the foot lever (2) while the vehicle is moving, as this may cause the seatback to move forward and injure a front seat occupant.

FEATURES OF YOUR HYUNDAI 1- 17

B080I01FC-GAT

REAR SEAT

Adjusting Seatback Angle

Seatback folding lever

B080I01TB

To recline the seatback, push the seatback folding lever toward the headrest, and release it after the desired seatback angle is achieved.

When you recline the seatback to desired position, always be sure it has locked into position.

!CAUTION:

When reclining the seatback you should adjust the seatback folding lever while standing.

1- 18 FEATURES OF YOUR HYUNDAI

B099A02F-AAT

BEFORE FOLDING THE REAR SEATS

Outboard Rear Seat Belt

In order to prevent the shoulder belt from being damaged while folding the rear seat, the shoulder belt must be passed through the hanger to keep it out of the way.

!CAUTION:

Seat belts must be removed from the hanger when in use.

B090B01TB-GAT

Folding Rear Seatback and Seat

Cushion

For greater convenience, the entire seatback and seat cushion may be folded down and up.

HTB294

Rear Seat Center’s 3 Point Type Seat Belt (If installed)

OTB038146

Seatback folding lever

HTB2006

1.Push the headrest down to the lowest position.

2.To fold down the seatback , push and hold the seatback folding lever toward the headrest, then push down the seatback.

A Type Securing Strap

Seat cushion release handle

HTB030

B Type Securing Strap

Seat cushion release handle

HTB030A

3.A Type: Pull the seat cushion release handle rearward, then lift up the entire seat cushion.

B Type: Pull the seat cushion release handle rearward, then lift up a desired seat cushion.

4.To secure the seat, hook the securing strap under the seat back to the headrest stay of front driver and passenger seat.

5.To return the seatback and seat cushion to its normal position, reverse the above procedure.

oWhen you return the seatback to its upright position, always be sure it is locked into position by pulling and pushing on the top of seatback.

FEATURES OF YOUR HYUNDAI 1- 19

!WARNING:

oWhen you return the folded down seatback to its upright position, make sure the seat belts are in position to be accessible and to function properly.

oWhen you return the folded down seatback to its upright position, be careful not to get your fingers or legs in.

oThe purpose of the fold down rear seatback and the fold forward rear seat cushion is to increase cargo space. Do not allow passengers to sit in the cargo area while the car is moving. This is not a proper seating position and no seat belts are available for use when the seatback is folded down. Passengers who are not properly seated and wearing seat belts could sustain serious injuries or death in case of an accident or a sudden stop.

1- 20 FEATURES OF YOUR HYUNDAI

oObjects should not extend higher than the top of the front seatbacks. This could allow cargo to slide forward and cause injury or damage during sudden stops.

oWhen you return the folded down seatback to its upright position, always be sure to install the headrests in their proper positions. Headrests are important to the safety of occupants in a rear collision. If the headrests are not installed in their proper position, serious injury or death could result if a rear end collision occurs.

B100A01TB-GAT

SEAT WARMER (If installed)

HTB194

The seat warmer is provided to warm the front seats during cold weather. With the ignition key in the «ON» position, push either of the switches to warmthedriver’sseatorthepassenger’s seat.

During mild weather or under conditions where the operation of the seat warmer is not needed, keep the switches in the

«OFF» position.

NOTE:

oThe seat warmer will not operate if the ambient temperature is higher than 37°C (98.6°F).

oIf the seat warmer doesn’t work when ambient temperature is lower than 28°C (82.4°F), it should becheckedatanauthorizeddealer.

!WARNING:

It is recommended that the seat heater not be used when elderly people or people who are ill occupy the seat. Also, do not use the seat warmer if the occupant is sleeping.

B140A01B-GAT

REAR SEAT WARNING

B140A01TB

For the safety of all passengers, luggage or other cargo should not be piled higher than the top of the seatback.

B150A02A-GAT

SEAT BELT PRECAUTIONS

All occupants of the vehicle should wear their seat belts at all times. Indeed, your province’s laws may require that some or all occupants of the vehicle use seat belts.

The possibility of injury or the severity of injury in an accident will be decreased if this elementary safety precaution is observed. In addition, the following recommendations are made:

B150B01Y-GAT

Infant or Small Child

Some countries require the use of child restraint systems for infants and small children. Whether this is required by law or not, it is strongly recommended that a child restraint seat or infant restraint system be used for infants or small children weighing less than 18 kilograms (40 pounds).

NOTE:

Small children are best protected in an accident when properly restrained by a child restraint system.

FEATURES OF YOUR HYUNDAI 1- 21

B150C02A-AAT

Larger Children

Children who are too large for child restraint systems should occupy the rear seat and use the available lap/ shoulder belts. The lap portion should be fastened snug on the hips and as low as possible. Check belt fit periodically. A child’s squirming could put the belt out of position. Children are afforded the most safety in the event of an accident when they are restrained by a proper restraint system in the rear seat. If a larger child (over age 13) must be seated in the front seat, the child should be securely restrained by the available lap/shoulder belt and the seat should be placed in the rearmost position. Children under the age of 13 should be restrained securely in the rear seat. NEVER place a rear facing child seat in the front seat of a vehicle.

1- 22 FEATURES OF YOUR HYUNDAI

B150D01S-AAT

Pregnant Women

The use of a seat belt is recommended for pregnant women to lessen the chance of injury in an accident. When a seat belt is used, it should be placed as low and snugly as possible on the hips, not across the abdomen. For specific recommendations, consult a physician.

B150E01A-AAT

Injured Person

A seat belt should be used when an injured person is being transported.

When this is necessary, you should consult a physician for recommendations.

B150F01A-AAT

One Person Per Belt

Two people (including children) should never attempt to use a single seat belt. This could increase the severity of injuries in case of an accident.

B150G01A-AAT

Do Not Lie Down

To reduce the chance of injuries in the event of an accident, and to achieve maximum effectiveness of the restraint system, all passengers should be sitting up and the front seats should be in an upright position when the car is moving. A seat belt cannot provide proper protection if the person is lying down in the rear seat or if the front seat is in a reclined position.

!WARNING:

Sitting in a reclined position or lying down when your vehicle is in motion can be dangerous. Even if you buckle up, your seat belts can’t do their job when you’re reclined. The shoulder belt can’t do its job because it won’t be against your body. Instead, it will be in front of you. In a crash you could go into it with great force, receiving serious neck or other injuries.

The lap belt can’t do its job either. In a crash the belt could go up over your abdomen. The belt forces

would be applied there, not at your pelvic bones.

This could cause serious internal injuries.

For proper protection when the vehicle is in motion, have the seatback upright. Then sit back in the seat and wear your seat belt properly. See page 1-25.

B160A01A-AAT

CARE OF SEAT BELTS

Seat belt systems should never be disassembled or modified. In addition, care should be taken to assure that seat belts and belt hardware are not damaged by seat hinges, doors or other abuse.

!

WARNING:

When you return the rear seatback to its upright position after the rear seatback was folded down, be careful not to damage the seat belt webbing or buckle. Be sure that the webbing or buckle does not get caught or pinched in the rear seat.

B160B01A-AAT

Periodic Inspection

It is recommended that all seat belts be inspected periodically for wear or damage of any kind. Parts of the system that are damaged should be replaced as soon as possible.

B160C01A-AAT

Keep Belts Clean and Dry

Seat belts should be kept clean and dry. If belts become dirty, they can be cleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not be used because they may damage and weaken the fabric.

B160D01A-AAT

When to Replace Seat Belts

Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an accident. This should be done even if no damage is visible. Additional questions concerning seat belt operation should be directed to your Hyundai

Dealer.

B170A04A-AAT

HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT

(If Installed)

B170A01L

You can adjust the height of the shoulder belt anchor to one of the 4 positions.

If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection. The shoulder portion should be adjusted so that it lies across your chest and midway over your shoulder nearest the door and not your neck.

To adjust the height of the seat belt anchor, lower or raise the height adjuster into an appropriate position. To raise the height adjuster, pull it up. To

FEATURES OF YOUR HYUNDAI 1- 23

lower it, push it down while pressing the height adjuster button.

Release the button to lock the anchor into position. Try sliding the release button to make sure that it has locked into the position.

!WARNING:

o The height adjuster must be in the locked position when the vehicle is moving.

oThe misadjustment of height of the shoulder belt could reduce the effectiveness of the seat belt in a crash.

1- 24 FEATURES OF YOUR HYUNDAI

B180A02A-GAT

SEAT BELTS 3-Point System with Emergency Locking Retractor (If Installed)

To Fasten Your Belt

B180A01NF

To fasten your seat belt, pull it out of the retractor and insert the metal tab into the buckle. There will be an audible «click» when the tab locks into the buckle.

The seat belt automatically adjusts to the proper length only after the lap belt is adjusted manually so that it fits snugly around your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, however, the belt will lock into position. It

will also lock if you try to lean forward too quickly. Check to make sure that the belt is properly locked and that the belt is not twisted.

B260E01TB-GAT

Seat Belt Warning Light

(Except E.C)

The seat belt warning light blinks for about 6 seconds when the ignition key is turned from the «OFF» position to the

«ON».

B265E01TB-GAT

Seat Belt Warning Light and Chime (E.C only)

The seat belt warning light and chime will activate to the following table.

*1) When the ignition key is turned from

«OFF» position to «ON» within 1 minute.

*2) If the vehicle speed exceeds 9km/ h, the seat belt chime also sounds for about 1~2 minutes.

If the vehicle speed is below 9km/h,

1 minute later the seat belt chime also sounds for about 1~2 minutes.

NOTE:

If the driver’s seat belt is operated in this order «unbuckled → buckled → unbuckled → buckled → unbuckled» within 9 seconds after the seat belt is buckled, the seat belt warning light and chime will not activate.

B200A01S-GAT

Adjusting Your Seat Belt

B200A02NF

You should place the belt as low as possible on your hips, not on your waist. If the belt is located too high on your body, you could slide under it in case of accident or a sudden stop. This could result of death, serious injury or property damage. Both arms should not be under or over the belt. Rather, one should be over and the other under, as shown in the illustration.

Never wear the seat belt under the arm nearest the door.

B210A01A-AAT

To Release the Seat Belt

B210A01NF

The seat belt is released by pressing the release button in the locking buckle.

When it is released, the belt should automatically draw back into the retractor.

If this does not happen, check the belt to be sure it is not twisted, then try again.

B220A01A-AAT

SEAT BELTS (2-Point Static

Type) (Rear Seat Center)

(If Installed)

To Fasten Your Seat Belt

B220A04NF

To fasten a 2-point static type belt, insert the metal tab into the locking buckle. There will be an audible «click» when the tab locks into the buckle. Check to make sure the belt is properly locked and that the belt is not twisted.

FEATURES OF YOUR HYUNDAI 1- 25

B220B01A-AAT

Adjusting Your Seat Belt

Too high

Correct

B220B01NF

With a 2-point static type seat belt, the length must be adjusted manually so it fits snugly around your body. Fasten the belt and pull on the loose end to tighten. The belt should be placed as low as possible on your hips, not on your waist. If the belt is too high, it could increase the possibility of your being injured in an accident.

1- 26 FEATURES OF YOUR HYUNDAI

B220C01A-AAT

To Release the Seat Belt

B220C01TB

When you want to release the seat belt, press the button in the locking buckle.

!WARNING:

The center lap belt latching mechanism is different from those for the rear seat shoulder belts. When fastening the rear seat shoulder belts or the center lap belt, make sure they are inserted into the correct buckles to obtain maximum protection from the seat belt system and assure proper operation.

B220D02Y-GAT

SEAT BELTS — Rear Seat Center’s 3-Point System With Emergency Locking Retractor (If installed)

(c)

(a)

(d)

(b)

B220D01TB

1.Before fastening the rear seat center belt, confirm the metal tab (a) and buckle (b) are latched together.

2.After confirming that (a) and (b) are latched, pull the seat belt out of the retractor and insert the metal tab (c) into the buckle (d).

There will be an audible «click» when the tab locks in the buckle. The seat belt automatically adjusts to the proper length only after the lap belt is adjusted manually so that it fits snugly around

B220A02Y-D

your hips. If you lean forward in a slow, easy motion, the belt will extend and let you move around. If there is a sudden stop or impact, the belt will lock into position. It will also lock if you try to lean forward too quickly.

!WARNING:

oWhen using the rear seat center belt, you must lock all metal tabs and buckles. If any metal tab or buckle is not locked, it will increase the chance of injury in the event of collision.

oNever unlock the metal tab (a) and the buckle (b) with the following exceptions.

(1)In case of folding rear seatbacks down.

(2)If transporting an object on the rear seat may cause damage to the rear seat center belt.

oLock the metal tab (a) and the buckle (b) immediately after folding rear seatbacks up.

B220D02TB

oTo disconnect the metal tab (a) from the buckle (b), insert a nar- row-ended tool into the groove located on the buckle (b).

FEATURES OF YOUR HYUNDAI 1- 27

B220C01Y-GAT

To Release the Seat Belt (If installed)

B220C02TB

When you want to release the seat belt, press the button in the locking buckle.

!WARNING:

The center belt latching mechanism is different from those for the rear seat shoulder belts. When fastening the rear seat shoulder belts or the rear seat center belt, make sure they are inserted into the correct buckles to obtain maximum protection from the seat belt system and assure proper operation.

1- 28 FEATURES OF YOUR HYUNDAI

B230A03A-GAT

CHILD RESTRAINT SYSTEM (If Installed)

Children riding in the car should sit in the rear seat and must always be properly restrained to minimize the risk of injury in an accident, sudden stop or sudden maneuver. According to accident statistics, children are safer when properly restrained in the rear seats than in the front seat. Larger children not in a child restraint should use one of the seat belts provided.

You are required by law to use safety restraints for children. If small children ride in your vehicle you must put them in a child restraint system (safety seat). Children could be injured or killed in a crash if their restraints are not properly secured. For small children and babies, a child seat or infant seat must be used. Before buying a particular child restraint system, make sure it fits your car and seat belts, and fits your child.

Follow all the instructions provided by the manufacturer when installing the child restraint system.

!WARNING:

oA child restraint system must be placed in the rear seat. Never install a child or infant seat on the front passenger’s seat.

Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Thus, only use a child restraint in the rear seat of your vehicle.

oSince a safety belt or child restraint system can become very hot if it is left in a closed vehicle, be sure to check the seat cover and buckles before placing a child there.

oWhen the child restraint system is not in use, store it in the luggage compartment or fasten it with a safety belt so that it will not be thrown forward in the case of a sudden stop or an accident.

oChildren who are too large to be in a child restraint should sit in the rear seat and be restrained with the available lap/shoulder belts. Never allow children to ride in the front passenger seat.

oAlways make sure that the shoulder belt portion of the outboard lap/shoulder belt is positioned midway over the shoulder, never across the neck or behind the back. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. The lap belt portion of the lap/ shoulder belt or the center seat lap belt must always be positioned as low as possible on the child’s hips and as snug as possible.

oIf the seat belt will not properly fit the child, Hyundai recommends the use of an approved booster seat in the rear seat in order to raise the child’s seating height so that the seat belt will properly fit the child.

oNever allow a child to stand up or kneel on the seat.

oNever use an infant carrier or child safety seat that «hooks» over a seatback; it may not provide adequate security in an accident.

oNever allow a child to be held in a person’s arms while they are in a moving vehicle, as this could result in serious injury to the child in the event of an accident or a sudden stop. Holding a child in a moving vehicle does not provide the child with any means of protection during an accident, even if the person holding the child is wearing a seat belt.

oIf the child restaint seat is not anchored properly, the risk of a child being seriously injured or killed in a collision greatly increases.

B230G01A-GAT

Child Restraint System Installation on Outboard Rear Seats

B230G01TB

To install a child restraint system in the outboard rear seats, extend the shoulder/lap belt from its retractor. Install the child restraint system, buckle the seat belt and allow the seat belt to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint system and the shoulder portion of the belt is positioned so that it cannot interfere with the child’s head or neck. After installation of the child restraint system, try to move it in all directions to be sure the child restraint system is securely installed.

FEATURES OF YOUR HYUNDAI 1- 29

If you need to tighten the belt, pull more webbing toward the retractor. When you unbuckle the seat belt and allow it to retract, the retractor will automatically revert back to its normal seated passenger emergency locking usage condition.

NOTE:

o Before installing the child restraint system, read the instructions supplied by the child restraint system manufacturer.

oIf the seat belt does not operate as described, have the system checked immediately by your authorized Hyundai dealer.

!WARNING:

Do not install any child restraint system in the front passenger seat. Should an accident occur and cause the passenger side airbag to deploy, it could severely injure or kill an infant or child seated in an infant or child seat. Therefore, only use a child restraint system in the rear seat of your vehicle.

B230B02A-GAT

Using a Child Restraint System with «Tether Anchorage» System

Holder Bolt (5/16″-30 mm)

Washer, Conical Spring

Holder, Child Restraint Hook

Spacer (10mm), Child

Restraint Hook Holder

Retainer Washer

B230B01TB

For small children and babies, the use of a child seat or infant seat is strongly recommended. This child seat or infant seat should be of appropriate size for the child and should be installed in accordance with the manufacturer’s instructions. It is further recommended that the seat be placed in the vehicle’s rear seat since this can make an important contribution to safety. Your vehicle is provided with three child restraint hook holders for installing the child seat or infant seat.

B230E02FC-GAT

Securing a Child Restraint System with «Tether Anchorage» System

Three child restraint hook holders are located on the vertical back panel. (behind rear bumper bar)

1.Route the child restraint seat strap over the seatback.

For vehicles with adjustable headrests, route the tether strap under the headrest and between the headrest posts, otherwise route the tether strap over the top of the seatback.

FEATURES OF YOUR HYUNDAI 1- 31

Covering shelf

Attaching clip

Back panel

Front of Vehicle

B230E01TB

2.Remove the load space cover.

3.Connect the tether strap hook to the child restraint hook holder and tighten to secure the seat.

1- 32 FEATURES OF YOUR HYUNDAI

!WARNING:

To install the Child Restraint Seat, for safety reasons the Seat should be positioned rearmost with the seatback in a vertical position, not reclined.

B230D05E-GAT

Using a Child Restraint System with «ISOFIX» System and «Tether Anchorage» System

HTB193

ISOFIX is a standardised method of fitting child seats that eliminates the need to use the standard adult seat belt to secure the seat in the vehicle. This enables a much more secure and positive location with the added benefit of easier and quicker installation.

An ISOFIX-seat can only be installed if it has vehicle-specific approval in accordance with the requirements of ECE-

R44. For your Hyundai, the Hyundai

ISOFIX GR1 / Hyundai Duo / Römer

ISOFIXGR1andtheRömerDuoISOFIX / Britax Duo ISOFIX is approved ac-

cording to the requirement ECE-R44. This seat has been tested extensively by Hyundai and is recommended for your Hyundai.

NOTE:

At present, this seat is the only one complying with that provision. In case that other manufacturers will furnish proof of a respective certification, Hyundai is going to evaluate this seat carefully and will give a recommendation provided that seat complies to the law. Please ask your Hyundai dealer in this respect.

B230C01TB

On each side of the rear seat, between the cushion and backrest, are located a pair of ISOFIX anchorage points together with a top tether mounting on the luggage compartment. During the installing, the seat has to be engaged at the anchorage-points in a way you can hear it clicking (check by pulling!) and has to be fixed with the Top Tether-belt on the belonging point in the luggagecompartment. The installing and the use of a child-seat has to be done according to the installing-manual, which is added to the ISOFIX-seat.

NOTE:

An ISOFIX-child-seat can only be installed if the seat has a vehiclespecific approval according to ECER44. Before using the ISOFIX-child- seat, which was bought for another car, ask your Hyundai-dealer whether this seat-type is approved and recommended for your Hyundai.

To secure the child restraint seat

B230C02TB

1.To engage the child restraint seat to the ISOFIX anchor, insert the child restraint seat latch into the ISOFIX anchor. Listen for the audible «click» sound.

!CAUTION:

Do not allow the rear seat belt webbing to get scratched or pinched by the ISOFIX-seat latch and ISOFIX anchor during the installation.

FEATURES OF YOUR HYUNDAI 1- 33

2.Connect the tether strap hook to the child restraint hook holder and tighten to secure the seat. Refer to «Securing a Child Restraint System with the

Tether Anchorage System» on page

1-31.

!WARNING:

oDo not install a child restraint seat at the center of the rear seat using the vehicle’s outboard rear seat ISOFIX anchors. The ISOFIX anchors are only provided for the left and right outboard rear seating positions. Do not misuse the ISOFIX anchors by attempting to attach a child restraint seat in the middleoftherearseattotheISOFIX anchors. In a crash, the child restraint seat ISOFIX attachments may not be strong enough to secure the child restraint seat properly in the center of the rear seat and may break, causing serious injury or death.

1- 34 FEATURES OF YOUR HYUNDAI

oWhen using the vehicle’s “ISOFIX” system to install a child restraint system in the rear seat, all unused vehicle rear seat belt metal latch plates or tabs must be latched securely in their seat belt buckles and the seat belt webbing must be retracted behind the child restraint to prevent the child from reaching and taking hold of unretracted seat belts. Unlatched metal latch plates or tabs may allow the child to reach the unretracted seat belts which may result in strangulation and a serious injury or death to the child in the child restraint.

oDo not mount more than one child restraint to a child restraint lower anchorage point. The improper increased load may cause the anchorage points or tether anchor to break, causing serious injury or death.

oAttach the ISOFIX or ISOFIX-com- patible child restraint seat only to the appropriate locations shown in the illustration.

oAlways follow the installation and use instructions provided by the manufacturer of the child restraint.

B180B01A-GAT

Pre-tensioner Seat Belt

(With A/BAG) (If Installed)

Your Hyundai vehicle is equipped with driver’s and front passenger’s pretensioner seat belts. The purpose of the pre-tensioner is to make sure that the seat belts fit tightly against the occupant’s body in certain frontal collisions.

The pre-tensioner seat belts can be activated with the airbags.

HXG229

The pre-tensioner seat belt operates in the same way as an Emergency Locking Retractor (ELR) type of seat belt.

When the vehicle stops suddenly, or if the occupant tries to lean forward too quickly, the seat belt retractor will lock into position. However, in certain frontal collisions, the pre-tensioner will activate and pull the seat belt into tighter contact against the occupant’s body.

3

2

HTB198

The seat belt pre-tensioner system consists mainly of the following components.

Their locations are shown in the illustration.

1.SRS airbag warning light

2.Seat belt pre-tensioner assembly

3.SRS control module

!WARNING:

To obtain maximum benefit from a pre-tensioner seat belt:

1.The seat belt must be worn correctly.

2.The seat belt must be adjusted to the correct position.

NOTE:

o Both the driver’s and front passenger’s pre-tensioner seat belts will be activated in certain frontal collisions. The pretensioner seat belts can be activated with the airbags. The pretensioners will be activated under these conditions even if the seat belts are not being worn at the time of the collision.

oWhen the pre-tensioner seat belts are activated, a loud noise may be heard and fine dust, which may appear to be smoke, may be visible in the passenger compartment. These are normal operating conditions and are not hazardous.

oAlthough it is harmless, the fine dust may cause skin irritation and should not be breathed for prolonged periods. Wash your hands and face thoroughly after an accident in which the pre-tensioner seat belts were activated.

! CAUTION:

oBecause the sensor that activates the SRS airbag is connected with the pre-tensioner seat belt, the SRS

airbag warning light on the instrument panel will blink for approximately 6 seconds after the ignition key has been turned to the «ON» position, and then it should turn off.

oIf the pre-tensioner seat belt is not working properly, this warning light will illuminate even if there is no malfunction of the SRS airbag system . If the SRS airbag warning light does not illuminate when the ignition key is turned to «ON», or if it remains illuminated after blinking for approximately 6 seconds, or if it

FEATURES OF YOUR HYUNDAI 1- 35

illuminates while the vehicle is being driven, please have an authorized Hyundai dealer inspect the pre-tensioner seat belt or SRS airbag system as soon as possible.

!WARNING:

o Pre-tensioners are designed to operate only one time. After activation, pre-tensioner seat belts must be replaced. All seat belts, of any type, should always be replaced after they have been worn during a collision.

oThe pre-tensioner seat belt assembly mechanisms become hot during activation. Do not touch the pre-tensioner seat belt assemblies for several minutes after they have been activated.

oDo not attempt to inspect or replace the pre-tensioner seat belts yourself. This must be done by an authorized Hyundai dealer.

oDo not strike the pre-tensioner seat belt assemblies.

1- 36 FEATURES OF YOUR HYUNDAI

oDo not attempt to service or repair the pre-tensioner seat belt system in any manner.

oImproper handling of the pretensioner seat belt assemblies, and failure to heed the warnings to not strike, modify, inspect, replace, service or repair the pretensioner seat belt assemblies may lead to improper operation or inadvertent activation and serious injury.

oAlways wear the seat belts when driving or riding in a motor vehicle.

B240A02TB-GAT

SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (If Installed)

Driver’s Airbag

B240B01TB

YourHyundaiisequippedwithaSupplemental Restraint (Airbag) System. The indications of the system’s presence are the letters «SRS AIR BAG» embossed on the airbag pad cover in the steering wheel and printed on the passenger’s side front panel pad above the glove box.

The Hyundai SRS consists of airbags installed under the pad covers in the center of the steering wheel and the passenger’s side front panel above the glove box. The purpose of the SRS is to provide the vehicle’s driver and/or the

front passenger with additional protection than that offered by the seat belt system alone, in case of a frontal impact of sufficient severity.

NOTE:

Be sure to read information about the SRS on the labels provided on the backside of the sun visor.

!WARNING:

oAs its name implies, the SRS is designed to work with, and be supplemental to, the driver’s and the passenger’s three point seat belt systems and is not a substitute for them. Therefore your seat belts must be worn at all times while the vehicle is in motion. In addition, the airbags deploy only in certain frontal impact conditions severe enough to cause significant injury to the vehicle occupants.

oThe SRS is designed to deploy the airbags only when an impact is sufficiently severe and when the impact angle is less than 30° from the forward longitudinal axis of the vehicle and will not deploy in side, rear or rollover impacts. Additionally, the airbags will only deploy once. Thus, seat belts must be worn at all times.

Rear impact

Rollover

Side Impact

HTB203

oFront airbags are not intended to deploy in side-impact, rear-im- pact or rollover crashes. In addition, airbags will not deploy in frontal crashes below the deployment threshold speed.

oThe driver should sit back as far as possible while still maintaining control of the vehicle. If you are sitting too close to the airbag, it can cause death or serious injury when it inflates.

oNo objects should be placed over or near the airbag modules on the steering wheel, instrument panel, and the front passenger’s panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to deploy.

oIf the airbags deploy, they must be replaced by an authorized Hyundai dealer.

oDo not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental firing of the airbags or by rendering the SRS inoperative.

oDo not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child

FEATURES OF YOUR HYUNDAI 1- 37

could be severely injured or killed by an airbag deployment in case of an accident.

oDo not allow children to ride in the front passenger seat. If older children (teenagers and older) must ride in the front seat, make sure they are always properly belted and that the seat is moved back as far as possible.

oFor maximum safety protection in all types of crashes, all occupants including the driver should always wear their seat belts whether or not an airbag is also provided at their seating position to minimize the risk of severe injury or death in the event of a crash. Do not sit or lean unnecessarily close to the airbag while the vehicle is in motion.

oThe SRS airbag system must deploy very rapidly to provide protection in a crash. If an occupant is out of position because of not wearing a seat belt, the airbag may forcefully contact the occupant causing serious or fatal injuries.

1- 38 FEATURES OF YOUR HYUNDAI

B240B01FC-GAT

SRS Components and Functions

B240B01L

The SRS consists of the following components:

—Driver’s Airbag Module

—Passenger’s Airbag Module

—SRS Service Reminder Indicator

(SRI)

—SRS Control Module (SRSCM)

The SRSCM continually monitors all elements while the ignition is «ON» to determine if a frontal or near-frontal impact is severe enough to require airbag deployment.

B240B02L

The SRS service reminder indicator

(SRI) on the instrument panel will blink for about 6 seconds after the ignition key is turned to the «ON» position or after the engine is started, after which the SRI should go out.

B240B03L

The airbag modules are located both in the center of the steering wheel and in the front passenger’s panel above the glove box. When the SRSCM detects a considerable impact to the front of the vehicle, it will automatically deploy the airbags.