Futaba 14mz инструкция на русском

Never remove the CF card or turn off power while entering data.

Never store the CF card where it may be subject to strong static electricity or magnetic fields.

Do not expose the CF card to direct sunlight, excessive humidity or corrosive environments.

Do not expose the CF card to dirt, moisture, water or fluids of any kind.

Always hold the CF card by the edges during installation and removal.

Be certain to insert the CF card in the correct direction.

•T14MZ Transmitter, including RF module (MZ-DDS)

•R5014 Receiver

•CFDP32M Data-Pack (CF card)

•LT2F2200 Li-ion battery & LBC-1D5 Charger

•NR4F1500 Ni-Cd battery & 110V wall charger (North America)

•Switch harness/Aileron extension cord/Y-harness/DSC cord

•Tool Box (includes special jig for adjustment)

•Neck strap

•Frequency Flag

The set contents depend on the type of set.

Transmitter T14MZAP/HP

Operating system: 2-stick, 14 channels, PCM-G3, synthesizer system

Transmitting frequency: US only 72 or 50 MHz bands

Modulation: PCM — G3, PCM1024, or FM/PPM switchable.

Power supply: 7.4V LT2F2200 Li-ion battery

Current drain: 1 ampere maximum (RF power on and back light on) 700mA average

Receiver R5014DPS

(PCM-G3, Synthesizer, Dual conversion)

Receiving frequency: US only 72 or 50 MHz bands Intermediate freq.: 10.7 MHz & 450 kHz

Power requirement: 4.8 V Ni-Cd battery Current drain: 75 mA

Size: 52×37.5×16.5 mm Weight: 33 g. Channels: 14

Suggested Servos for use with your 14MZ Servo S9154 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral Power requirement: 4.8 V (from receiver)

Output torque: 63.9 oz.-in. (4.6 kg-cm) at 4.8V Operating speed: 0.14 sec/60 at 4.8V

Size: 1.87 x 1.06 x 0.97 in. (47.5 x 27.0 x 25.3 mm) Weight: 1.87 oz. (53 g)

Servo S9151 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral Power requirement: 4.8 V (from receiver)

Output torque: 131.9 oz.-in. (9.5 kg-cm) at 4.8V Operating speed: 0.19 sec/60 at 4.8V

Size: 1.57 x 0.79 x 1.44 in. (40.0 x 20.0 x 36.6 mm) Weight: 1.79 oz. (50 g)

Servo S9250 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral Power requirement: 4.8 V (from receiver)

Output torque: 76.4 oz.-in. (5.5 kg-cm) at 4.8V Operating speed: 0.11 sec/60 at 4.8V

Size: 1.59 x 0.79 x 1.48 in. (40.5 x 20.0 x 37.5 mm) Weight: 1.90 oz. (54 g)

Servo S9255 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral Power requirement: 4.8 V (from receiver)

Output torque: 125.0 oz.-in. (9.0 kg-cm) at 4.8V Operating speed: 0.16 sec/60 at 4.8V

Size: 1.57 x 0.79 x 1.44 in. (40.0 x 20.0 x 36.6 mm) Weight: 1.94 oz. (55 g)

Cautions on handling antenna

WARNING

Be sure to attach the antenna before operation.

*Antenna is stored in the antenna storage box in the transmitter.

Never hold the antenna alone.

*Hold the carrying bar, otherwise the main body can be damaged.

•Antenna storage

When you store the transmitter in the carrying case, detach the antenna and store it in the antenna compartment in the transmitter.

●Antenna Compartment

Cover

•Angle adjustment of the antenna

You can change the angle of the antenna, as you like. Use 2.5mm hexagonal wrench to turn counterclockwise to release the screw on the left of the antenna holder, and change the angle of the antenna, as you like, then retighten.

●Screw

LED monitor

The color of the FUTABA logo mark shows the status of the transmitter.

(LED Display)

•When you turn on the transmitter, FUTABA logo shows different colors, and then the color stays constantly pink. The FUTABA logo blinks green very rapidly while internal processing is carried out after the power is turned on. Once the internal processing is over, the logo turns to pink color.

•The FUTABA logo turns on blue when you use DSC cable, or when no is selected for transmit. when the trainer function is set at student’s side.

•The FUTABA logo blinks red slowly when you attach the RF module that is different from the setting.

•Under the normal usage (, that is, radio wave is being emitted), the FUTABA logo turns on green.

Switch reallocation

You can reallocate the toggle switches on the shoulders of the transmitter, as you like.

(Default settings)

*You can choose switch and set the ON-direction in the setting screen of the mixing functions.

•When you change switches:

●Screw

To relocate switches;

1.Make sure your transmitter is off, and use the attached 2.5mm hexagonal wrench (inside stylus) to turn the screw counter-clockwise on the switch block and detach the block.

●Projection

2.Disconnect the connectors of switches you want to change.

3.Use the attached jig (inside stylus) to turn the face nuts counterclockwise, this will detach the switches.

4.To re-attach, use the face nuts to attach switches from other positions or optional switches to the switch block.

5.Connect your connectors.

6.Insert the switch block so that it fits correctly into the body of the transmitter (as shown in the picture) and use the hexagonal wrench to tighten the screws.

Volume

●Locked state

Volume LD, CD, and RD:

If you push the volume to the bottom, the volume will stay there. If you push the volume again, the lock will be released and become operative again.

This volume is digital type (rotary encoder). This volume works as both a volume and a push-switch.

*T14MZ beeps when the volume knob reaches center.

*You can check the volume position on the Dial Monitor screen in the Linkage menu.

*You can use each setting screen of the mixing functions to select volumes and define the direction of its movement.

Slide Lever

LST (Left), RST (right):

Outside levers

LS (Left), RS (right):

Inside levers: Each lever has two ends, one in front and the other on the back.

*It sounds when the lever comes to the center.

*You can check the lever position on the dial-monitor screen in the linkage menu.

*You can select a slide lever and set the movement direction on the setting screen of mixing functions.

Digital trim

This transmitter is equipped with digital trims. Each time you press a trim button, the trim position moves one step. If you continue pressing it, the trim position starts to move faster. In addition, when the trim position returns to the center, the tone will change. You can always monitor trim positions by graphics on the screen. To change the trim rate, you must activate this through the function menu, within the linkage menu. Touch the trim button and you will access another screen which enables you to change the trim percentages.

Note: The trim positions you have set will be stored in the non-volatile memory and will remain there.

Touch Panel/ Rotary Key/ Direct Key

Touch panel, rotary keys and direct keys are used for entering data.

Touch Panel

Touch the panel with your finger or the attached stylus pen, which is also used as a toolbox, to enter data.

*Plastic film is attached on the glass of the touch panel. Please be careful so that you don’t scratch the touch panel with something hard, such as metal and sand sticking on the surface. And don’t push the touch panel too hard and don’t give any physical shock to the surface.Although you may find some air bubbles under the plastic panel due to environmental changes such as temperature, it is not a defect.

Rotary key

In addition to touch panel, you can select items by rotating the rotary keys to the left or to the right.

Direct key

You can directly call your favorite functions or menu screens.

(The default setting at the factory) S1: System menu

S2: Linkage menu S3: Model menu S4: Return

[How to change assignment of the direct key]

1.Open the screen you want to call. Then push S1 and S4 keys simultaneously. (You will see the direct key setting screen.)

2.Select the direct key.

Stick Adjustment

Adjustment of the stick lever angle

You can make fine adjustments to the angle of a stick lever either inwards or outwards from the center stick position.

●Screw

Use the attached 1.5mm hexagonal wrench (inside stylus) to turn the screw clockwise to adjust the stick outwards, or counter-clockwise to tilt it inward.

Note: The screw will fall out if you turn the screw counterclockwise too far.

Adjustment of the lever length

You can adjust the length of stick levers, as you like. It is recommended to adjust the length of the sticks in line with your hand size.

[How to adjust the length]

1.Hold the lever head «B» and turn the lever head «A» counter-clockwise, the lock will be released.

2.Turn the lever-head «A» clockwise as you hold the lever-head «B» after placing it as you like.

CF Card CFDP32M

CF (Compact Flash) card can store various files, such as model data, music, sound and pictures. Its memory size is 32MB.

Warning

Be sure to turn off the power to the transmitter before inserting or removing the CF card.

As the CF card is a precision device, do not use excessive force when inserting.

Be sure to use only Futaba’s original CF card, CFDP32M, for the T14MZ transmitter.

* Futaba does not recommend any CF cards other than Futaba’s original CF cards.

Set-up of CF card / Removal of CF card

1.Turn off the power to the transmitter.

2.Slide the card cover on the right side of the transmitter back, and pull open the cover towards you.

1. Slide backward the side cover of the transmitter.

2. Then, pull it toward you.

3.Inserting the card: Turn the CF card so that the name seal faces to the back of the transmitter. Then slide the card into the slot until the card touches bottom.

4.Press the card cover back and then slide it toward you to close it.

Removal of CF card:

1.Push the eject button and then take out the CF card.

2. Close the card cover and slide it to the original position.

●Eject

Button

●Side Cover

●CF Card

Read data from a PC

Saving music and image files edited by a PC into the CF card, you can use those files on your T14MZ transmitter. Equipment for reading and writing CF cards are available at most electronics stores.

[Important]

Before saving data from the PC, insert the CF card into the transmitter and turn on the power. To save a file from the PC, copy the file to a folder by file type, which are automatically written.

●BMP: Picture file ●WAV: Audio file ●WMA: Music file ●MODEL: Model data

*Use only CF card reader/writer that complies with CFA (CompactFlashTM Association) standard.

Stored data

The life of the CF card is limited due to the use of Flash memory. When you have a problem of saving or reading data such as picture data after a long period of use, please get a new CF card.

*We do not have the responsibility of compensating any failure or damage to the data stored in the memory card no matter what the reason is. Be sure to keep the backup of your important data in your CF card.

*No necessity for backup; T14MZ transmitters and CF cards are using nonvolatile memory devices so that the data stored in those will not be destroyed even without a backup battery. The clock for the transmitter depends on the Lithium battery.

Connector/Plug

Connector for trainer function (TRAINER)

When you use trainer function, connect the optional trainer cable between the transmitters for teacher and student.

*You can set the trainer function on the Trainer Function screen in the system menu.

Connector for DSC function (DSC)

You can operate the transmitter without transmitting radio waves by connecting the transmitter and the receiver to the DSC cable.

*Please refer to the section «Connection between Receiver/ Servo»

Audio plug (PHONE)

Connecting a stereo headphone to this plug, you can enjoy music files stored in the CF card.

Connector for battery charger (CHG)

This is the connector for charging the Lithium Ion battery LT2F2200 that is installed in the transmitter. Do not use any other chargers except CR-2500 that is for 12V application to charge the LT2F2200 battery through this connector.

Danger

Do not connect any other chargers except CR-2500 to this charging connector.

*If you take out the Lithium Ion battery LT2F2200 from the transmitter, you can use the attached charger LBC-1D5 for charging the battery.

USB port (Transmitter right side)

*This is for factory use only.

Installing and Removing of the battery LT2F2200 for the transmitter

Attachment of the battery

1.Hook one of your fingers in the slit formed by the transmitter’s main body and the battery cover on the bottom of the transmitter, and then pull up the cover to release the lock. You can now open the cover in the direction of the arrow.

2.Move the slide lever to the right end, and then install the battery in the holder.

Removing of the battery

Note: If you detach the battery while the power is on, the data you have set will not be saved.

1.Hook one of your fingers in the slit formed by the transmitter’s main body and the battery cover on the back and bottom of the transmitter, and then pull up the cover to release the lock. You can now open the cover in the direction of the arrow.

2.Slide the slide lever to the right while pressing it, the battery will be released.

●Move the slide lever to the far right.

3. Push the battery to the left with your finger.

4. Close and lock the battery cover until you hear a snapping sound.

Warning

Be careful to not drop the battery.

Never take out the battery from the T14MZ transmitter while the LED monitor is blinking

yellow after turning off the power the T14MZ transmitter.

*Internal devices such as memories may have been destroyed.

*If there is any problem, the message «Backup Error» will be shown the next time when you turn on the power of the transmitter. Do not use the transmitter as it is, send it back for a check to the Futaba Service Center.

Caution

Be sure to turn off the power of the transmitter before you attach or detach the module.

●Connector

Detachment of the RF module

Pull the module straight while you are pushing inward the projections on both sides of the module.

*There is a connector above and under the module respectively. So, you might find difficulty in pulling out the module if the module is tilted.

Attachment of the RF module

Insert the module with care so that the connecter pins of the transmitter won’t be bent.

●Tool for removing decoration nuts

●Rubber Cap

●Hex. Wrench (1.5mm and 2.5mm)

You can use the toolbox contained in the set for various adjustment of the transmitter.

Hexagonal wrench (1.5mm and 2.5mm)

These wrenches are for adjustment of sticks, replacement of the switches and adjustment of the antenna.

Tool for removing decoration nuts

This is for replacement of switches.

Stylus pen

Rubber cap is attached on the tip of the toolbox. You may use this tool as a stylus pen for operating touch panel. This stylus pen can let you do more precise operation than fingers without damaging the surface.

●You may use this tool as a stylus pen.

Safety precautions when you install receiver and servos

Warning

Connecting connectors

Be sure to insert the connector until it stops at the deepest point.

*If a connecter comes out during the flight due to some reasons such as vibration, your aircraft will crash.

Mounting servos

Use a vibration-proof rubber (such as rubber grommet) under a servo when mounting the

servo on a servo mount. And be sure that the servo cases do not touch directly to the metal parts such as servo mount.

*If a servo case is in direct contact with the airframe, the vibration of the airframe directly travels to and may damage the servo.

Servos throw

Adjust your system so that pushrods will not bind or sag when operating the servos to the

full extent.

*If excessive force is continuously applied to a servo, your aircraft may crash because the servo would be damaged and the battery would be consumed rapidly.

Mounting the power switch

When mounting a power switch to an airframe, make a rectangular hole that is a little larger than the total stroke of the switch so that you can turn ON/OFF without binding.

Avoid mounting the switch where it can be covered by engine oil and dust. In general, it is recommended to mount the power switch on the side of the fuselage that is opposite the muffler.

BASIC OPERATION

Battery Charging

Before charging batteries, read the «Cautions for handling battery and battery charger» in the section «For your safety».

How to charge the Lithium Ion battery

LT2F2200 for the transmitter

Danger

The Lithium-Ion battery LT2F2200 is only for your T14MZ. Do not use this battery for other

equipment.

Be sure to use the battery charger LBC-1D5 to charge the battery.

To charge the battery while installed in the transmitter, use the optional battery charger

CR-2500 for 12V.

[Method of charging battery]

to AC Outlet

1.Connect the power cable to the charger.

2.Connect the power cable of the charger to the wall socket (AC outlet).

*The power lamp turns on.

3.Mount the battery and then slide the battery in the direction shown in the figure until you hear a locking sound.

*The charge-lamp turns on and charging starts.

4. When the charge-lamp turns off, charging has been completed.

*Be sure to remove the power cable from the wall socket after using a battery charger.

*It takes about two and a half hours for charging the battery pack that has been used fully. However, the charging time may vary depending on the surrounding air temperature and the condition of the battery pack.

*The charge LED blinks (error) if the battery is improperly mounted or the battery itself is a defective product. In this case, remount the battery or use another battery.

*If you mount a charged battery, the charge lamp will turn on for several seconds, but it will turn off later.

How to charge the Ni-Cd battery NR4F1500 for the receiver

Use the battery charger FBC-32A that is included in the set.

[Method of charging battery]

AC Outlet

●Special Charger

FBC-32A

●Ni-Cd Battery

NR4F1500

1.Connect the power cable of the charger to the wall socket (AC outlet).

2.Connect the connector to the NiCd battery.

*Confirm that the charging indicator, LED lamp, is on.

3. Remove the battery after 15 hours.

*Battery charging will not automatically stop. Remove the battery from the charger and remove the charger from the wall socket.

*It is recommended to reactivate the battery by cycling several times if the battery has not been used for a long period.

*In case of NiCd battery, you may find the poor performance of the battery if you have used the battery only for a short period or if you repeat charging while the battery is not fully discharged. It is recommended to discharge the battery to the recommended level after your usage. It is also recommended to charge the battery just before your usage.

How to turn ON/OFF the power of the transmitter

Windows® CE is installed as a built-in operating system in the T14MZ transmitter. Compared to the conventional system, the T14MZ takes extra time for internal processing when it is turned on/off. For safety reasons, the radio will be emmiting only after you push the confirmation button when turning on the power. Please follow the instructions for turning on/off the transmitter.

When turning on the power of the transmitter

1. Turn on the power switch of the transmitter.

*After initialization of the transmitter is over, the frequency confirmation screen pops up, and LED monitor turns on pink.

2.Check the frequency shown on the screen. If it is OK, then click the button «YES».

*LED monitor turns to green and the transmitter begins to emit radio waves.

*If you push the button «NO», then the transmitter will not emit radio waves.

Then, you will see the home screen and you will be able to set conditions.

Start-up time; The time required for initializing the internal circuit of the transmitter varies between the previous time you turned off the transmitter and the time you will turned on the power. There are two “start up” modes for your transmitter, see below:

Cold start;

If you turn on the transmitter more than four hours after you last turned it off, the mode is “Cold start”. “Cold start” is normal for the first initial power up of the day. It will take about 30 seconds to be ready for use, as it takes time to initialize the internal circuit of the transmitter.

Hot start;

If you turn on the transmitter less than four hours after you last turned it off, the mode is “Hot start”. Since initialization has been partly completed, the transmitter will be ready to use in several seconds. “Hot start” takes place usually at a second flight or later flight in the day.

Warning

Once you turn on the power, never shut off the power switch until the power becomes stable

(or until the first screen shows up). If you turn off the power switch while the transmitter is going through the initialization process, the data could be damaged. Note: The start-up time may be a little bit slower when the CF card is installed compared to when the card is not.

How to stop the transmitter

Turn off the power switch of the transmitter. The internal circuit of the transmitter starts the shut down process including saving the set-up data. The LED will blink yellow while the transmitter is in the shutdown process.

Once you turn off the power, never operate the power switch until the power shutdown process

is fully completed. If you turn on the power switch again while the transmitter is still in the process of power shutdown, the data could be damaged.

As the internal circuit of the transmitter stays on the standby mode for 4 hours after turning off the power, some part of the circuit is consuming current. When you turn on the power during this period, the power starts in “Hot mode”. But if more than four hours pass after shutting down the power, the power supply will completely shut down the internal circuit. When you turn on the power after this point, the power starts in “Cold start mode”.

<Basic Operation> 25

●Reset Button

How to reset software

If the screen freezes for some reason and you cannot edit, the transmitter power supply is not shut off even if you turn OFF the power switch. You will need to use the reset button or remove the battery and reinsert it again. In this case, the power restarts in “Cold mode”. Even though the screen freezes, all the other functions for radio control operation remain operative.

How to change the frequency/How to set ID

The T14MZ system has employed the frequency synthesizer scheme. The T14MZ transmitter will set the frequency of the R5014DPS (PCMG3 receiver) by the wireless data transmission. When you are using a new PCMG3 receiver and changing the frequency, set ID or frequency by the following instructions.

In case of using PCMG3 receivers

*Make sure that PCM-G3 is set as a modulation scheme. Then change the frequency by the following instruction.

How to change the frequency

1.Turn on the power of the transmitter.

2.Push the area that shows the frequency in the home screen or push the «Frequency» button in the Linkage menu. Then the Frequency Set screen will pop up.

3.Push the «Receiver ID» button. Then ID inputting screen for receiver will pop up. Input the eight-digit ID code attached to the receiver’s case. Push the «Yes» button after confirming the ID.

*Use the «BS» button to move back digit by digit for correction if you made a mistake. If you want to stop changing ID code halfway, push «Return» button to return to the previous screen.

*Once you set the ID code for a receiver, you don’t have to set the ID code again as long as you change the receiver itself.

*When you need to use two receivers for a large size aircraft, you need to enter different ID codes to those receivers respectively.

4. Push the «Band NO. (Frequency)» button if you need to change the frequency. Then you will see frequencies on the screen. Select the frequency you want use. Push the button «Yes» after confirmation. Then you will see the «Confirmation of the change» box.

*If you have changed the module prior to turning on the power, confirmation screen will pop up to ask you whether you want to change the frequency. Push the button «Yes» to change the frequency.

5.If the frequency is correct, push the button «Yes». Then you will see the message «Transmitting the frequency data». It takes a certain time to send the new frequency data to the receiver with a sound. (If you need to resend the data, push the «Resend» button.)

6.Turn on the power of the receiver while the

new frequency data is displayed. When the frequency setting for the receiver is completed, the LED monitor of the receiver blinks once and the 1CH servo shuttles three times across the neutral position.

*A very low power, whose frequency is different from that of the channel frequency, is used to set the frequency of the receiver. The reachable distance of the radio is designed to be within several feet. Therefore, put the transmitter and the receiver as close as possible when setting the frequency of the receiver.

*If the receiver can not load the new data due to environmental reasons, connect the transmitter and the receiver directly by the DSC cable. And do the procedure 6 and 7.

*LED monitor will blink on and off if the receiver’s ID code is wrong. Then move back to the Receiver ID Set screen and restart the receiver’s ID setting from the beginning.

7. Push the button «End» when the frequency setting is completed. Then turn off the power of the transmitter following the instructions shown on the screen. You will be able to use the new frequency after you turn on the power again.

In case of using PCM1024, PPM receivers

*Make sure that PCM1024 or PPM is set as a modulation scheme. Then change the frequency by the following instruction.

How to change the frequency

1.Turn on the power of the transmitter.

2.Push the area that shows the frequency in the home screen or push the «Frequency» button in the Linkage menu. Then the Frequency Set screen will pop up.

3.Push the «Band NO. (Frequency)» button if you need to change the frequency. Then you will see frequencies on the screen. Select the frequency you want use. Push the button «Yes» after confirmation. Then you will see the «Confirmation of the change» box.

*If you have changed the module prior to turning on the power, confirmation screen will pop up to ask you whether you want to change the frequency. Push the button «Yes» to change the frequency.

4. If the frequency is correct, push the button «Yes». Turn off the power of the transmitter following the instructions shown on the screen. You will be able to use the new frequency after you turn on the power again.

Registration of the user’s name

T14MZ transmitter can register user’s name.

How to register user’s name

1.Turn on the power of the transmitter.

2.Push the area of the user’s name shown on the home screen or the «user’s name» in the linkage menu. Then the User’s Name Set screen will pop up.

3.Push the user’s name. Then the keyboard will pop up. You can use up to 32 characters as a user’s name. Use the keyboard on the screen to enter user’s name.

space key

4. Push «Return» key to return to the previous screen after entering the user’s name.

(If you want to protect the user’s name)

If you don’t want anybody else to change your user’s name, set your ID in the following way.

*Please be aware that you will not able to change user’s name if you forget your password.

1.Make sure that the security mode is «User’s name», and then push the User ID button.

2.Enter your password, using keyboard on the screen.

You will need to enter your password for changing the user’s name from the next time you turn on the power of the transmitter.

*Even if you enter the same character, your password will be identified differently depending on whether you are using «Transform» mode or «Direct» mode for inputting.

Timer

• To call the setting screen

Push [Timer1] or [Timer2] to call the timer setting screen.

•To display and reset the setting

Time and mode (UP/DN) are displayed here. Push this area for resetting the timer.

•To display, start and stop the timer

Timer is displayed here. Push this area to start/stop the timer.

Digital trim (T1 to T6, CD)

Push this area to call the Dial Monitor screen.

Condition

The condition name that is currently used is displayed here.

•Push this area to call the Condition Select screen.

Direct buttons

Select and push one of the direct buttons to call its setting screen.

Music playback

•Push this button to call the Music Playback screen.

System timer/Reset

•This shows the accumulated time up to now since the latest reset.

(Hour):(Minute):(Second)

Push this area to reset the timer.

Modulation mode/Frequency

Modulation mode is displayed here. (PCM-G3/PC M1024/PPM)

•Band number and frequency are displayed here.

•Push the frequency displaying area to call the Frequency Set screen.

Warning

Be sure to confirm the model name before flying your aircraft.

Check the remaining battery as often as possible and try to charge the battery earlier. If the battery

alarm makes a sound and its warning symbol is displayed, land your aircraft immediately.

Although you may notice the flickering of the numbers on the LCD screen, this is not an abnormal, because the LCD screen is frequently refreshing those even if those numbers are unchanged.

You can adjust the LCD contrast and the backlight brightness, and can change the duration time to turn off the backlight and color of the background by the screen setting in the system menu.

[Important notice]

Before downloading files from your PC into the CF card, insert the CF card into the transmitter and turn on the power of the transmitter. Then the following folders will be automatically created in the CF card. When you download files from you PC, copy and paste the files into their corresponding files.

•BMP : picture files

•WMA : music files

•WAV : sound files

•MODEL : model data files

Buttons for music playback

•You can playback any music files listed on the right side of the screen.

•If you adjust the volume here, it adjusts not only music playback but also other applications.

Multiple Music

Playback

• SW selection button

Push this button to call the SW select screen and choose the Music playback switch.

(Refer to the description in the end of this manual)

(Playback file list)

To playback

•All the music files saved in the CF card will be shown here.

1.Push the file name to select the music file you want to hear.

2.Use the buttons on the left to playback or stop the music.

The Trainer function makes it possible for the instructor to choose which functions and channels are to be used for instruction, making it possible to match the training ability to the student’s skill level. Two transmitters must be connected by an optional Trainer Cord, and the Instructorsʼ transmitter should be programmed for trainer operation, as described below.

When the Instructor activates the trainer switch, the student has control of the aircraft (if MIX or FUNC mode is turned on, the Instructor can make corrections while the student has control). When the switch is released the Instructor regains control. This is very useful if the student gets the aircraft into an undesirable situation.

NOTE: This trainer system can be used in the following manner;

1.In the T14MZ transmitter and a conventional transmitter, if the channel order is different. It is necessary to match the channel order in the Linkage Menu when connecting it with other than a T14MZ.

2.When the T14MZ is used as the Teacher, set the modulation mode of the student’ s transmitter to PPM. If being used as the student, set the T14MZ to the modulation mode specified by the Instructors’ transmitter. When the Instructors’ transmitter is a T14MZ, T9Z, T9C or T7C transmitter, it should be switched to PPM mode.

3.Be sure that all channels work correctly in both transmitters before flying.

●Touch the [Trainer] button at the System Menu to call the setup screen shown below.

●Return to System Menu

Corresponding types of transmitters:

T4VF, T6YG, T6YFK, T6X, T6EX, T7U, T7C, T8U, T9C, T9Z, T14MZ

Non-corresponding types of transmitters:

T6VA, T6DA

Teacher mode

1.Set «Teacher/Student» button to «Teacher».

2.Change «ACT/INH» button from «INH» to «OFF» or «ON».

3.Set «12CH/8CH» to «12CH» when the student is using T14MZ. Otherwise set it to «8CH».

4.Call up the Switch Setting screen by touching «Switch». Then set the desired switch and on/ off direction.

5.Select the switch mode. If you select «NORM», the trainer function will be turned on or off by a switch position. If you select «ALT», ON and OFF of the trainer function switches alternatively every time the switch is turned on. This means the student side can be operated without holding the switch lever.

6.The Instructor side selects the channel for control. Three operating modes are available.

«NORM» mode (Normal mode);

Student side has no control of mixes and settings in Teachers radio..

«MIX» mode;

Student has full advantage of all setting in Teachers radio, plus Teacher has the option to change any setting while Student has control.

«FUNC» mode (Function mode);

Student has control of mixes and rate settings of Teachers radio.

[Notes]

1. In the teacher mode, the trainer function display does not come on as long as the student’s transmitter is not receiving signals from the teacher’s transmitter (when the student’s transmitter is not connected).

Student mode

1.Set «Teacher/ Student» button to «Student».

2.Change «ACT/INH» button from «INH» to «OFF» or «ON».

3.Set «12CH/8CH» to «12CH» when the Instructor is using the T14MZ. Otherwise set it to «8CH».

Note: In «student mode», only the teacher side can turn on and off the power of the student’s transmitter. Keep the power switch always at off position. Note: In «teacher mode», the trainer function won’t be turned on unless the Instructors’ transmitter receives signals from the student’s transmitter. Be sure

●The setup screen for the student mode is shown below.

LCD contrast adjustment

1.Adjust the LCD contrast with the left and right side buttons.

*When the right side button is pressed, the LCD contrast decreases. When the left side button is pressed, the LCD contrast increases.

*The backlight consumes a large amount of power. We recommend you to turn off the backlight by setting the backlight power-off time to about one minute.

*Since the backlighting power consumption is extremely high, we recommend that the backlighting off time be made short.

Auto power off time setting

1. Adjust the auto power off time with the left and right side buttons.

*When the time the transmitter is inactive exceeds the set time, the power is turned off automatically. This time can be set up to 1 hour in 10 minutes increments. The auto power off function can also be deactivated.

Backlighting brightness adjustment

1. Adjust the backlighting brightness with the left and right side buttons.

*When the right side button is touched, the backlighting becomes brighter. When the left side button is touched, the backlighting becomes darker.

Backlight power-off time

You can set a time period to turn off the LCD backlight. This function counts the period that the touch panel has been not operated. This time can be set by ten-second steps. You can also turn off the backlight-power-off” if you like.

Background color

1. Touch the button of the color you want to change.

*There are four background colors.

Touch panel calibration

This function adjusts the location of touch panel. Touch «Calibration» button and then press «Yes», the calibration screen will pop up. Touch the center of the cross hair cursor on the screen with the stylus pen. As soon as the system recognizes the position, the cursor will move on to the next position. Repeat this procedure as long as the cursor moves to next position. You will do this five times. Calibration will be carried out based on the five positions. Disappearance of the cross hair cursor means the calibration has been completed. Touch any point on the screen to return to the previous screen.

*In ordinary operation, this calibration is not necessary. If you notice the touch panel is not functioning correctly after long use, we recommend you to carry out this calibration.

The integrating timer can also be reset.

*The integrating timer is displayed on the Home screen.

This function registers the T14MZ user name.

A PIN can also be set to protect the set data or user name.

User name registration

1.When the User Name box is touched, a keyboard appears on the screen.

2.Enter the user name from this keyboard.

*A user name of up to 32 characters can be entered.

*The set user name is displayed on the Home screen.

(For a detailed description of the input method, see [User Name Registration/Character Input Method] in the Basic Operation section.)

3.When the «Return» key is touched 2 times, the display returns to the preceding screen.

4.When the transmitter power is turned off, the set security mode becomes active.

*When a PIN is set at the user name, it must be entered the next time the User Name screen is opened.

When a System PIN is set, a button displaying a key icon appears on the Home screen.

When you want to change the setting, touch this button and enter the PIN.

User name or set data protection

1. Touch the Security Mode button and select the mode. The mode is switched each time the button is touched.

*User Name: Select when you want to protect the user name only.

*System: Select when you want to protect all the set data.

2. When the user ID button is touched, a PIN input screen appears. Input a PIN of up to 4 digits.

Switch selection

1.Select the switch type by touching the [type] button corresponding to the switch to be replaced.

[Lever]: Toggle switch [Button]: Pushbutton

[Dial]: Knob

●Setting for toggle switch is shown above.

2/3 position selection

1.Touch the «Posi.» button corresponding to the switch and select the position type.

[2 Posi]: 2 position [3 Posi]: 3 position

[Alt/Mom] mode selection

1. Select the operation mode by touching the [Alt/Mom] button corresponding to the switch.

[Alt.]: Alternate type [Mom.]: Self-return type

●Selection of the [Mom.] mode with a 3-position type switch is shown above.

«3P Mom» mode selection

1. Select the operation mode by touching the «3P Mom» button corresponding to the switch.

[Single]: One-side self-return type [Dual]: Both directions self-return type

Airplane/glider basic setting procedure

1. Model addition and call

Initial setting assigns 1 model to the T14MZ transmitter. The Model Select function of the Linkage Menu is used to add models and to call models which are already set.

This is convenient when calling a model after its name has been registered. (The data of up to 30 models can be saved to the transmitter. Data can also be saved to the accessory Data-Pack.)

The currently called model name is displayed at the top of the screen. Before flying and before changing any settings, always confirm the model name.

When a new model was added, the Model type select screen and Frequency/Modulation mode/ Receiver ID setup screen automatically appear. After changing or confirming the model, turn the power off and on according to the instructions on the screen. Please be aware that the transmitter will stop transmitting when you change the model.

2. Model type selection

Select the model type matched to the fuselage with the Model Type select function of the Linkage Menu. For an airplane, select the model type from among the 3 types: airplane, glider, and motor glider. When the Wing type select screen is displayed and the wing type is selected when selecting the model type, the Tail type select screen is displayed. Select the tail type matched to the fuselage.

There are 13 wing types and 3 tail types for airplane, glider, and motor glider.

3. Fuselage linkage

Link the ailerons, elevators, throttle, rudder, etc. in accordance with the model’s instruction manual. For a description of the connection method, see the Receiver and Servos Connection.

Note: The channel assignment of the T14MZ is different from that of our existing systems. Note that even for the same «airplane model», when the wing type and tail type are different, the channel

assignment may be different. (The channel assigned to each function can be checked at the Function menu of the Linkage Menu.)

●When the direction of the linkage is reversed, adjust the direction with the Reverse function of the Linkage Menu.

●Connect the throttle linkage so carburetor is open at full trim and full open then the throttle can be cut.

●Adjust the neutral position and rudder angle with the linkage, and fine tune them with the Sub Trim and End Point functions (rudder angle adjustment). To protect the linkage, a limit position can also be set with the End Point function. The End Point function can adjust the amount of up/down and left/right movement, limit, and servo speed of each channel.