H310h5 m2 материнская плата инструкция

Содержание

1. Схема подключения к материнской плате
2. Подключение передней панели к материнской плате
3. Шаг 1 – находим шлейфы, идущие от передней панели к мат. плате
4. Шаг 2 – находим контакты на материнской плате для подключения передней панели
5. Шаг 3 – Подключаем фишки разъемов передней панели к соответствующим разъемам материнской платы
6. Вариант первый
7. Вариант второй
8. DP разъем на видеокарте что это?
9. AIO Pump на материнской плате. Что это?
10. eatx12v что это на материнской плате?
11. 7 комментариев
12. Александр
13. КАК ПОДКЛЮЧИТЬ МАТЕРИНСКУЮ ПЛАТУ К ПЕРЕДНЕЙ ПАНЕЛИ КОРПУСА
14. ECS H310CH5-M2: материнская плата для процессоров Intel Coffee Lake
15. Схема подключения разъёмов передней панели компьютера (F_PANEL, F_AUDIO и F_USB)

Инструкция ECS H310H5-M2 доступно в русский?

К сожалению, у нас нет руководства для ECS H310H5-M2, доступного в русский. Это руководство доступно в английский.

Page: 1

H310H5-M2/H310H5-M2DV USER MANUAL
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof
and specifically disclaims any implied warranties of merchantability or fitness for
any particular purpose. The manufacturer reserves the right to revise this publica-
tion and to make changes from time to time in the content hereof without obligation
of the manufacturer to notify any person of such revision or changes.
TrademarkRecognition
Windows®
10/8.1/7 are registered trademarks of Microsoft Corp.
Other product names used in this manual are the properties of their respective owners
and are acknowledged.
FederalCommunicationsCommission(FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits govern-
ing this device. Changes or modifications not expressly approved by the system’s
manufacturer could void the user’s authority to operate the equipment.

Page: 2

ii
H310H5-M2/H310H5-M2DV USER MANUAL
DeclarationofConformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference
that may cause undesired operation.
CanadianDepartmentofCommunications
This class B digital apparatus meets all requirements of the Canadian Interference-
causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouilieur du Canada.
The manual consists of the following:
Describes features of the
motherboard.
page 1
Describes installation of
motherboard components.
page 7
page 25
page 57
Installing the Motherboard
IntroducingtheMotherboard
Provides information on
using the BIOS Setup Utility.
Describes the motherboard
software.
AbouttheManual
Chapter 4
Chapter 1
Chapter 2
Chapter 3
Using BIOS
Using the Motherboard Software
Chapter 5
TroubleShooting
Provides basic trouble
shooting tips.
page 61

Electromagnetic compatibility of multimedia equipment —
Emission requirements
EN 55032
EN 61000-3-2 Electromagnetic Compatibility(EMC)
Part 3-2: Limits-Limits for harmonic current emissions (equipment
input current 16A per phase)
EN 61000-3-3 Electromagnetic Compatibility(EMC)
Part 3-3: Limits-Limitation of voltage changes, voltage fluctuations
and flicker in public low-voltage supply systems, for equipment
with rated current 16A per phase and not subject to conditional
connection
EN 55024 Information technology equipment-Immunity characteristics-
Limits and methods of measurement
EN 60950 Safety for information technology equipment including
electrical business equipment
CE marking






This device is in conformity with the following EC/EMC directives:

Page: 3

iii
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter 2 7
Installing the Motherboard 7
SafetyPrecautions…………………………………………………………………..7
Installing the Motherboard in a Chassis………………………………..7
CheckingJumperSettings………………………………………………………..8
Installing Hardware………………………………………………………..9
Installing the Processor……………………………………………………9
Installing the CPU Cooler…………………………………………………11
Installing Memory Modules…………………………………………….12
Installing Add-on Cards…………………………………………………..13
Connecting Optional Devices…………………………………………..15
Installing a SATA Hard Drive……………………………………………19
ConnectingCaseComponents……………………………………………….20
Front Panel Header………………………………………………………..23
TABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction………………………………………………………………………..1
Package Contents………………………………………………………………..1
Specifications……………………………………………………………………..2
Motherboard Components………………………………………………….4
I/OPorts………………………………………………………………………………….6
Chapter 3 25
UsingBIOS 25
About the Setup Utility……………………………………………………….25
The Standard Configuration…………………………………………….25
Entering the Setup Utility………………………………………………..25
Resetting the Default CMOS Values……………………………….26
Using BIOS…………………………………………………………………………….26
BIOS Navigation Keys……………………………………………………..27
Main Menu…………………………………………………………………..29
Advanced Menu…………………………………………………………….30
Chipset Menu………………………………………………………………..42
Tweak Menu………………………………………………………………….49
Security Menu………………………………………………………………..52
Boot Menu…………………………………………………………………….53
Exit Menu……………………………………………………………………..55

Page: 4

iv
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter 4 57
Using the Motherboard Software 57
Auto-installing under Windows 10………………………………………57
Running Setup……………………………………………………………….57
ManualInstallation………………………………………………………………..59
ECSUtilitySoftware(IntelligentEZUtility)……………………………….59
Chapter 5 61
Trouble Shooting 61
Startupproblemsduringassembly……………………………………….61
Startupproblemsafterprolonguse……………………………………..62
Maintenanceandcaretips……………………………………………………..62
BasicTroubleshootingFlowchart……………………………………………63
UpdatingtheBIOS……………………………………………………………….56

Page: 5

1
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the H310H5-M2/H310H5-M2DV motherboard. This
motherboard is a high performance, enhanced function motherboard designed to
support the LGA1151 socket for Intel®
Coffee Lake processor.
This motherboard is based on Intel®
®
®
®
®
H310 Express Chipset for best desktop platform
solution. It supports up to 32 GB of system memory with dual channel DDR4 2666/
2400 MHz. High resolution graphics via one PCIe x16 Gen3 slot. In addition, one PCI
Express x1 Gen2 slot is for extending usage.
It integrates USB 2.0 and USB 3.1 interface, supporting up to six USB 2.0 ports (four
USB 2.0 ports at the rear panel, one front USB 2.0 header supports additional two
USB 2.0 ports) and four USB 3.1 Gen1 ports (two USB 3.1 Gen1 ports at the rear panel
and one USB 3.1 Gen1 header supports additional two USB 3.1 Gen1 ports).
The motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 keyboard and mouse combo connector, four USB 2.0 ports, one RJ45
LAN connector, two USB 3.1 Gen1 ports, one VGA port, one HDMI port, and audio
jacks for line-in, line-out and microphone.
In addition, this motherboard supports four SATA 6Gb/s connectors for expansion.
Your motherboard package ships with the following items:
Package Contents
H310H5-M2 or H310H5-M2DV Motherboard
User Manual
DVD
I/O Shield
2 SATA 6Gb/s cable





The package contents above are for reference only, please take the actual package items as
standard.

Page: 6

Chapter
1
2
H310H5-M2/H310H5-M2DV USER MANUAL
Specifications
CPU
• Intel®
H310 Chipset
Chipset
• Supported by Intel®
H310 Express Chipset
— 4 x Serial ATA 6Gb/s devices
Storage
• LGA1151 socket for Intel®
Coffee Lake processor
• Supports CPU up to 65W
Note: Please go to ECS website for the latest CPU support list.
• 1 x PS/2 mouse & keyboard combo connector
• 1 x HDMI or DVI (for H310H5-M2DV only) port
• 1 x D-sub port (VGA port)
• 4 x USB 2.0 ports
• 2 x USB 3.1 Gen1 ports
• 1 x RJ45 LAN connector
• 1 x Audio 6-ch jacks (line-in, line-out, microphone)
Rear Panel I/O
LAN • Realtek RTL8111H Gigabit Lan
• Realtek ALC662 6-CH High Definition audio CODEC
— Compliant with HD audio specification
Audio
Expansion
Slots
• 1 x PCI Express x16 Gen3 slot
• 1 x PCI Express x1 Gen2 slot
• Dual-channel DDR4 memory architecture
• 2 x 288-pin DDR4 LONG DIMM sockets support up to 32 GB
• Supports DDR4 2666/2400 MHz DDR4 SDRAM
Memory
Note: Please go to ECS website for the latest Memory support list.
Internal I/O
Connectors &
Headers
• 1 x 24-pin ATX Power Supply connector
• 1 x 4-pin ATX 12V Power connector
• 1 x 4-pin CPU_FAN connector
• 1 x 4-pin SYS_FAN connector
• 1 x Front USB 3.1 Gen1 header (2 Ports)
• 1 x Front USB 2.0 header (2 Ports)
• 4 x SATA 6Gb/s connectors
• 1 x Front Panel audio header
• 1 x Front Panel switch/LED header
• 1 x Trusted platform module header (TPM)
• 1 x Clear CMOS jumper
• 1 x Buzzer header
• 1 x Case open header
• AMI BIOS with 128Mb SPI Flash ROM
• Supports Plug and Play, STR (S3)/ STD (S4), Hardware Monitor
• Audio, LAN, can be disabled in BIOS
• F7 hot key for boot up devices option
• Supports ACPI & DMI
• Supports PgUp clear CMOS Hotkey (PS2 KB Model only)
System BIOS

Page: 7

3
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter
1
• Micro ATX Size, 190mm x 170mm
Form Factor
• Supports eBLU*/eDLU/eSF*
AP Support
Note: *Microsoft .NET Framework 3.5 is required.

Page: 8

Chapter
1
4
H310H5-M2/H310H5-M2DV USER MANUAL
Motherboard Components

Page: 9

5
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter
1
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket LGA1151 socket for Intel®
Coffee Lake processor
2. CPU_FAN 4-pin CPU cooling fan connector
3. SYS_FAN 4-pin system cooling fan connector
4. DIMM1~2 288-pin DDR4 Module slots
5. ATX_POWER Standard 24-pin ATX power connector
6. SATA3_1~4 Serial ATA 6Gb/s connectors
7. BZ Buzzer header
8. F_PANEL Front panel switch/LED header
9. TPM Trusted platform module header
10. F_USB1 Front panel USB 2.0 header
11. CASE CASE open header
12. BT Battery
13. PCIEX16 PCI Express x16 slot Gen3 for graphics interface
14. CLR_CMOS Clear CMOS jumper
15. F_AUDIO Front panel audio header
16. PCIEX1_1 PCI Express Gen2 x1 slot
17. USB3F Front panel USB 3.1 Gen1 header
18. ATX_12V 4-pin +12V power connector

Page: 10

Chapter
1
6
H310H5-M2/H310H5-M2DV USER MANUAL
I/O Ports
1. PS/2 Mouse & Keyboard Combo Connector (green/purple)
Use the PS/2 port to connect the PS/2 Mouse or Keyboard.
2. USB 2.0 Ports
Use the USB 2.0 ports to connect USB 2.0 devices.
3. HDMI or DVI Port
You can connect the display device to the HDMI or DVI port.
4. VGA Port
Connect your monitor to the VGA port.
5. USB 3.1 Gen1 Ports
Use the USB 3.1 Gen1 ports to connect USB 3.1 devices.
6. LAN Port
Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
7. Line-in (blue)
It can be connected to an external CD/DVD player, Tape player or other audio
devices for audio input.
8. Line-out (lime)
It is used to connect to speakers or headphones.
9.Microphone (pink)
It is used to connect to a microphone.
LAN LED Status Description
OFF No data
Orange blinking Active
OFF No link
Green Link
ActivityLED
LinkLED
Link LED
LAN Port
Or

Page: 11

Chapter
2
7
H310H5-M2/H310H5-M2DV USER MANUAL
Chapter 2
Installing the Motherboard
2-1. Safety Precautions
2-2. Installing the motherboard in a Chassis
This motherboard carries a Mini ITX form factor of 190 x 170 mm. Choose a chassis
that accommodates this from factor. Make sure that the I/O template in the chassis
matches the I/O ports installed on the rear edge of the motherboard. Most system
chassis have mounting brackets installed in the chassis, which corresponds to the
holes in the motherboard. Place the motherboard over the mounting brackets and
secure the motherboard onto the mounting brackets with screws.
Follow these safety precautions when installing the motherboard:
• Wear a grounding strap attached to a grounded device to avoid damage
from static electricity.
• Discharge static electricity by touching the metal case of a safely grounded
object before working on the motherboard.
• Leave components in the static-proof bags.
• Always remove the AC power by unplugging the power cord from the power
outlet before installing or removing the motherboard or other hardware
components.
Do not over-tighten the screws as this can stress the motherboard.

Page: 12

Chapter
2
8
H310H5-M2/H310H5-M2DV USER MANUAL
The following illustration shows the location of the motherboard jumpers. Pin 1 is
labeled.
To avoid the system instability after clearing CMOS, we recommend users to
enter the main BIOS setting page to “Load Default Settings” and then “Save
and Exit Setup”.
2-3. Checking Jumper Settings
1. CLR_CMOS: Clear CMOS Jumper
Connect a serial port extension bracket to this header to add a serial port to your
system.

Page: 13

Chapter
2
9
H310H5-M2/H310H5-M2DV USER MANUAL
2-4. Installing Hardware
2-4-1. Installing the Processor
• This motherboard has an LGA1151 socket.
• When choosing a processor, consider the performance requirements of
the system. Performance is based on the processor design, the clock speed
and system bus frequency of the processor, and the quantity of internal
cache memory and external cache memory.
• You may be able to change the settings in the system Setup Utility. We
strongly recommend you do not over-clock processor or other
components to run faster than their rated speed.
• The following illustration shows CPU installation components.
A. Press the hook of lever down with your thumb and pull it to the right
side to release it from retention tab.
B. Lift the tail of the load lever and rotate the load plate to fully open
position.
C. Grasp the edge of the package substrate. Make sure pin 1 indicator
is on your bottom-left side. Aim at the socket and place the package
carefully into the socket by purely vertical motion.

Page: 14

Chapter
2
10
H310H5-M2/H310H5-M2DV USER MANUAL
D. Rotate the load plate onto the package IHS (Intergraded Heat
Spreader). Engage the load lever while pressing down lightly onto the
load plate. Secure the load lever with the hook under retention tab. Then
the cover will flick automatically.
Please save and replace the cover onto the CPU socket if processor is re-
moved.

Page: 15

Chapter
2
11
H310H5-M2/H310H5-M2DV USER MANUAL
A. Apply some thermal grease onto the contacted area between the
heatsink and the CPU, and make it to be a thin layer.
B. Fasten the cooling fan supporting base onto the CPU socket on the
motherboard. And make sure the CPU fan is plugged to the CPU fan
connector.
C. Connect the CPU cooler power connector to the CPU_FAN connector.
2-4-2. Installing the CPU Cooler
• Install the cooling fan in a well-lit work area so that you can clearly see the
motherboard and processor socket.
• Avoid using cooling fans with sharp edges in case the fan casing and the
clips cause serious damage to the motherboard or its components.
• To achieve better airflow rates and heat dissipation, we suggest that you
use a high quality fan with 3800 rpm at least. CPU fan and heat sink instal-
lation procedures may vary with the type of CPU fan/heatsink supplied.
The form and size of fan/heatsink may also vary.
• DO NOT remove the CPU cap from the socket before installing a CPU.
• Return Material Authorization (RMA) requests will be accepted only if the
motherboard comes with the cap on the LGA1151 socket.
• The following illustration shows how to install CPU fan.

Page: 16

Chapter
2
12
H310H5-M2/H310H5-M2DV USER MANUAL
2-4-3. Installing Memory Modules
• This motherboard accommodates two memory modules. It can support
two 288-pin DDR4 2666/2400 MHz.
• Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always wear
a grounding strap when you handle the modules.
• You must install at least one module in any of the two slots. Total memory
capacity is 32 GB.
• Refer to the following to install the memory modules.
C. The slot latches are levered upwards and latch on to the edges of the
DIMM.
A. Push the latches on each side of the DIMM slot down.
B. Install the DIMM module into the slot and press it firmly down until it
seats correctly. Check that the cutouts on the DIMM module edge
connector match the notches in the DIMM slot.

Page: 17

Chapter
2
13
H310H5-M2/H310H5-M2DV USER MANUAL
2-4-4. Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect
them to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can
increase the motherboard’s capabilities by adding hardware that performs tasks
that are not part of the basic system.
Before installing an add-on card, check the documentation for
the card carefully. If the card is not Plug and Play, you may have
to manually configure the card before installation.
PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI
Express graphics card that is fully compliant to the PCI Express
Base Specification revision 3.0.
The PCI Express x1 slot is fully compliant to the PCI Express Base
Specification revision 2.0.
PCIEX1_1 Slot
Follow these instructions to install an add-on card:
1 Remove a blanking plate from the system case corresponding to the slot
you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network
adapters, you have to install drivers and software before you can begin using
the add-on card.

Page: 18

Chapter
2
14
H310H5-M2/H310H5-M2DV USER MANUAL
Install the VGA Card in the PCIE X16 slot
Please refer the following illustrations to install the add-on card:

Page: 19

Chapter
2
15
H310H5-M2/H310H5-M2DV USER MANUAL
2-4-5. Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional
devices:
No. Components No. Components
1 F_USB1 4 SATA3_1~4
2 TPM 5 F_AUDIO
3 CASE 6 USB3F
The motherboard has one USB 2.0 header supporting two USB 2.0 ports.
Additionally, some comuter cases have USB ports at the front of the case. If you have
this kind of case, use auxiliary USB connector to connect the front-mounted ports to
the motherboard.
1. F_USB1: 2*5-pin Front Panel USB 2.0 header

Page: 20

Chapter
2
16
H310H5-M2/H310H5-M2DV USER MANUAL
2. TPM: Trusted Platform Module Header
Trusted platform module (TPM) is a published specification detailing a
microcontroller that can store secured information, and implementations of that
specification.
3. CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis
equipped with instrusion detection switch and needs to be enabled in BIOS.

Page: 21

Chapter
2
17
H310H5-M2/H310H5-M2DV USER MANUAL
SATA3_1~4 connectors are used to support the Serial ATA 6Gb/s device, simpler disk
drive cabling and easier PC assembly. It eliminates limitations of the current
Parallel ATA interface. But maintains register compatibility and software
compatibility with Parallel ATA.
4. SATA3_1~4: Serial ATA Connectors
The front panel audio header allows the user to install auxiliary front-oriented
microphone and line-out ports for easier access. This header supports HD audio by
default. If you want connect an AC’ 97 front panel audio to HD onboard headers,
please set as below picture.
5. F_AUDIO: Front Panel Audio Header

Page: 22

Chapter
2
18
H310H5-M2/H310H5-M2DV USER MANUAL
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or system
hang-up.
This Motherboard implements one USB 3.1 Gen1 header supporting 2 extra front
USB 3.1 Gen1 ports, which delivers 5Gb/s transfer rate.
6. USB3F: Front Panel USB 3.1 Gen1 Header

Page: 23

Chapter
2
19
H310H5-M2/H310H5-M2DV USER MANUAL
2-4-6. Installing a SATA Hard Drive
About SATA Connectors
Your motherboard features four SATA connectors supporting a total of four drives.
SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface
for the IDE hard drives which are currently used in most PCs. These connectors are
well designed and will only fit in one orientation. Locate the SATA connectors on the
motherboard and follow the illustration below to install the SATA hard drives.
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial
ATA protocol. This SATA cable comes with a SATA power cable. You can connect either
end of the SATA cable to the SATA hard drive or the connector on the motherboard.
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard.
2 Attach the other cable end to the SATA hard drive.
3 Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
* For reference only
Installing Serial ATA Hard Drives
This section describes how to install a SATA Hard Drive.

Page: 24

Chapter
2
20
H310H5-M2/H310H5-M2DV USER MANUAL
No. Components No. Components
1 CPU_FAN 4 BZ
2 SYS_FAN 5 F_PANEL
3 ATX_POWER 6 ATX12V
After you have installed the motherboard into a case, you can begin connecting the
motherboard components. Refer to the following:
2-4-7. Connecting Case Components
1. CPU_FAN (CPU Cooling FAN Power Connector) & 2. SYS_FAN (System Cooling
FAN Power Connector)
Connect the CPU cooling fan cable to CPU_FAN.
Users please note that the fan connector supports the CPU cooling fan of 1.1A
~ 2.2A (26.4W max) at +12V.
Connect the system cooling fan connector to SYS_FAN.

Page: 25

Chapter
2
21
H310H5-M2/H310H5-M2DV USER MANUAL
3. ATX_POWER (ATX 24-pin Power Connector) & 6. ATX12V (ATX 12V Power
Connector)
Connect the standard power supply connector to ATX_POWER.
Connect the auxiliary case power supply connector to ATX12V.
The ATX 24-pin connector allows you to connect to ATX_POWER power supply.
With ATX_POWER power supply, users
please note that when installing 24-pin
power cable, the latches of power cable
and the ATX_POWER match perfectly.
Connecting 24-pin power cable
24-pin power cable
The ATX12V power connector is used to provide power to the CPU.
When installing 4-pin power cable, the
latches of power cable and the ATX12V
match perfectly.
Connecting 4-pin power cable
4-pin power cable

Page: 26

Chapter
2
23
H310H5-M2/H310H5-M2DV USER MANUAL
This concludes Chapter 2. The next chapter covers the BIOS.
5. F_PANEL: Front Panel Header
The front panel header (F_PANEL) provides a standard set of switch and LED headers
commonly found on Mini ITX case. Refer to the table below for information:
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that
data is being read from or written to the hard drive. For the LED to function properly,
an IDE drive should be connected to the onboard IDE interface. The LED will also
show activity for devices connected to the SCSI (hard drive activity LED) connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides
power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-
contact switch that is normally open. When the switch is closed, the board resets
and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momen-
tary-contact switch that is normally open. The switch should maintain contact for at
least 50 ms to signal the power supply to switch on or off. The time requirement is
due to internal de-bounce circuitry. After receiving a power on/off signal, at least
two seconds elapses before the power supply recognizes another on/off signal.

Page: 27

Chapter
2
24
H310H5-M2/H310H5-M2DV USER MANUAL
Memo

Page: 28

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 25
• Hard drives, diskette drives and peripherals
• Video display type and display options
• Password protection from unauthorized use
• Power Management features
About the Setup Utility
The computer uses the latest “American Megatrends Inc. ” BIOS with support for
Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup
instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s con-
figuration status and provides you with options to set system parameters. The pa-
rameters are stored in battery-backed-up CMOS RAM that saves this information
when the power is turned off. When the system is turned back on, the system is
configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
The settings made in the Setup Utility affect how the computer performs. Before
using the Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we rec-
ommend that you read this chapter in case you need to make any changes in the
future.
This Setup Utility should be used:
• when changing the system configuration
• when a configuration error is detected and you are prompted to make
changes to the Setup Utility
• when trying to resolve IRQ conflicts
• when making changes to the Power Management configuration
• when changing the password or making other changes to the Security
Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines.
POST is a series of built-in diagnostics performed by the BIOS. After the POST routines
are completed, the following message appears:
Press DEL to enter SETUP
Chapter 3
Using BIOS

Page: 29

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
26
Press the delete key to access BIOS Setup Utility.
Resetting the Default CMOS Values
When powering on for the first time, the POST screen may show a “CMOS Settings
Wrong” message. This standard message will appear following a clear CMOS data
at factory by the manufacturer. You simply need to Load Default Settings to reset
the default CMOS values.
Note: Changes to system hardware such as different CPU, memories, etc. may
also trigger this message.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the
Setup Utility displays a list of the options that are available. A highlight indicates
which option is currently selected. Use the cursor arrow keys to move the highlight
to other options. When an option is highlighted, execute the option by pressing
<Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for
information.
Some options (marked with an icon ) lead to submenus that enable you to change
the values for the option. Use the cursor arrow keys to scroll through the items in the
submenu.

Page: 30

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 27
The default BIOS setting for this motherboard apply for most conditions
with optimum performance. We do not suggest users change the default
values in the BIOS setup and take no responsibility to any damage caused
by changing the BIOS settings.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY FUNCTION
 Scrolls through the items on a menu
+/-Change Opt.
F2 Previous Value
F3 Optimized Defaults
F1 General Help
ESC Exits the current menu


Enter Select
In this manual, default values are enclosed in parenthesis. Submenu items are
denoted by an icon .
F4 Save & Exit
1. For the purpose of better product maintenance, the manufacture
reserves the right to change the BIOS items presented in this manual. The
BIOS setup screens shown in this chapter are for reference only and may
differ from the actual BIOS. Please visit the manufacture’s website for
updated manual.
2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select
item; Double click: enter; Right click: exit.
Default
Select the default icon and press <Enter> or double click the left key of the mouse
to display the screen. Then you can load optimized defaults or not.

Page: 31

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
28
Advanced
Select the advanced icon and press <Enter> or double click the left key of the mouse
to display the screen.
Exit
Select the exit icon and press <Enter> or double click the left key of the mouse to
display the screen.

Page: 32

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 29
Main Menu
System Date & Time
The Date and Time items show the current date and time on the computer. If you are
running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
System Language (English)
This item is used to set system language.
This menu shows the information of BIOS and enables you to set the system
language, date and time.
Choosethesystemdefault
language
Main Advanced Chipset Tweak Security Boot Exit
BIOSInformation
System Language English
System Date Wed 11/15/2017
SystemTime 17:18:11
BIOS Version 17.11.15
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
BIOS Version (17.11.15)
This item shows the BIOS version.

Page: 33

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
30
LAN Configuration
The item in the menu shows the LAN-related information that the BIOS
automatically detects.
Onboard LAN Controller (Enabled)
Use this item to enable or disable Onboard LAN controller.
Press <Esc> to return to the Advanced Menu page.
Main Advanced Chipset Tweak Security Boot Exit
LAN Configuration
Onboard LAN Controller Enabled
Enabled/Disabled Onboard
LAN Controller
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
The Advanced menu items allow you to change the settings for the CPU and other
system.
Advanced Menu
LAN Configuration
Parameters
Main Advanced Chipset Tweak Security Boot Exit
LAN Configuration
PC Health Status
PowerManagementSetup
ACPI Settings
CPU Configuration
SATA Configuration
USB Configuration
Super IO Configuration
Trusted Computing +/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit

Page: 34

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 31
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the
parameters for critical voltages, temperatures and fan speeds.
Scroll to this item and press <Enter> to view the following screen:
 Smart Fan Function
Main Advanced Chipset Tweak Security Boot Exit
SmartFan Select
Main Advanced Chipset Tweak Security Boot Exit
Smart Fan Select System
Smart Fan Mode Normal
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
Smart Fan start PWM value 180
Smart Fan start PWM TEMP (DTS) 70
DeltaT 3
Smart Fan Slope PWM value 10
Fan Full Speed Offset (DTS) 77
CPU Temperature (DTS) 46
SystemTemperature 27O
C
CPU Fan Speed 0 RPM
SystemFan Speed 2008 RPM
Core Voltage 1.012V
DIMM Voltage
1.188V+12V 12.4080V
+5VSB 5.038V
+VCC 5.137V
TCCActivation Temperature (DTS) 100
Smart Fan Function
PC Health Status
Smart Fan Select (System)
This item allows you to change and configure Smart Fans on M/B. ex. CPU Fan, System
Fan.

Page: 35

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
32
Smart Fan Mode (Normal)
This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a
better operation environment. If you choose Normal mode, the fan speed will be
auto adjusted depending on the CPU temperature. If you choose Quite mode, the
fan speed will be auto minimized for quiet environment. If you choose Silent mode,
the fan speed will be auto restricted to make system more quietly. If you choose
Manual mode, the fan speed will be adjust depending on users’ parameters.
Smart Fan start PWM value (180)
Smart Fan start PWM TEMP (DTS) (70)
This item is used to set the start PWM value of the smart fan.
This item is used to set the start temperature of the smart fan.
DeltaT (3)
This item specifies the range that controls CPU temperature and keeps it from going
so high or so low when smart fan works.
Smart Fan Slope PWM value (10)
This item is used to set the Slope Select PWM of the smart fan.
This item is used to set the fan full speed offset value.
Fan Full Speed Offset (DTS) (77)
Press <Esc> to return to the PC Health Status page.
• CPU Temperature (DTS)
• System Temperature
• CPU Fan Speed
• System Fan Speed
• Core Voltage
• DIMM Voltage
• +12V
• +5VSB
• +VCC
System Component Characteristics
These items display the monitoring of the overall inboard hardware health events,
such as CPU & DIMM voltage, CPU & System fan speed…etc.
Press <Esc> to return to the Advanced Menu page.
TCC Activation Temperature (DTS) (100)
This item shows the factory TCC activation temperature.

Page: 36

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 33
Power Management Setup
This page sets up some parameters for system power management operation.
Resume By PME (Disabled)
The system can be turned off with a software command. If you enable this item, the
system can automatically resume if there is an incoming call on the PCI/PCI-E
Modem or PCI/PCI-E LAN card. You must use an ATX power supply in order to use this
feature. Use this item to do wake-up action if inserting the PCI/PCI-E card.
Resume By USB (Disabled)
This item allows you to enable or disable the USB device wakeup function from S3
mode.
Main Advanced Chipset Tweak Security Boot Exit
About Resume by PCI/PCI-E/
LAN/Ext.USB3.xPME
Resume By RTC Alarm (Disabled)
The system can be turned off with a software command. If you enable this item, the
system can automatically resume at a fixed time based on the system’s RTC
(realtimeclock). Use the items below this one to set the date and time of the
wake-up alarm. You must use an ATX power supply in order to use this feature.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
EUP Function (Enabled)
This item allows user to enable or disable EUP support.
Power LED Type (Dual Color LED)
This item shows the type of the Power LED.
Press <Esc> to return to the Advanced Menu page.
Resume By PS2 MS (Disabled)
This item allows you to enable or disable the mouse activity to awaken the system
from power saving mode.
Resume By PS2 KB (Disabled)
This item allows you to enable or disable the keyboard activity to awaken the
system from power saving mode.
PowerManagementSetup
Resume By PME Disabled
ResumeByUSB Disabled
ResumeByPS2KB Disabled
Resume By PS2 MS Disabled
Resume By RTC Alarm Disabled
EUP Function Enabled
PowerLEDType Dual Color LED

Page: 37

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
34
ACPI Settings
The item in the menu shows the highest ACPI sleep state when the system enters
suspend.
ACPI Sleep State [S3(Suspend to RAM)]
This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).
Press <Esc> to return to the Advanced Menu page.
Main Advanced Chipset Tweak Security Boot Exit
SelectthehighestACPIsleep
state the system will enter
whentheSUSPENDbuttonis
pressed.
ACPI Settings
ACPI Sleep State S3 (Suspend to RAM)
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit

Page: 38

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 35
CPU Configuration
The item in the menu shows the CPU.
Intel(R) Core(TM) i7-8700T CPU @ 3.20GHz
This is display-only field and displays the information of the CPU installed in your
computer.
Processor Speed (3200MHz)
This item shows the current processor speed.
ID (0x906EA)
This item shows the processor ID.
Microcode Revision (70)
This item shows the Microcode version.
Number of Processors (6Core(s) / 12Thread(s))
This item shows the core number of the processor.
VMX (Supported)
This item shows the CPU Support Intel VMX(Virtual-Machine Extensions) Technology.
Main Advanced Chipset Tweak Security Boot Exit
Enabled for Windows XP
and Linux (OS optimized for
Hyper-ThreadingTechnology)
andDisabledforotherOS(OS
not optimized for
Hyper-Threading Technology).
Active Processor Cores (All)
Use this item to control the number of active processor cores.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
CPU Configuration
Intel(R) Core(TM) i7-8700T CPU @ 3.20GHz
Processor Speed 3200 MHz
ID 0x906EA
Microcode Revision 70
Number of Processors 6Core(s) / 12Thread(s)
VMX Supported
SMX/TXT Supported
Hyper-Threading Enabled
Active Processor Cores All
Limit CPUID Maximum Disabled
Intel(VMX) Virtualization Technology Enabled
Package C State limit AUTO
Enhanced Halt (C1E) Enabled
Intel(R) Speed ShiftTechnology Enabled
SMX/TXT (Supported)
This item shows the computer support Intel SMX/TXT Technology.
Limit CPUID Maximum (Disabled)
Use this item to enable or disable the maximum CPUID value limit, you can enables
this item to prevent the system from “rebooting” when trying to install Windows NT
4.0.
Hyper-Threading (Enabled)
This item is only available when the chipset supports Hyper-Threading and you are
using a Hyper-Threading CPU.

Page: 39

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
36
Intel (VMX) Virtualization Technology (Enabled)
When disabled, a VMM cannot utilize the additional hardware capabilities provided
by Vandorpool Technology.
Package C State limit (AUTO)
Use this item to set the package C state limit.
Press <Esc> to return to the Advanced Menu page.
Enhanced Halt (C1E) (Enabled)
Use this item to enable the CPU energy-saving function when the system is not
running.
Intel(R) Speed Shift Technology (Enabled)
Use this item to enable or disable the Intel(R) Speed Shift Technology.

Page: 40

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 37
SATA Configuration
Use this item to show the mode of serial SATA configuration options.
SATA Mode (AHCI)
Use this item to select SATA mode.
Determines how SATA
controller(s) operate.
Main Advanced Chipset Tweak Security Boot Exit
SATA Port 1~4 (Not Present/TOSHIBA Q300. (120.0GB))
This motherboard supports four SATA channels, each channel allows one SATA device
to be installed. Use these items to configure each device on the SATA channel.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
SATAConfiguration
SATAMode AHCI
SATAPort1
Not Present
SATAPort2
Not Present
SATAPort3
Not Present
SATAPort4
TOSHIBA Q300. (120.0GB)
Press <Esc> to return to the Advanced Menu page.

Page: 41

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
38
All USB Devices (Enabled)
Use this item to enable or disable all USB devices.
USB Configuration
Use this item to show the information of USB configuration.
Legacy USB Support (Enabled)
Use this item to enable or disable support for legacy USB devices.
Main Advanced Chipset Tweak Security Boot Exit
USB Support Parameters
USB Configuration
All USB Devices Enabled
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
Legacy USB Support Enabled
Press <Esc> to return to the Advanced Menu page.

Page: 42

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 39
Use this item to show the information of Super IO configuration.
Super IO Configuration
Super IO Chip (IT8613)
This item shows the information of the super IO chip.
Main Advanced Chipset Tweak Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
Super IO Configuration
Super IO Chip IT8613
Press <Esc> to return to the Advanced Menu page.

Page: 43

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
40
Use this item to show the information of trusted computing configuration.
Trusted Computing
Enables or Disables BIOS
support for security device.
O.S. will not show Security
Device.TCGEFIprotocoland
INT1A interface will not be
available.
Main Advanced Chipset Tweak Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
TPM20 Device Found
Vendor: INTC
Firmware Version: 401.1
TPM Support Enabled
Active PCR banks SHA-1, SHA256
Available PCR banks SHA-1, SHA256
SHA-1 PCR bank Enabled
SHA256 PCR bank Enabled
Pending opreation None
Platform Hierarchy Enabled
Storage Hierarchy Enabled
Endorsement Hierarchy Enabled
TPM2.0 UEFI Spec Version TCG_2
Physical Presence Spec Version 1.3
TPM 20 InterfaceType CRB
TPM Support (Enabled)
Use this item to enable or disable the TPM port. O.S. will not show TPM. Reset of
platform is required.
Active PCR banks (SHA-1, SHA256)
Use this item to show the Active PCR banks.
Available PCR banks (SHA-1, SHA256)
Use this item to show the Available PCR banks.
Platform Hierarchy (Enabled)
Use this item to enable or disable the Platform Hierarchy.
Storage Hierarchy (Enabled)
Use this item to enable or disable the Storage Hierarchy.
Endorsement Hierarchy (Enabled)
Use this item to enable or disable the Endorsement Hierarchy.
TPM2.0 UEFI Spec Version (TCG_2)
Use this item to show the TPM2.0 UEFI Spec Version.
Physical Presence Spec Version (1.3)
Use this item to show the Physical Presence Spec Version.
SHA-1 PCR Bank (Enabled)
Use this item to enable or disable the SHA-1 PCR bank.
SHA256 PCR Bank (Enabled)
Use this item to enable or disable the SHA256 PCR bank.
Pending operation (None)
Schedule an Operation for the Security Device. NOTE: Your Computer will reboot
during restart in order to change State of Security Device.

Page: 44

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 41
Press <Esc> to return to the Advanced Menu page.
TPM 20 InterfaceType (CRB)
Use this item to show the TPM 20 InterfaceType.

Page: 45

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
42
The chipset menu items allow you to change the settings for the North Bridge
chipset, South Bridge chipset and other system.
Chipset Menu
DVMT/FIXED Memory (256M)
When set to DVMT Mode, the graphics chip will dynamically allocate system memory
as graphics memory, according to system and graphics requirements.
System Agent Configuration
Scroll to this item and press <Enter> to view the following screen:
System Agent (SA)
Parameters
Main Advanced Chipset Tweak Security Boot Exit
System Agent Configuration
PCH Configuration
ME Configuration
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
IGD Memory (64M)
This item shows the information of the IGD (Internal Graphics Device) memory.
Main Advanced Chipset Tweak Security Boot Exit
Select which of IGFX/PEG/
PCI Graphics device should
be Primary Display Or select
SG for Switchable Gfx.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
System Agent Configuration
Initiate Graphic Adapter Auto
IGD Memory 64M
DVMT/FIXED Memory 256M
IGD Multi-Monitor Disabled
Initiate Graphic Adapter (Auto)
This item allows you to select graphics controller to use as the primary boot device.

Page: 46

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 43
IGD Multi-Monitor (Disabled)
This item allows you to enable or disable the IGD Multi-Monitor.
Press <Esc> to return to the Chipset Menu page.
Multi-Monitor technology
Please note that Multi-Monitor technology supports up to four monitors:
one or two Intel integrated Graphics and one or two PCI-Express graphics
devices under Windows 10.
Multi-Monitor technology can help you to increase the area available for programs
running on a single computer system through using multiple display devices.
It is not only to increase larger screen viewing but also to improving personal
productivity.
Step 1. Insert ECS drives DVD to run Auto setup or browse the DVD to install Intel
chipset drivers, VGA and sound drivers.(If you want know the detail information,
please refer to chapter 4.)
Intel Integrated Graphics PCI-Express Graphics

Page: 47

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
44
Step 3. Enable IGD Multi-Monitor from BIOS. In the following BIOS screen, please set
IGD Multi-Monitor to [Enabled].
Step 2. Install all the drivers of PCI-Express graphic cards. Click the Browse CD item,
then appears the following screen. Select the driver you want to install(e.g NVIDIA
GeForce 8400 GS(Microsoft Corporation-WDDM v1.1)) and double click it.
Main Advanced Chipset Tweak Security Boot Exit
Select which of IGFX/PEG/
PCI Graphics device should
be Primary Display Or select
SG for Switchable Gfx.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit
System Agent Configuration
Initiate Graphic Adapter Auto
IGD Memory 64M
DVMT/FIXED Memory 256M
IGD Multi-Monitor Enabled

Page: 48

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 45
2.Select display devices, set the multiple displays option and to extend desktop for
display “Multi-Monitor technology”.
Change the appearance of your displays
Control Panel All Control Panel Items Display Screen Resolution Search Control Panel
1
3 4
Detect
Identify
3. DELL U2410
Display:
Resolution: 1920×1200(recommended)
Orientation: Landscape
Disconnect this display
Multiple displays:
Make this my main display Advance settings
Make text and other items larger or smaller
What display settings should I choose?
OK Cancel Apply
2
You must selectApply before making additional changes.
!
Extenddesktoptothisdisplay
Disconnect this display
Step 4. Change the appearance of your displays under Windows 10.
Change the appearance of your displays
Control Panel All Control Panel Items Display Screen Resolution Search Control Panel
1
2 3 4
Detect
Identify
1. DELL U2410
Display:
Resolution: 1920×1200(recommended)
Orientation: Landscape
Extenddesktoptothisdisplay
Multiple displays:
This is currently your main display. Advance settings
Make text and other items larger or smaller
What display settings should I choose?
OK Cancel Apply
Show the path of the setting location
Display devices
The type of the display
Set the multiple displays
1. Enter the Control Panel menu, select the Display in the All Control Panel Items
and click the Screen Resolution, then appears the following screen.

Page: 49

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL
46
Change the appearance of your displays
Control Panel All Control Panel Items Display Screen Resolution Search Control Panel
1
Detect
Identify
4.AL1717
Display:
Resolution: 1920×1200(recommended)
Orientation: Landscape
Disconnect this display
Multiple displays:
Make this my main display Advance settings
Make text and other items larger or smaller
What display settings should I choose?
OK Cancel Apply
2
You must selectApply before making additional changes.
!
3 4
3
Change the appearance of your displays
Control Panel All Control Panel Items Display Screen Resolution Search Control Panel
1
Detect
Identify
4.AL1717
Display:
Resolution: 1920×1200(recommended)
Orientation: Landscape
Extenddesktoptothisdisplay
Multiple displays:
Make this my main display Advance settings
Make text and other items larger or smaller
What display settings should I choose?
OK Cancel Apply
2
You must selectApply before making additional changes.
!
3 4

Page: 50

Chapter
3
H310H5-M2/H310H5-M2DV USER MANUAL 47
PCH Configuration
Scroll to this item and press <Enter> to view the following screen:
Restore AC Power Loss (Power Off)
This item enables your computer to automatically restart or return to its operating
status.
Azalia HD Audio (Enabled)
This item enables or disables Azalia HD audio.
Case Open Warning (Disabled)
This item enables or disables the warning if the case is opened up, and the item
below indicates the current status of the case.
Chassis Opened (No)
This item indicates whether the case has been opened.
Press <Esc> to return to the Chipset Menu page.
Main Advanced Chipset Tweak Security Boot Exit
Select AC power state when
power is re-applied after
a power failure.
PCH Configuration
Restore AC Power Loss Power Off
Audio Configuration
Azalia HD Audio Enabled
Case Open Warning Disabled
Chassis Opened No +/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help
F2: Previous Values
F3:OptimizedDefaults
F4:Save&Exit
ESC/Right Click: Exit