Alcosafe kx 6000s4 инструкция по применению

AlcoSafe KX6000S EN 8 Display test result records KX6000S stores BAC test results up to 64 records. The stored records could be recalled as below: On Welcome screen, press Right button for 2 seconds. SET mode is displayed. Again press Right button to enter the REC (Record) mode. Press Power button to display the latest record (indicated by the serial number ‘1’ on the screen, followed by the corresponding result) Press Power button again and so on to display the next records sequentially. Press Right button to see the records in reverse time direction. Press Right button to exit REC (Record) mode.

AlcoSafe KX6000S EN Installing the batteries Press down the battery cover with small amount of pressure located on the back of the unit. Push down and slide away from the unit to release the cover. Install 2 AA ALKALINE batteries and close the battery cover. How to use IMPORTANT! Wait 20 Minutes No Drinking No Smoking Wait 20 minutes after the subject drinks, smokes or eats before testing. Failure to wait 20 minutes can give inaccurate BAC readings. Insert mouthpiece: Insert the KX6000S mouthpiece rmly into the mouthpiece slot on the upper left hand side of the

AlcoSafe KX6000S EN Owner’s Manual KX6000S premium digital alcohol breath detector Please read this user manual before use. Result of this unit for reference only. Use ALKALINE batteries only. DO NOT DRINK AND DRIVE! TM

EN The AlcoSafe KX6000S is a premium grade digital alcohol breath detector that quickly screens for the presence of alcohol in breath. The LCD-LED Dual display indicates the Blood Alco- hol Content (BAC) in forms of numeric result (LCD) and alert lights in Green/Yellow/Red (LED) for the test subject in seconds. Please read this manual entirely before use. Components Diagram 1 Mouthpiece Slot LCD-LED Dual Display Left Button (Select / Begin test) Power Button (OK / Conrm) Right Button (Recall last record / Access user menu) Battery Compartment Mouthpiece Holder (Hold

AlcoSafe KX6000S EN 10 Error messages Error message Cause and Course of Action REP This message means insucient or uneven blowing is detected. Repeat ‘HOW TO USE’ steps 2 – 6. REP + Snr This message means Sensor Not Ready (Snr) and the unit needs another warm-up / autocleansing. It occurs when the unit has not been used for long time / occurs when there is alcohol residue on the sensor. Another autocleans- ing process is needed. Repeat ‘HOW TO USE’ steps 2 – 6. H This message displays when the unit detected a very high alcohol concentration (above 4.0‰ BAC). Err This message displays when the sensor has sustain

AlcoSafe KX6000S EN On Screen Menu — Navigation path 5 SET temperature display format SET BAC display format SET alert level (Refer to page 6) (Refer to page 6) (Refer to page 7) On Welcome screen, Press Right button for 2 seconds to enter the menu structure of : — SET (Temperature display format, BAC display format, Alert level, Beep sound) — REC (Display test result record) — TEST (Display cumulative test count) — CAL (Calibration) SET beep sound when blowing (Refer to page 7) Display test result records (Refer to page Display

EN Step 6 Read the results: The reading would be in range from 0.0 to 4.0 ‰BAC (i.e: 0.00 to 0.40%BAC or 0.00 to 2.00 mg/l) depending on the user pre-set BAC display format. Note: Refer to ‘Set BAC display format’ for more about how to change the display format for the BAC result Step 4 Ready: Wait until ‘RDY’ (Ready) appears with a single “beep” indicates the unit is ready to use. 3 Blowing: BLOW STEADILY into the mouthpiece for 5 seconds. “BLOW 1-5.

AlcoSafe KX6000S Specications EN BAC Detection Range 0.0 to 4.0 ‰BAC (i.e: 0.00 to 0.40%BAC or 0.00 to 2.00 mg/l) Accuracy +/- 0.1 ‰BAC or +/- 0.01 %BAC at cal. point Warmup Between 20-60 seconds Response time 5 seconds Sensor Premium Sensitive Semiconductor Operating temperature 10 — 40°C (50 — 104°F) Display panel LCD-LED Dual Display with backlight. DOT matrix display with system messages Power Two 1.5V AA Alkaline Batteries (Not Included) Battery life Approx. 200 — 300 tests with new batteries Dimensions 114 x 51 x 18 mm Recal

AlcoSafe KX6000S EN Set alert level Set beep sound when blowing KX6000 gives alert message (RED light, blinking reading, beeping sound) when the BAC result exceeded the alert level. Alert level could be set at dierent levels (0.2 / 0.3 / 0.4 / 0.5 / 0.8 / 1.0 ‰BAC) as below: On Welcome screen, press Right button for 2 seconds. SET mode is displayed. Press Power button 3 times to enter SET mode for setting alert level. Current alert level blinks. Press Left button to select your desired alert level between (0.2

EN LOW — Green LED light ‰BAC (g/l) 0.0 — 0.1 %BAC 0.00 — 0.01 mg/l 0.00 — 0.005 ATTN — Yellow LED light ‰BAC (g/l) Between 0.1 and alert level (0.5g/l) %BAC Between 0.01 and alert level (0.05%BAC) mg/l Between 0.005 and alert level (0.25mg/l) HIGH — Red LED light ‰BAC (g/l) Reaches or exceeds alert level %BAC Reaches or exceeds alert level mg/l Reaches or exceeds alert level KX6000S detects BAC within the range 0.0 to 4.0 ‰BAC (i.e: 0.00 to 0.40%BAC or 0.00 to 2.00 mg/l). Dierent system

AlcoSafe KX6000S Calibration The KX6000S is calibrated during manufacture using advanced alcohol simulation equipment. Known alcohol concentrations are passed through the sensor to set baseline values for testing. During testing, the unit compares users’ breath samples to these baseline values. The accuracy of breath alcohol testers can uctuate after six to twelve months of normal use, depending on the number of tests performed and operating condi- tions. If this product is providing inconsistent test results, is not providing any test results, or provides unusually high or low test r

KX6000S Don’t Risk It, Know Your Limit. Do Not Drink And Drive! TM

Calibration The KX6000S is calibrated during manufacture using advanced alcohol simulation equipment. Known alcohol concentrations are passed through the sensor to set baseline values for testing. During testing, the unit compares users’ breath samples to these baseline values. The accuracy of breath alcohol testers can uctuate after six to twelve months of normal use, depending on the number of tests performed and operating condi- tions. If this product is providing inconsistent test results,

KX6000S Don’t Risk It, Know Your Limit. Do Not Drink And Drive! TM

EN Set alert level Set beep sound when blowing KX6000 gives alert message (RED light, blinking reading, beeping sound) when the BAC result exceeded the alert level. Alert level could be set at dierent levels (0.2 / 0.3 / 0.4 / 0.5 / 0.8 / 1.0 ‰BAC) as below: On Welcome screen, press Right button for 2 seconds. SET mode is displayed. Press Power button 3 times to enter SET mode for setting alert level. Current alert level blinks. Press Left button to select your des

AlcoSafe KX6000S EN The AlcoSafe KX6000S is a premium grade digital alcohol breath detector that quickly screens for the presence of alcohol in breath. The LCD-LED Dual display indicates the Blood Alco- hol Content (BAC) in forms of numeric result (LCD) and alert lights in Green/Yellow/Red (LED) for the test subject in seconds. Please read this manual entirely before use. Components Diagram 1 Mouthpiece Slot LCD-LED Dual Display Left Button (Select / Begin test) Power Button (OK / Conrm) Right Button (Recall last record / A

AlcoSafe KX6000S Specications EN BAC Detection Range 0.0 to 4.0 ‰BAC (i.e: 0.00 to 0.40%BAC or 0.00 to 2.00 mg/l) Accuracy +/- 0.1 ‰BAC or +/- 0.01 %BAC at cal. point Warmup Between 20-60 seconds Response time 5 seconds Sensor Premium Sensitive Semiconductor Operating temperature 10 — 40°C (50 — 104°F) Display panel LCD-LED Dual Display with backlight. DOT matrix display with system messages Power Two 1.5V AA Alkaline Batteries (Not Included) Battery life Approx. 200 — 300 tests with new batteries Dimensions 114 x 51 x 18 mm Recalibration Recom

EN 10 Error messages Error message Cause and Course of Action REP This message means insucient or uneven blowing is detected. Repeat ‘HOW TO USE’ steps 2 – 6. REP + Snr This message means Sensor Not Ready (Snr) and the unit needs another warm-up / autocleansing. It occurs when the unit has not been used for long time / occurs when there is alcohol residue on the sensor. Another autocleans- ing process is needed. Repeat ‘HOW TO USE’ steps 2 – 6. H This message

AlcoSafe KX6000S Set temperature display format EN Set BAC display format KX6000S displays temperature in format of Celsius °C / Fahrenheit °F. The display format could be set as below: On Welcome screen, press Right button for 2 seconds. SET mode is displayed. Press Left button to select your desired temperature display format between Celsius °C / Fahrenheit °F. Press Power button to conrm setting. Press Power button 1 time to enter SET mode for setting temper- ature display format. Current temperature display format blinks. KX6000S displays BAC result in f

AlcoSafe KX6000S EN On Screen Menu — Navigation path 5 SET temperature display format SET BAC display format SET alert level (Refer to page 6) (Refer to page 6) (Refer to page 7) On Welcome screen, Press Right button for 2 seconds to enter the menu structure of : — SET (Temperature display format, BAC display format, Alert level, Beep sound) — REC (Display test result record) — TEST (Display cumulative test count) — CAL (Calibration) SET beep sound when blowing (Refer to page 7) Display test result records (Refer to page Display cumulative test count (Refer to

AlcoSafe KX6000S EN 8 Display test result records KX6000S stores BAC test results up to 64 records. The stored records could be recalled as below: On Welcome screen, press Right button for 2 seconds. SET mode is displayed. Again press Right button to enter the REC (Record) mode. Press Power button to display the latest record (indicated by the serial number ‘1’ on the screen, followed by the corresponding result) Press Power button again and so on to display the next records sequentially. Press Right button to see the records in reverse time direction. Press Right button to exit REC (Record) mode. Press Right button 3 more time

AlcoSafe KX6000S EN Installing the batteries Press down the battery cover with small amount of pressure located on the back of the unit. Push down and slide away from the unit to release the cover. Install 2 AA ALKALINE batteries and close the battery cover. How to use IMPORTANT! Wait 20 Minutes No Drinking No Smoking Wait 20 minutes after the subject drinks, smokes or eats before testing. Failure to wait 20 minutes can give inaccurate BAC readings. Insert mouthpiece: Insert the KX6000S mouthpiece rmly into the mouthpiece slot on the upper left hand side of the uni

AlcoSafe KX6000S EN Step 6 Read the results: The reading would be in range from 0.0 to 4.0 ‰BAC (i.e: 0.00 to 0.40%BAC or 0.00 to 2.00 mg/l) depending on the user pre-set BAC display format. Note: Refer to ‘Set BAC display format’ for more about how to change the display format for the BAC result Step 4 Ready: Wait until ‘RDY’ (Ready) appears with a single “beep” indicates the unit is ready to use. 3 Blowing: BLOW STEADILY into the mouthpiece for 5 seconds. “BLOW 1-5…” appears on display indicating s

AlcoSafe KX6000S EN Owner’s Manual KX6000S premium digital alcohol breath detector Please read this user manual before use. Result of this unit for reference only. Use ALKALINE batteries only. DO NOT DRINK AND DRIVE! TM